Re: [PATCH v17 17/20] PCI: rcar-gen4: Add R-Car Gen4 PCIe Host support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jul 14, 2023 at 02:21:52AM +0000, Yoshihiro Shimoda wrote:
> Hi Serge,
> 
> > From: Serge Semin, Sent: Wednesday, July 12, 2023 8:35 PM
> > 
> > On Wed, Jul 05, 2023 at 08:42:03PM +0900, Yoshihiro Shimoda wrote:
> > > Add R-Car Gen4 PCIe Host support. This controller is based on
> > > Synopsys DesignWare PCIe, but this controller has vendor-specific
> > > registers so that requires initialization code like mode setting
> > > and retraining and so on.
> > >
> > > To reduce code delta, adds some helper functions which are used by
> > > both the host driver and the endpoint driver (which is added
> > > immediately afterwards) into a separate file.
> > >
> > > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
> > > ---
> > >  drivers/pci/controller/dwc/Kconfig            |   9 +
> > >  drivers/pci/controller/dwc/Makefile           |   2 +
> > >  .../pci/controller/dwc/pcie-rcar-gen4-host.c  | 144 +++++++++++++
> > >  drivers/pci/controller/dwc/pcie-rcar-gen4.c   | 197 ++++++++++++++++++
> > >  drivers/pci/controller/dwc/pcie-rcar-gen4.h   |  43 ++++
> > >  5 files changed, 395 insertions(+)
> > >  create mode 100644 drivers/pci/controller/dwc/pcie-rcar-gen4-host.c
> > >  create mode 100644 drivers/pci/controller/dwc/pcie-rcar-gen4.c
> > >  create mode 100644 drivers/pci/controller/dwc/pcie-rcar-gen4.h
> > >
> > > diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> > > index ab96da43e0c2..64d4d37bc891 100644
> > > --- a/drivers/pci/controller/dwc/Kconfig
> > > +++ b/drivers/pci/controller/dwc/Kconfig
> > > @@ -415,4 +415,13 @@ config PCIE_VISCONTI_HOST
> > >  	  Say Y here if you want PCIe controller support on Toshiba Visconti SoC.
> > >  	  This driver supports TMPV7708 SoC.
> > >
> > > +config PCIE_RCAR_GEN4
> > > +	tristate "Renesas R-Car Gen4 PCIe Host controller"
> > > +	depends on ARCH_RENESAS || COMPILE_TEST
> > > +	depends on PCI_MSI
> > > +	select PCIE_DW_HOST
> > > +	help
> > > +	  Say Y here if you want PCIe host controller support on R-Car Gen4 SoCs.
> > > +	  This uses the DesignWare core.
> > > +
> > >  endmenu
> > > diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> > > index bf5c311875a1..486cf706b53d 100644
> > > --- a/drivers/pci/controller/dwc/Makefile
> > > +++ b/drivers/pci/controller/dwc/Makefile
> > > @@ -26,6 +26,8 @@ obj-$(CONFIG_PCIE_TEGRA194) += pcie-tegra194.o
> > >  obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
> > >  obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
> > >  obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
> > > +pcie-rcar-gen4-host-drv-objs := pcie-rcar-gen4.o pcie-rcar-gen4-host.o
> > > +obj-$(CONFIG_PCIE_RCAR_GEN4) += pcie-rcar-gen4-host-drv.o
> > >
> > >  # The following drivers are for devices that use the generic ACPI
> > >  # pci_root.c driver but don't support standard ECAM config access.
