On Thu, 20 Jul 2023 17:40:03 +0200
Andrea Collamati <andrea.collamati@xxxxxxxxx> wrote:
> MCP4728 is a 12-bit quad channel DAC with I2C interface.
>
> support for:
> * per-channel gain
> * per-channel power state
> * per-channel power down mode control
> * per-channel vref selection internal/vdd
> * store current state to on-chip EEPROM
>
> Signed-off-by: Andrea Collamati <andrea.collamati@xxxxxxxxx>
Hi Andrea,
Given the question was raised about similar parts, I took a quick look
and to me this look different enough from parts already supported that
a new driver is reasonable.
Biggest thing to address here is the custom ABI.
1) I tend to resist that wherever possible - it will be little used (because it's custom)
and rather defeats the point of a unfied subsystem.
2) It's not documented ;) Without docs, very low chance of acceptance or even
good review.
Comments inline.
> ---
> drivers/iio/dac/Kconfig | 11 +
> drivers/iio/dac/Makefile | 1 +
> drivers/iio/dac/mcp4728.c | 638 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 650 insertions(+)
> create mode 100644 drivers/iio/dac/mcp4728.c
>
> diff --git a/drivers/iio/dac/mcp4728.c b/drivers/iio/dac/mcp4728.c
> new file mode 100644
> index 000000000000..39237dba27ba
> --- /dev/null
> +++ b/drivers/iio/dac/mcp4728.c
> @@ -0,0 +1,638 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Support for Microchip MCP4728
> + *
> + * Copyright (C) 2023 Andrea Collamati <andrea.collamati@xxxxxxxxx>
> + *
> + * Based on mcp4725 by Peter Meerwald <pmeerw@xxxxxxxxxx>
> + *
> + * Driver for the Microchip I2C 12-bit digital-to-analog quad channels
> + * converter (DAC).
> + *
> + * (7-bit I2C slave address 0x60, the three LSBs can be configured in
> + * hardware)
> + */
> +
> +#include <linux/module.h>
> +#include <linux/i2c.h>
> +#include <linux/err.h>
> +#include <linux/delay.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/property.h>
Prefer alphabetical order. The groups you have are fine.
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +
> +#define MCP4728_DRV_NAME "mcp4728"
Normally better to just put this inline. It's not repeated much.
> +
> +#define MCP4728_RESOLUTION 12
> +#define MCP4728_N_CHANNELS 4
> +
> +#define MCP4728_CMD_POS 3
> +#define MCP4728_CMD_UDAC_POS 0
> +#define MCP4728_CMD_CH_SEL_POS 1
> +
> +#define MCP4728_CMD_VREF_MASK 0x80
> +#define MCP4728_CMD_VREF_POS 7
> +
> +#define MCP4728_CMD_PDMODE_MASK 0x60
> +#define MCP4728_CMD_PDMODE_POS 5
> +
> +#define MCP4728_CMD_GAIN_MASK 0x10
> +#define MCP4728_CMD_GAIN_POS 4
All these should be just the masks then use FIELD_PREP() / FIELD_GET()
> +
> +#define MCP4728_MW_CMD 0x08 // Multiwrite Command
> +#define MCP4728_SW_CMD 0x0A // Sequential Write Command (include eeprom)
/* */ comments only for consistency with rest of the drivers in IIO
> +
> +#define MCP4728_READ_RESPONSE_LEN (MCP4728_N_CHANNELS * 3 * 2)
> +#define MCP4728_WRITE_EEPROM_LEN (1 + MCP4728_N_CHANNELS * 2)
> +
> +static ssize_t mcp4728_store_eeprom(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + u8 outbuf[MCP4728_WRITE_EEPROM_LEN];
> + int tries = 20;
> + u8 inbuf[3];
> + bool state;
> + int ret;
> + unsigned int i;
> +
> + ret = kstrtobool(buf, &state);
> + if (ret < 0)
> + return ret;
> +
> + if (!state)
> + return 0;
> +
> + outbuf[0] = MCP4728_SW_CMD << MCP4728_CMD_POS; // Command ID
FIELD_PREP()
> +
> + for (i = 0; i < MCP4728_N_CHANNELS; i++) {
> + struct mcp4728_channel_data *ch = &data->channel_data[i];
> + int offset = 1 + i * 2;
> +
> + outbuf[offset] = ch->ref_mode << MCP4728_CMD_VREF_POS;
FIELD_PREP() etc in similar places throughout.
