Mango Pi MQ Quad is a H616 based SBC, add basic support for the board
and its peripherals
Signed-off-by: Matthew Croughan <matthew.croughan@xxxxxxx>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-mangopi-mq-quad.dts | 183 ++++++++++++++++++
2 files changed, 184 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6a96494a2e0a..06c5b97dbfc3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,5 +38,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-mangopi-mq-quad.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts
new file mode 100644
index 000000000000..dc1b88e0adae
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts
@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * Copyright (C) 2023 Matthew Croughan <matthew.croughan@xxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "MangoPi MQ-Quad";
+ compatible = "widora,mangopi-mq-quad", "allwinner,sun50i-h616";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ /* board wide 3V3 supply directly from SY8008 regulator */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 18 GPIO_ACTIVE_LOW>; /* PG18 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pc-supply = <®_vcc3v3>;
+ vcc-pg-supply = <®_vcc3v3>;
+ vcc-pi-supply = <®_vcc3v3>;
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ bus-width = <4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ pinctrl-0 = <&mmc1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ rtl8723ds: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 15 IRQ_TYPE_LEVEL_LOW>; /* PG15 */
+ interrupt-names = "host-wake";
+ };
+};
+
+
+&uart1 {
+ uart-has-rtscts;
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8723ds-bt";
+ device-wake-gpios = <&pio 6 17 GPIO_ACTIVE_HIGH>; /* PG17 */
+ enable-gpios = <&pio 6 19 GPIO_ACTIVE_HIGH>; /* PG19 */
+ host-wake-gpios = <&pio 6 16 GPIO_ACTIVE_HIGH>; /* PG16 */
+ };
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313a: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+ /* ALDO1 is feeding both VCC-PLL and VCC-DCXO, always-on is required,
+ * as removing power would cut the 1.8v supply for the RAM */
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-dram";
+ };
+
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc5v>;
+ status = "okay";
+};
--
2.41.0