> > > diff --git a/drivers/pci/controller/dwc/pcie-rcar-gen4-host.c b/drivers/pci/controller/dwc/pcie-rcar-gen4-host.c
> > > new file mode 100644
> > > index 000000000000..e7c1eef792ec
> > > --- /dev/null
> > > +++ b/drivers/pci/controller/dwc/pcie-rcar-gen4-host.c
> > > @@ -0,0 +1,144 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * PCIe host controller driver for Renesas R-Car Gen4 Series SoCs
> > > + * Copyright (C) 2022-2023 Renesas Electronics Corporation
> > > + */
> > > +
> > > +#include <linux/delay.h>
> > > +#include <linux/interrupt.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/pci.h>
> > > +#include <linux/platform_device.h>
> > > +
> > > +#include "pcie-rcar-gen4.h"
> > > +#include "pcie-designware.h"
> > > +
> > > +static int rcar_gen4_pcie_host_init(struct dw_pcie_rp *pp)
> > > +{
> > > +	struct dw_pcie *dw = to_dw_pcie_from_pp(pp);
> > > +	struct rcar_gen4_pcie *rcar = to_rcar_gen4_pcie(dw);
> > > +	int ret;
> > > +	u32 val;
> > > +
> > > +	gpiod_set_value_cansleep(dw->pe_rst, 1);
> > > +
> > > +	ret = clk_bulk_prepare_enable(DW_PCIE_NUM_CORE_CLKS, dw->core_clks);
> > > +	if (ret) {
> > > +		dev_err(dw->dev, "Failed to enable ref clocks\n");
> > > +		return ret;
> > > +	}
> > > +
> > > +	ret = rcar_gen4_pcie_basic_init(rcar);
> > > +	if (ret < 0) {
> > > +		clk_bulk_disable_unprepare(DW_PCIE_NUM_CORE_CLKS, dw->core_clks);
> > > +		return ret;
> > > +	}
> > > +
> > > +	/*
> > > +	 * According to the section 3.5.7.2 "RC Mode" in DWC PCIe Dual Mode
> > > +	 * Rev.5.20a, we should disable two BARs to avoid unnecessary memory
> > > +	 * assignment during device enumeration.
> > > +	 */
> > > +	dw_pcie_writel_dbi2(dw, PCI_BASE_ADDRESS_0, 0x0);
> > > +	dw_pcie_writel_dbi2(dw, PCI_BASE_ADDRESS_1, 0x0);
> > > +
> > > +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> > > +		/* Enable MSI interrupt signal */
> > > +		val = readl(rcar->base + PCIEINTSTS0EN);
> > > +		val |= MSI_CTRL_INT;
> > > +		writel(val, rcar->base + PCIEINTSTS0EN);
> > > +	}
> > > +
> > > +	msleep(100);	/* pe_rst requires 100msec delay */
> > > +
> > > +	gpiod_set_value_cansleep(dw->pe_rst, 0);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static const struct dw_pcie_host_ops rcar_gen4_pcie_host_ops = {
> > > +	.host_init = rcar_gen4_pcie_host_init,
> > > +};
> > > +
> > > +static int rcar_gen4_add_dw_pcie_rp(struct rcar_gen4_pcie *rcar,
> > 
> > > +				   struct platform_device *pdev)
> > 
> > The argument is unused. What about dropping it?
> 
> You're correct. I'll drop it on v18.
> 
> > > +{

> > > +	struct dw_pcie *dw = &rcar->dw;
> > > +	struct dw_pcie_rp *pp = &dw->pp;

BTW, this can be wrapper to just:
+struct dw_pcie_rp *pp = &rcar->dw.pp;
seeing you aren't using pointer to dw_pcie here.

> > > +
> > > +	pp->num_vectors = MAX_MSI_IRQS;
> > > +	pp->ops = &rcar_gen4_pcie_host_ops;
> > > +
> > > +	return dw_pcie_host_init(pp);
> > > +}
> > > +
> > > +static void rcar_gen4_remove_dw_pcie_rp(struct rcar_gen4_pcie *rcar)
> > > +{
> > > +	dw_pcie_host_deinit(&rcar->dw.pp);
> > > +	gpiod_set_value_cansleep(rcar->dw.pe_rst, 1);
> > > +}
> > > +
> > > +static int rcar_gen4_pcie_probe(struct platform_device *pdev)
> > > +{
> > > +	struct device *dev = &pdev->dev;
> > > +	struct rcar_gen4_pcie *rcar;
> > > +	int err;
> > > +
> > > +	rcar = rcar_gen4_pcie_devm_alloc(dev);
> > > +	if (!rcar)
> > > +		return -ENOMEM;
> > > +
> > > +	err = rcar_gen4_pcie_get_resources(rcar, pdev);
> > > +	if (err < 0) {
> > > +		dev_err(dev, "Failed to request resource: %d\n", err);
> > > +		return err;
> > > +	}
> > > +
> > 
> > > +	platform_set_drvdata(pdev, rcar);
> > 
> > This could have been moved to rcar_gen4_pcie_devm_alloc(). But see my
> > last comment first.
