Hi, Am Montag, 17. Juli 2023, 08:18:22 CEST schrieb Liu Ying: > Hi, > > This series aims to add MIPI DSI support for Freescale i.MX93 SoC. > > There is a Synopsys DesignWare MIPI DSI host controller and a Synopsys > Designware MIPI DPHY embedded in i.MX93. Some configurations and > extensions to them are controlled by i.MX93 media blk-ctrl. > > Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI > bridge helpers and implementing i.MX93 MIPI DSI specific extensions. > > Note that since this series touches the dw-mipi-dsi driver, tests are > needed to be done for meson, rockchip and stm. > > Patch 1 ~ 7 do preparation work for adding i.MX93 MIPI DSI DRM bridge > driver. > > Patch 8 adds DT-binding documentation for i.MX93 MIPI DSI. > > Patch 9 adds i.MX93 MIPI DSI DRM bridge. > > Liu Ying (9): > drm/bridge: synopsys: dw-mipi-dsi: Add dw_mipi_dsi_get_bridge() helper > drm/bridge: synopsys: dw-mipi-dsi: Add input bus format negotiation > support > drm/bridge: synopsys: dw-mipi-dsi: Force input bus flags > drm/bridge: synopsys: dw-mipi-dsi: Add mode fixup support > drm/bridge: synopsys: dw-mipi-dsi: Use pixel clock rate to calculate > lbcc > drm/bridge: synopsys: dw-mipi-dsi: Set minimum lane byte clock cycles > for HSA and HBP > drm/bridge: synopsys: dw-mipi-dsi: Disable HSTX and LPRX timeout check > dt-bindings: display: bridge: Document Freescale i.MX93 MIPI DSI > drm/bridge: imx: Add i.MX93 MIPI DSI support > > .../display/bridge/fsl,imx93-mipi-dsi.yaml | 115 +++ > drivers/gpu/drm/bridge/imx/Kconfig | 10 + > drivers/gpu/drm/bridge/imx/Makefile | 1 + > drivers/gpu/drm/bridge/imx/imx93-mipi-dsi.c | 934 ++++++++++++++++++ > drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 91 +- > include/drm/bridge/dw_mipi_dsi.h | 16 + > 6 files changed, 1163 insertions(+), 4 deletions(-) > create mode 100644 > Documentation/devicetree/bindings/display/bridge/fsl,imx93-mipi-dsi.yaml > create mode 100644 drivers/gpu/drm/bridge/imx/imx93-mipi-dsi.c Thanks for posting this patch series. I was trying to use this driver on our TQMa93xxLA platform where the DSI signals are connected to a TC9595 (driver tc358767) DSI-to-DP bridge. Unfortunately this bridge requires the DSI signals to be in LP-11 upon reset and while in idle, otherwise not even DP AUX channel is functional. Apparently DSI is currently not in LP-11. But reading the RM I have no idea how to configure the DSI host to achieve that. Do you have additional information which might help me here? Also could you provide your DT configuration? Thanks and best regards, Alexander -- TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany Amtsgericht München, HRB 105018 Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider http://www.tq-group.com/
