On 19/07/2023 18:00, James Hilliard wrote: > This patch adds support for the Variscite MX6 SoM Carrier Board. > > This Carrier-Board has the following : > - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display > - HDMI Connector > - USB Host + USB OTG Connector > - 10/100/1000 Mbps Ethernet > - miniPCI-Express slot > - SD Card connector > - Audio Headphone/Line In jack connectors > - S-ATA > - On-board DMIC > - RS485 Header > - CAN bus header > - SPI header > - Camera Interfaces header > - OnBoard RTC with Coin Backup battery socket > - RS232 Debug Header (IDC10) > - RS232 DTE > > Product Page : https://www.variscite.com/product/single-board-computers/var-mx6customboard > > The dts file based on the ones provided by Variscite on their own > kernel, but adapted for mainline. > > Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx> > Signed-off-by: James Hilliard <james.hilliard1@xxxxxxxxx> > --- > arch/arm/boot/dts/Makefile | 1 + > .../arm/boot/dts/imx6q-var-mx6customboard.dts | 291 ++++++++++++++++++ > 2 files changed, 292 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-var-mx6customboard.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 59829fc90315..9cfc3d3e91ea 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -665,6 +665,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-udoo.dtb \ > imx6q-utilite-pro.dtb \ > imx6q-var-dt6customboard.dtb \ > + imx6q-var-mx6customboard.dtb \ > imx6q-vicut1.dtb \ > imx6q-wandboard.dtb \ > imx6q-wandboard-revb1.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-var-mx6customboard.dts b/arch/arm/boot/dts/imx6q-var-mx6customboard.dts > new file mode 100644 > index 000000000000..47e39a6dc611 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-var-mx6customboard.dts > @@ -0,0 +1,291 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Support for Variscite MX6 Carrier-board > + * > + * Copyright 2016 Variscite, Ltd. All Rights Reserved > + * Copyright 2022 Bootlin > + */ > + > +/dts-v1/; > + > +#include "imx6qdl-var-som.dtsi" > +#include <dt-bindings/pwm/pwm.h> > + > +/ { > + model = "Variscite MX6 Custom Board"; Missing compatible. Missing bindings. > + > + reg_usb_otg_vbus: regulator-usb-otg-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > + > + reg_usb_h1_vbus: regulator-usb-h1-vbud { > + compatible = "regulator-fixed"; > + regulator-name = "usb_h1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > + > + reg_audio: regulator-audio { > + compatible = "regulator-fixed"; > + regulator-name = "tlv320aic3x-supply"; > + enable-active-high; > + }; > + > + panel0: lvds-panel0 { > + compatible = "panel-lvds"; > + backlight = <&backlight_lvds>; > + width-mm = <152>; > + height-mm = <91>; > + label = "etm070001adh6"; > + data-mapping = "jeida-18"; > + > + panel-timing { > + clock-frequency = <32000000>; > + hactive = <800>; > + vactive = <480>; > + hback-porch = <39>; > + hfront-porch = <39>; > + vback-porch = <29>; > + vfront-porch = <13>; > + hsync-len = <47>; > + vsync-len = <2>; > + }; Messed up indentation. > + > + port { > + panel_in_lvds0: endpoint { > + remote-endpoint = <&lvds0_out>; > + }; > + }; > + }; > + > + panel1: lvds-panel1 { > + compatible = "panel-lvds"; > + width-mm = <152>; > + height-mm = <91>; > + data-mapping = "jeida-18"; > + > + panel-timing { > + clock-frequency = <38251000>; > + hactive = <800>; Same problem. > + vactive = <600>; > + hback-porch = <112>; > + hfront-porch = <32>; > + vback-porch = <3>; > + vfront-porch = <17>; > + hsync-len = <80>; > + vsync-len = <4>; > + }; > + > + port { > + panel_in_lvds1: endpoint { > + remote-endpoint = <&lvds1_out>; > + }; > + }; > + }; > + > + backlight_lvds: backlight-lvds { > + compatible = "pwm-backlight"; > + pwms = <&pwm2 0 50000 0>; > + brightness-levels = <0 4 8 16 32 64 128 248>; > + default-brightness-level = <7>; > + status = "okay"; Drop status. Why do you need it? > + }; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > + > + touchscreen@24 { > + compatible = "cypress,tt21000"; > + reg = <0x24>; > + interrupt-parent = <&gpio3>; > + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; > + reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; > + touchscreen-size-x = <880>; > + touchscreen-size-y = <1280>; > + }; > + > + touchscreen@38 { > + compatible = "edt,edt-ft5x06"; > + reg = <0x38>; > + interrupt-parent = <&gpio3>; > + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; > + touchscreen-size-x = <1800>; > + touchscreen-size-y = <1000>; > + }; > +}; > + > +&iomuxc { > + imx6qdl-var-som-mx6 { > + Drop stray blank line > + pinctrl_ipu1: ipu1grp { > + fsl,pins = < > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 > + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 > + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 > + MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x80000000 > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 > + >; > + }; > + > + pinctrl_ipu1: ipu1grp { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000 > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000 > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000 > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000 > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000 > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000 > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000 > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000 > + MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x80000000 > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000 > + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000 > + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000 > + >; > + }; > + > + pinctrl_usbotg_var: usbotggrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x17059 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071 > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071 > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071 > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071 > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071 > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071 > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 > + >; > + }; > + > + pinctrl_flexcan1: flexcan1grp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x80000000 > + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x80000000 > + >; > + }; > + }; > +}; > + > +&mipi_csi { > + status = "okay"; > + ipu_id = <0>; > + csi_id = <1>; > + v_channel = <0>; > + lanes = <2>; > +}; > + > +&usbh1 { > + vbus-supply = <®_usb_h1_vbus>; > + status = "okay"; > +}; > + > +&ldb { > + status = "okay"; > + > + lvds-channel@0 { > + fsl,data-mapping = "spwg"; > + fsl,data-width = <24>; > + status = "okay"; Again, why do you need it? Is it disabled? > + primary; > + port@4 { > + reg = <4>; > + > + lvds0_out: endpoint { > + remote-endpoint = <&panel_in_lvds0>; > + }; > + }; > + }; > + > + lvds-channel@1 { > + fsl,data-mapping = "spwg"; > + fsl,data-width = <24>; > + status = "okay"; > + primary; > + port@4 { > + reg = <4>; > + > + lvds1_out: endpoint { > + remote-endpoint = <&panel_in_lvds1>; > + }; > + }; > + }; > +}; Best regards, Krzysztof