> 
> I think so.
> 
> > > +
> > > +	err = rcar_gen4_pcie_prepare(rcar);
> > > +	if (err < 0)
> > > +		return err;
> > > +
> > 
> > > +	rcar->mode = DW_PCIE_RC_TYPE;
> > 
> > What about moving this to the rcar_gen4_add_dw_pcie_rp() method? Thus
> > it will look similar to the rcar_gen4_add_pcie_ep() method you
> > implemented in the Rcar Gen4 EP driver.
> 
> Yes. I'll move this to the rcar_gen4_add_dw_pcie_rp().
> 
> > > +	err = rcar_gen4_add_dw_pcie_rp(rcar, pdev);
> > > +	if (err < 0)
> > > +		goto err_add;
> > > +
> > > +	return 0;
> > > +
> > > +err_add:
> > > +	rcar_gen4_pcie_unprepare(rcar);
> > > +
> > > +	return err;
> > > +}
> > > +
> > 
> > > +static int rcar_gen4_pcie_remove(struct platform_device *pdev)
> > > +{
> > > +	struct rcar_gen4_pcie *rcar = platform_get_drvdata(pdev);
> > > +
> > > +	rcar_gen4_remove_dw_pcie_rp(rcar);
> > > +	rcar_gen4_pcie_unprepare(rcar);
> > > +
> > > +	return 0;
> > > +}
> > 
> > Please convert this function to returning void and assign to the
> > platform_driver.remove_new pointer instead.
> 
> I got it.
> 
> > > +
> > > +static const struct of_device_id rcar_gen4_pcie_of_match[] = {
> > > +	{ .compatible = "renesas,rcar-gen4-pcie", },
> > > +	{},
> > > +};
> > > +
> > > +static struct platform_driver rcar_gen4_pcie_driver = {
> > > +	.driver = {
> > > +		.name = "pcie-rcar-gen4",
> > > +		.of_match_table = rcar_gen4_pcie_of_match,
> > > +		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
> > > +	},
> > > +	.probe = rcar_gen4_pcie_probe,
> > 
> > > +	.remove = rcar_gen4_pcie_remove,
> > 
> > ditto
> 
> I'll fix this.
> 
> > > +};
> > > +module_platform_driver(rcar_gen4_pcie_driver);
> > > +
> > > +MODULE_DESCRIPTION("Renesas R-Car Gen4 PCIe host controller driver");
> > > +MODULE_LICENSE("GPL");
> > > diff --git a/drivers/pci/controller/dwc/pcie-rcar-gen4.c b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
> > > new file mode 100644
> > > index 000000000000..2cd5c17c1695
> > > --- /dev/null
> > > +++ b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
> > > @@ -0,0 +1,197 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * PCIe host/endpoint controller driver for Renesas R-Car Gen4 Series SoCs
> > > + * Copyright (C) 2022-2023 Renesas Electronics Corporation
> > > + */
> > > +
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/pci.h>
> > > +#include <linux/pm_runtime.h>
> > > +#include <linux/reset.h>
> > > +
> > > +#include "pcie-rcar-gen4.h"
> > > +#include "pcie-designware.h"
> > > +
> > > +/* Renesas-specific */
> > > +#define PCIERSTCTRL1		0x0014
> > > +#define  APP_HOLD_PHY_RST	BIT(16)
> > > +#define  APP_LTSSM_ENABLE	BIT(0)
> > > +
> > > +#define RCAR_NUM_SPEED_CHANGE_RETRIES	10
> > > +#define RCAR_MAX_LINK_SPEED		4
> > > +
> > > +static void rcar_gen4_pcie_ltssm_enable(struct rcar_gen4_pcie *rcar,
> > > +					bool enable)
> > > +{
> > > +	u32 val;
> > > +
> > > +	val = readl(rcar->base + PCIERSTCTRL1);
> > > +	if (enable) {
> > > +		val |= APP_LTSSM_ENABLE;
> > > +		val &= ~APP_HOLD_PHY_RST;
> > > +	} else {
> > > +		/*
> > > +		 * Since the datasheet of R-Car doesn't mention how to assert
> > > +		 * the APP_HOLD_PHY_RST, don't assert it again. Otherwise,
> > > +		 * hang-up issue happened in the dw_edma_core_off() when
> > > +		 * the controller didn't detect a PCI device.