> + if (data->powerdown) {
> + u8 mcp4728_pd_mode = ch->pd_mode + 1;
> +
> + outbuf[offset] |= mcp4728_pd_mode
> + << MCP4728_CMD_PDMODE_POS;
> + }
> +
> + outbuf[offset] |= ch->g_mode << MCP4728_CMD_GAIN_POS;
> + outbuf[offset] |= ch->dac_value >> 8;
> + outbuf[offset + 1] = ch->dac_value & 0xff;
> + }
> +
> + ret = i2c_master_send(data->client, outbuf, MCP4728_WRITE_EEPROM_LEN);
> + if (ret < 0)
> + return ret;
> + else if (ret != MCP4728_WRITE_EEPROM_LEN)
> + return -EIO;
> +
> + /* wait RDY signal for write complete, takes up to 50ms */
> + while (tries--) {
> + msleep(20);
> + ret = i2c_master_recv(data->client, inbuf, 3);
> + if (ret < 0)
> + return ret;
> + else if (ret != 3)
> + return -EIO;
> +
> + if (inbuf[0] & 0x80) // check RDY flag
> + break;
> + }
> +
> + if (tries < 0) {
> + dev_err(&data->client->dev, "%s failed, incomplete\n",
> + __func__);
> + return -EIO;
> + }
> + return len;
> +}
> +
> +static IIO_DEVICE_ATTR(store_eeprom, 0200, NULL, mcp4728_store_eeprom, 0);
> +
> +static struct attribute *mcp4728_attributes[] = {
> + &iio_dev_attr_store_eeprom.dev_attr.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group mcp4728_attribute_group = {
> + .attrs = mcp4728_attributes,
> +};
> +
> +enum chip_id {
> + MCP4728,
Don't introduce any infrastructure for multiple support devices until
you add support for a second device. Right now it is just nose.
> +};
> +
> +static int mcp4728_program_channel_cfg(int channel, struct iio_dev *indio_dev)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + struct mcp4728_channel_data *ch = &data->channel_data[channel];
> + u8 outbuf[3];
> + int ret;
> +
> + outbuf[0] = MCP4728_MW_CMD << MCP4728_CMD_POS; // Command ID
> + outbuf[0] |= channel << MCP4728_CMD_CH_SEL_POS; // Channel Selector
FIELD_PREP()
> + outbuf[0] |= 0; // UDAC = 0
> +
> + outbuf[1] = ch->ref_mode << MCP4728_CMD_VREF_POS;
> +
> + if (data->powerdown) {
> + u8 mcp4728_pd_mode = ch->pd_mode + 1;
> +
> + outbuf[1] |= mcp4728_pd_mode << MCP4728_CMD_PDMODE_POS;
> + }
> +
> + outbuf[1] |= ch->g_mode << MCP4728_CMD_GAIN_POS;
FIELD_PREP()
> + outbuf[1] |= ch->dac_value >> 8;
> + outbuf[2] = ch->dac_value & 0xff;
put_unaligned_be16()
> +
> + ret = i2c_master_send(data->client, outbuf, 3);
> + if (ret < 0)
> + return ret;
> + else if (ret != 3)
> + return -EIO;
> + else
Drop the else - this is the non error condition.
> + return 0;
> +}
> +
> +// powerdown mode
> +static const char *const mcp4728_powerdown_modes[] = { "1kohm_to_gnd",
> + "100kohm_to_gnd",
> + "500kohm_to_gnd" };
> +
> +static int mcp4728_get_powerdown_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + return data->channel_data[chan->channel].pd_mode;
> +}
> +
> +static int mcp4728_set_powerdown_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + unsigned int mode)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + data->channel_data[chan->channel].pd_mode = mode;
> +
> + return 0;
> +}
> +
> +static ssize_t mcp4728_read_powerdown(struct iio_dev *indio_dev,
> + uintptr_t private,
> + const struct iio_chan_spec *chan,
> + char *buf)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + return sysfs_emit(buf, "%d\n", data->powerdown);
> +}
> +
> +static ssize_t mcp4728_write_powerdown(struct iio_dev *indio_dev,
> + uintptr_t private,
> + const struct iio_chan_spec *chan,
> + const char *buf, size_t len)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + bool state;
> + int ret;
> +
> + ret = kstrtobool(buf, &state);
> + if (ret)
> + return ret;
> +
> + if (state)
> + ret = mcp4728_suspend(&data->client->dev);
> + else
> + ret = mcp4728_resume(&data->client->dev);
> +
> + if (ret < 0)
> + return ret;
> +
> + return len;
Don't support custom powering down. If this is needed it should be
using the existing power management flows.
Might have been more interesting if it were per channel, but it's not.
(and I have no idea off the top of my head on how we would deal with it
if it were per channel).
