On Thu, Jul 20, 2023 at 10:10 AM James Hilliard
<james.hilliard1@xxxxxxxxx> wrote:
> + reg_audio: regulator-audio {
> + compatible = "regulator-fixed";
> + regulator-name = "tlv320aic3x-supply";
> + enable-active-high;
There is no gpio associated, so 'enable-active-high' should be removed.
> + backlight_lvds: backlight-lvds {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 50000 0>;
> + brightness-levels = <0 4 8 16 32 64 128 248>;
> + default-brightness-level = <7>;
> + power-supply = <®_pu>;
Is this correct? reg_pu is an internal regulator and should supply the
internal SoC peripherals.
> + };
> +&iomuxc {
> + pinctrl_ipu1: ipu1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
> + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
> + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
> + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
> + MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x10
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
> + >;
> + };
> +
> + pinctrl_ipu1: ipu1grp {
pinctrl_ipu1 appears twice. This second entry should be pinctrl_camera
or something like that.
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
> + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
Move pinctrl_flexcan1 to keep the pinctrl entries sorted.
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "okay";
Add a new line.
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in_lvds0>;
> + };
> + };
> + };
> +
> + lvds-channel@1 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "okay";
Add a new line.
> + port@4 {