> > > +		 */
> > > +		val &= ~APP_LTSSM_ENABLE;
> > > +	}
> > > +	writel(val, rcar->base + PCIERSTCTRL1);
> > > +}
> > > +
> > > +static int rcar_gen4_pcie_link_up(struct dw_pcie *dw)
> > > +{
> > > +	struct rcar_gen4_pcie *rcar = to_rcar_gen4_pcie(dw);
> > > +	u32 val, mask;
> > > +
> > > +	val = readl(rcar->base + PCIEINTSTS0);
> > > +	mask = RDLH_LINK_UP | SMLH_LINK_UP;
> > > +
> > > +	return (val & mask) == mask;
> > > +}
> > > +
> > > +static bool rcar_gen4_pcie_speed_change(struct dw_pcie *dw)
> > > +{
> > > +	u32 val;
> > > +	int i;
> > > +
> > > +	val = dw_pcie_readl_dbi(dw, PCIE_LINK_WIDTH_SPEED_CONTROL);
> > > +	val &= ~PORT_LOGIC_SPEED_CHANGE;
> > > +	dw_pcie_writel_dbi(dw, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
> > > +
> > > +	val = dw_pcie_readl_dbi(dw, PCIE_LINK_WIDTH_SPEED_CONTROL);
> > > +	val |= PORT_LOGIC_SPEED_CHANGE;
> > > +	dw_pcie_writel_dbi(dw, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
> > > +
> > > +	for (i = 0; i < RCAR_NUM_SPEED_CHANGE_RETRIES; i++) {
> > > +		val = dw_pcie_readl_dbi(dw, PCIE_LINK_WIDTH_SPEED_CONTROL);
> > > +		if (!(val & PORT_LOGIC_SPEED_CHANGE))
> > > +			return true;
> > > +		usleep_range(10000, 11000);
> > > +	}
> > > +
> > > +	return false;
> > > +}
> > > +
> > > +static int rcar_gen4_pcie_start_link(struct dw_pcie *dw)
> > > +{
> > > +	struct rcar_gen4_pcie *rcar = to_rcar_gen4_pcie(dw);
> > > +	int i, changes;
> > > +
> > > +	rcar_gen4_pcie_ltssm_enable(rcar, true);
> > > +
> > > +	/*
> > > +	 * Require direct speed change with retrying here if the link_gen is
> > 
> > > +	 * PCIe Gen2 or later.
> > 
> > s/later/higher
> 
> I'll fix this.
> 
> > > +	 */
> > > +	changes = min_not_zero(dw->link_gen, RCAR_MAX_LINK_SPEED) - 1;
> > > +
> > > +	/*
> > > +	 * Since dw_pcie_setup_rc() sets it once, PCIe Gen2 will be trained.
> > 
> > > +	 * So, this needs remaining times for PCIe Gen4 if RC mode.
> > 
> > For "_up to_ PCIe Gen4", isn't it? Because AFAIR PCIe Gen3 will need
> > to have one changes-iteration for RC mode.
> 
> You're correct. I'll fix it.