> +}
> +
> +static const struct iio_enum mcp4728_powerdown_mode_enum = {
> + .items = mcp4728_powerdown_modes,
> + .num_items = ARRAY_SIZE(mcp4728_powerdown_modes),
> + .get = mcp4728_get_powerdown_mode,
> + .set = mcp4728_set_powerdown_mode,
> +};
> +
> +// vref mode
No c++ comments in IIO (other than for the spdx thing)
> +static const char *const mcp4728_vref_modes[] = {
> + "vdd_ext",
> + "internal",
> +};
> +
> +static int mcp4728_get_vref_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + return data->channel_data[chan->channel].ref_mode;
> +}
> +
> +static int mcp4728_set_vref_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + unsigned int mode)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + data->channel_data[chan->channel].ref_mode = mode;
> +
> + if (mode == MCP4728_VREF_EXTERNAL_VDD &&
> + data->channel_data[chan->channel].g_mode == MCP4728_GAIN_X2) {
> + dev_warn(&data->client->dev,
> + "CH%d: Gain x2 not effective when vref is vdd, force to x1",
> + chan->channel);
Even better if you don't present the option at all and wrap it up in the
standard ABI of _scale
> + data->channel_data[chan->channel].g_mode = MCP4728_GAIN_X1;
> + }
> +
> + ret = mcp4728_program_channel_cfg(chan->channel, indio_dev);
> +
> + return ret;
return mcp...
> +}
> +
> +static const struct iio_enum mcp4728_vref_mode_enum = {
> + .items = mcp4728_vref_modes,
> + .num_items = ARRAY_SIZE(mcp4728_vref_modes),
> + .get = mcp4728_get_vref_mode,
> + .set = mcp4728_set_vref_mode,
> +};
> +
> +// gain
> +static const char *const mcp4728_gain_modes[] = {
> + "x1",
> + "x2",
Map this to _SCALE probably as a set of values combined with the
reference select.
Also, use numbers for ABI where possible. x2 is a pain for software
library to mess around with.
> +};
> +
> +static int mcp4728_get_gain_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + return data->channel_data[chan->channel].g_mode;
> +}
> +
> +static int mcp4728_set_gain_mode(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + unsigned int mode)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + if (mode == MCP4728_GAIN_X2 &&
> + data->channel_data[chan->channel].ref_mode ==
> + MCP4728_VREF_EXTERNAL_VDD) {
> + dev_err(&data->client->dev,
> + "CH%d: Gain x2 not effective when vref is vdd",
> + chan->channel);
> + return -EINVAL;
> + }
> +
> + data->channel_data[chan->channel].g_mode = mode;
> +
> + ret = mcp4728_program_channel_cfg(chan->channel, indio_dev);
> +
> + return ret;
> +}
> +
> +static const struct iio_enum mcp4728_gain_mode_enum = {
> + .items = mcp4728_gain_modes,
> + .num_items = ARRAY_SIZE(mcp4728_gain_modes),
> + .get = mcp4728_get_gain_mode,
> + .set = mcp4728_set_gain_mode,
> +};
> +
> +static const struct iio_chan_spec_ext_info mcp4728_ext_info[] = {
> + {
> + .name = "powerdown",
> + .read = mcp4728_read_powerdown,
> + .write = mcp4728_write_powerdown,
> + .shared = IIO_SEPARATE,
> + },
> + IIO_ENUM("powerdown_mode", IIO_SEPARATE, &mcp4728_powerdown_mode_enum),
> + IIO_ENUM_AVAILABLE("powerdown_mode", IIO_SHARED_BY_TYPE,
> + &mcp4728_powerdown_mode_enum),
> + IIO_ENUM("vref_mode", IIO_SEPARATE, &mcp4728_vref_mode_enum),
> + IIO_ENUM_AVAILABLE("vref_mode", IIO_SHARED_BY_TYPE,
> + &mcp4728_vref_mode_enum),
> + IIO_ENUM("gain_mode", IIO_SEPARATE, &mcp4728_gain_mode_enum),
> + IIO_ENUM_AVAILABLE("gain_mode", IIO_SHARED_BY_TYPE,
> + &mcp4728_gain_mode_enum),
Custom ABI is basically ABI no software will use. Also to even start attempting
to get that accepted for a driver, we need documentation in
Documentation/ABI/testing/sysfs-bus-iio-*
> + {},
> +};
> +
> +static const struct iio_chan_spec mcp4728_channels[MCP4728_N_CHANNELS] = {
> + MCP4728_CHAN(0),
> + MCP4728_CHAN(1),
> + MCP4728_CHAN(2),
> + MCP4728_CHAN(3),
> +};
> +
> +static int mcp4728_full_scale_mV(u32 *full_scale_mV, int channel,
> + struct mcp4728_data *data)
> +{
> + int ret;
> +
> + if (data->channel_data[channel].ref_mode == MCP4728_VREF_EXTERNAL_VDD)
> + ret = regulator_get_voltage(data->vdd_reg);
> + else
> + ret = 2048000;
> +
> + if (ret < 0)
> + return ret;
> +
> + if (ret == 0)
> + return -EINVAL;
> +
> + *full_scale_mV = ret / 1000;
> + return 0;
> +}
> +
> +static u32 mcp4728_raw_to_mV(u32 raw, int channel, struct mcp4728_data *data)
> +{
> + int ret;
> + u32 full_scale_mV;
> +
> + ret = mcp4728_full_scale_mV(&full_scale_mV, channel, data);
> + if (ret)
> + return ret;
> +
> + return (((raw + 1) * full_scale_mV) >> MCP4728_RESOLUTION);
This looks like a linear transformation. If so that's a job for userspace and
you should expose the raw channel values + the scaling.
> +}
> +
> +static int mcp4728_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val,
> + int *val2, long mask)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + *val = data->channel_data[chan->channel].dac_value;
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_SCALE:
> + if (data->channel_data[chan->channel].ref_mode ==
> + MCP4728_VREF_EXTERNAL_VDD)
> + ret = regulator_get_voltage(data->vdd_reg);
> + else
> + ret = 2048000;
> +
> + if (ret < 0)
> + return ret;
> +
> + *val = ret / 1000;
> + *val2 = MCP4728_RESOLUTION;
> + return IIO_VAL_FRACTIONAL_LOG2;
> + }
> + return -EINVAL;
> +}
> +
> +static int mcp4728_write_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int val,
> + int val2, long mask)
> +{
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + if (val < 0 || val > GENMASK(MCP4728_RESOLUTION - 1, 0))
> + return -EINVAL;
> + data->channel_data[chan->channel].dac_value = val;
> + ret = mcp4728_program_channel_cfg(chan->channel, indio_dev);
> + break;
> + default:
> + ret = -EINVAL;
> + break;
> + }
> +
> + return ret;
> +}
> +
> +static const struct iio_info mcp4728_info = {
> + .read_raw = mcp4728_read_raw,
> + .write_raw = mcp4728_write_raw,
> + .attrs = &mcp4728_attribute_group,
> +};
> +
> +static int mcp4728_suspend(struct device *dev)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int err = 0;
> + unsigned int i;
> +
> + data->powerdown = true;
> +
> + for (i = 0; i < MCP4728_N_CHANNELS; i++) {
> + int ret = mcp4728_program_channel_cfg(i, indio_dev);
> +
> + if (ret)
> + err = ret;
> + }
> + return err;
> +}
> +
> +static int mcp4728_resume(struct device *dev)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
I don't feel strongly about this, but chances are this will get
simplified to not bounce from dev to i2c client and back again.
dev_get_drvdata(dev)
> + struct mcp4728_data *data = iio_priv(indio_dev);
> + int err = 0;
> + unsigned int i;
> +
> + data->powerdown = false;
> +
> + for (i = 0; i < MCP4728_N_CHANNELS; i++) {
> + int ret = mcp4728_program_channel_cfg(i, indio_dev);
> +
> + if (ret)
> + err = ret;
Generally if an error occured, stop poking the device. So error out
immediately. I can see the logic in trying to continue, but an error
on a device like this normally indicates something is going very wrong
so muddling on won't succeed.
> + }
> + return err;
> +}
> +
> +static DEFINE_SIMPLE_DEV_PM_OPS(mcp4728_pm_ops, mcp4728_suspend,
> + mcp4728_resume);
> +
> +static int mcp4728_init_channels_data(struct mcp4728_data *data)
> +{
> + u8 inbuf[MCP4728_READ_RESPONSE_LEN];
> + int ret;
> + unsigned int i;
> +
> + ret = i2c_master_recv(data->client, inbuf, MCP4728_READ_RESPONSE_LEN);
> + if (ret < 0) {
> + dev_err(&data->client->dev,
> + "failed to read mcp4728 conf. Err=%d\n", ret);
> + return ret;
> + } else if (ret != MCP4728_READ_RESPONSE_LEN) {
> + dev_err(&data->client->dev,
> + "failed to read mcp4728 conf. Wrong Response Len ret=%d\n",
> + ret);
> + return -EIO;
> + }
> +
> + for (i = 0; i < MCP4728_N_CHANNELS; i++) {
Unusual to read back existing values from the device rather than resetting it into a clean
state. What is your reasoning?