> 
> > > +	 */
> > > +	if (changes && rcar->mode == DW_PCIE_RC_TYPE)
> > > +		changes--;
> > > +
> > > +	for (i = 0; i < changes; i++) {
> > > +		if (!rcar_gen4_pcie_speed_change(dw))
> > > +			break;	/* No error because possible disconnected here if EP mode */
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static void rcar_gen4_pcie_stop_link(struct dw_pcie *dw)
> > > +{
> > > +	struct rcar_gen4_pcie *rcar = to_rcar_gen4_pcie(dw);
> > > +
> > > +	rcar_gen4_pcie_ltssm_enable(rcar, false);
> > > +}
> > > +
> > > +int rcar_gen4_pcie_basic_init(struct rcar_gen4_pcie *rcar)
> > > +{
> > > +	struct dw_pcie *dw = &rcar->dw;
> > > +	u32 val;
> > > +
> > > +	if (!reset_control_status(dw->core_rsts[DW_PCIE_PWR_RST].rstc))
> > > +		reset_control_assert(dw->core_rsts[DW_PCIE_PWR_RST].rstc);
> > > +
> > > +	val = readl(rcar->base + PCIEMSR0);
> > > +	if (rcar->mode == DW_PCIE_RC_TYPE)
> > > +		val |= DEVICE_TYPE_RC;
> > > +	else if (rcar->mode == DW_PCIE_EP_TYPE)
> > > +		val |= DEVICE_TYPE_EP;
> > > +	else
> > > +		return -EINVAL;
> > > +
> > > +	if (dw->num_lanes < 4)
> > > +		val |= BIFUR_MOD_SET_ON;
> > > +
> > > +	writel(val, rcar->base + PCIEMSR0);
> > > +
> > > +	return reset_control_deassert(dw->core_rsts[DW_PCIE_PWR_RST].rstc);
> > > +}
> > > +
> > > +int rcar_gen4_pcie_prepare(struct rcar_gen4_pcie *rcar)
> > > +{
> > > +	struct device *dev = rcar->dw.dev;
> > > +	int err;
> > > +
> > > +	pm_runtime_enable(dev);
> > > +	err = pm_runtime_resume_and_get(dev);
> > > +	if (err < 0) {
> > > +		dev_err(dev, "Failed to resume/get Runtime PM\n");
> > > +		pm_runtime_disable(dev);
> > > +	}
> > > +
> > 
> > > +	dw_pcie_cap_set(&rcar->dw, REQ_RES);
> > 
> > Hmm, why is this here? Isn't it more appropriate to have it in
> > rcar_gen4_pcie_devm_alloc() together with the EDMA_UNROLL flag
> > setting? REQ_RES flag indicates a request for the driver core to get
> > the generic DW PCIe RP/EP resources. It doesn't look as being
> > suitable to be set in a prepare()-like method.
> 
> I don't have a special reason.. So, I'll move this to
> the rcar_gen4_pcie_devm_alloc().
> 
> > > +
> > > +	return err;
> > > +}
> > > +
> > > +void rcar_gen4_pcie_unprepare(struct rcar_gen4_pcie *rcar)
> > > +{
> > > +	struct device *dev = rcar->dw.dev;
> > > +	struct dw_pcie *dw = &rcar->dw;
> > > +
> > 
> > > +	if (!reset_control_status(dw->core_rsts[DW_PCIE_PWR_RST].rstc))
> > > +		reset_control_assert(dw->core_rsts[DW_PCIE_PWR_RST].rstc);
> > 
> > The de-assertion is performed in rcar_gen4_pcie_basic_init() which is
> > called from the host_init() method. The respective antagonist is
> > supposed to be performed in the host_deinit() in order to revert the
> > changes on any error spotted in the host_init() and have a fully
> > cleaned up device on the remove() procedure. Having something like
> > rcar_gen4_pcie_basic_deinit() for it seems suitable.
> > 
> > BTW I would have added dw->pe_rst assertion to
> > dw_pcie_host_ops.host_deinit() too.
> 
> I understood it. I'll fix it.