> + struct mcp4728_channel_data *ch = &data->channel_data[i];
> + u8 r2 = inbuf[i * 6 + 1];
> + u8 r3 = inbuf[i * 6 + 2];
> + u32 dac_mv;
> +
> + ch->dac_value = (r2 & 0x0F) << 8 | r3;
> + ch->ref_mode = (r2 & MCP4728_CMD_VREF_MASK) >> MCP4728_CMD_VREF_POS;
> + ch->pd_mode = (r2 & MCP4728_CMD_PDMODE_MASK) >> MCP4728_CMD_PDMODE_POS;
> + ch->g_mode = (r2 & MCP4728_CMD_GAIN_MASK) >> MCP4728_CMD_GAIN_POS;
Use FIELD_GET()
> +
> + if (ch->g_mode == MCP4728_GAIN_X2 && ch->ref_mode == MCP4728_VREF_EXTERNAL_VDD)
> + dev_warn(&data->client->dev,
> + "CH%d: Gain x2 not effective when vref is vdd",
> + i);
> +
> + dac_mv = mcp4728_raw_to_mV(ch->dac_value, i, data);
> + dev_info(&data->client->dev,
> + "CH%d: Voltage=%dmV VRef=%d PowerDown=%d Gain=%d\n", i,
> + dac_mv, ch->ref_mode, ch->pd_mode, ch->g_mode);
That's noise that you should be able to get by directly reading the relevant attributes
or is detail that userspace should not need to know about.
You can rely on dynamic debug though and make that dev_dbg() so it is available if needed.
> + }
> +
> + return 0;
> +}
> +
> +static int mcp4728_probe(struct i2c_client *client)
> +{
> + const struct i2c_device_id *id = i2c_client_get_device_id(client);
> + struct mcp4728_data *data;
> + struct iio_dev *indio_dev;
> + int err;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + data = iio_priv(indio_dev);
> + i2c_set_clientdata(client, indio_dev);
> + data->client = client;
> +
> + data->vdd_reg = devm_regulator_get(&client->dev, "vdd");
> + if (IS_ERR(data->vdd_reg))
> + return PTR_ERR(data->vdd_reg);
> +
> + err = regulator_enable(data->vdd_reg);
> + if (err)
> + goto err_disable_vdd_reg;
As mentioned below - a devm_add_action_or_reset() here to deal with
the regulator would be good. Also, regulator_enable() is side effect
free on error so you should not be disabling in this error path.
> +
> + err = mcp4728_init_channels_data(data);
> + if (err) {
> + dev_err(&client->dev,
> + "failed to read mcp4728 current configuration\n");
> + goto err_disable_vdd_reg;
> + }
> +
> + indio_dev->name = id->name;
> + indio_dev->info = &mcp4728_info;
> + indio_dev->channels = mcp4728_channels;
> + indio_dev->num_channels = MCP4728_N_CHANNELS;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + err = iio_device_register(indio_dev);
> + if (err)
> + goto err_disable_vdd_reg;
> +
> + return 0;
> +
> +err_disable_vdd_reg:
> + regulator_disable(data->vdd_reg);
> +
> + return err;
> +}
> +
> +static void mcp4728_remove(struct i2c_client *client)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
> + struct mcp4728_data *data = iio_priv(indio_dev);
> +
> + iio_device_unregister(indio_dev);
> + regulator_disable(data->vdd_reg);
Use devm_add_action_or_reset() + a suitable callback to turn of the
regulator, then you can use devm for the device register as well
and no need for a remove function or error handlers in probe()
> +}
> +
> +static const struct i2c_device_id mcp4728_id[] = {
> + { "mcp4728", MCP4728 },
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, mcp4728_id);
> +
> +static const struct of_device_id mcp4728_of_match[] = {
> + { .compatible = "microchip,mcp4728" },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mcp4728_of_match);
> +
> +static struct i2c_driver mcp4728_driver = {
> + .driver = {
> + .name = MCP4728_DRV_NAME,
> + .of_match_table = mcp4728_of_match,
> + .pm = pm_sleep_ptr(&mcp4728_pm_ops),
> + },
> + .probe = mcp4728_probe,
> + .remove = mcp4728_remove,
> + .id_table = mcp4728_id,
> +};
> +module_i2c_driver(mcp4728_driver);
> +
> +MODULE_AUTHOR("Andrea Collamati <andrea.collamati@xxxxxxxxx>");
> +MODULE_DESCRIPTION("MCP4728 12-bit DAC");
> +MODULE_LICENSE("GPL");