> 
> > > +	pm_runtime_put(dev);
> > > +	pm_runtime_disable(dev);
> > > +}
> > > +
> > > +int rcar_gen4_pcie_get_resources(struct rcar_gen4_pcie *rcar,
> > > +				 struct platform_device *pdev)
> > > +{
> > > +	/* Renesas-specific registers */
> > > +	rcar->base = devm_platform_ioremap_resource_byname(pdev, "app");
> > > +	if (IS_ERR(rcar->base))
> > > +		return PTR_ERR(rcar->base);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static const struct dw_pcie_ops dw_pcie_ops = {
> > > +	.start_link = rcar_gen4_pcie_start_link,
> > > +	.stop_link = rcar_gen4_pcie_stop_link,
> > > +	.link_up = rcar_gen4_pcie_link_up,
> > > +};
> > > +
> > > +struct rcar_gen4_pcie *rcar_gen4_pcie_devm_alloc(struct device *dev)
> > > +{
> > > +	struct rcar_gen4_pcie *rcar;
> > > +
> > > +	rcar = devm_kzalloc(dev, sizeof(*rcar), GFP_KERNEL);
> > > +	if (!rcar)
> > > +		return NULL;
> > > +
> > > +	rcar->dw.dev = dev;
> > > +	rcar->dw.ops = &dw_pcie_ops;
> > > +	dw_pcie_cap_set(&rcar->dw, EDMA_UNROLL);
> > > +
> > > +	return rcar;
> > > +}
> > > diff --git a/drivers/pci/controller/dwc/pcie-rcar-gen4.h b/drivers/pci/controller/dwc/pcie-rcar-gen4.h
> > > new file mode 100644
> > > index 000000000000..e9cb816b33fa
> > > --- /dev/null
> > > +++ b/drivers/pci/controller/dwc/pcie-rcar-gen4.h
> > > @@ -0,0 +1,43 @@
> > > +/* SPDX-License-Identifier: GPL-2.0-only */
> > > +/*
> > > + * PCIe host/endpoint controller driver for Renesas R-Car Gen4 Series SoCs
> > > + * Copyright (C) 2022-2023 Renesas Electronics Corporation
> > > + */
> > > +
> > > +#ifndef _PCIE_RCAR_GEN4_H_
> > > +#define _PCIE_RCAR_GEN4_H_
> > > +
> > > +#include <linux/io.h>
> > > +#include <linux/pci.h>
> > > +
> > > +#include "pcie-designware.h"
> > > +
> > > +/* Renesas-specific */
> > > +#define PCIEMSR0		0x0000
> > > +#define  BIFUR_MOD_SET_ON	BIT(0)
> > > +#define  DEVICE_TYPE_EP		0
> > > +#define  DEVICE_TYPE_RC		BIT(4)
> > > +
> > > +#define PCIEINTSTS0		0x0084
> > > +#define PCIEINTSTS0EN		0x0310
> > > +#define  MSI_CTRL_INT		BIT(26)
> > > +#define  SMLH_LINK_UP		BIT(7)
> > > +#define  RDLH_LINK_UP		BIT(6)
> > > +#define PCIEDMAINTSTSEN		0x0314
> > > +#define  PCIEDMAINTSTSEN_INIT	GENMASK(15, 0)
> > > +
> > > +struct rcar_gen4_pcie {
> > > +	enum dw_pcie_device_mode mode;
> > 
> > > +	struct dw_pcie dw;
> > 
> > By moving this field to the head of the structure you'll have a
> > zero offset dw field with respect to the base-address of the
> > container. This will convert the container_of() macro to the just
> > type-cast.
> 
> I'll move it.
> 
> > > +	void __iomem *base;
> > > +};
> > 
> > > +#define to_rcar_gen4_pcie(x)	dev_get_drvdata((x)->dev)
> > 
> > Why? You have dw_pcie instance embedded into the rcar_gen4_pcie
> > structure. What about using the container_of() pattern then?
> > +#define to_rcar_gen4_pcie(_dw) container_of(_dw, struct rcar_gen4_pcie, dw)
> 

> This is because almost other drivers in drivers/pci/controller/dwc/ use dev_get_drvdata().
> I believe either way is fine.

It doesn't mean they are doing that correctly in all the cases.

In fact more than half of the DW PCIe vendor drivers keep a pointer to
the dw_pcie structure in the driver private data structure and perform
two allocations: one to get a private data instance and another one to
get the dw_pcie structure instance. Then they have no other way but to
use the generic device driver data pointer to retain the pointer to
the private data instance and then use the dev_get_drvdata() to
retrieve a pointer to their vendor-specific data.

Such pattern is redundant if you have the dw_pcie structure embedded
into the driver private data structure especially seeing all the DW
PCIe core driver operations pass the DW PCIe RP/EP data pointers. It
makes you free from the double allocations and let you get to your
private data pointer as long as the pointer to the dw_pcie available
(it's the case for all the DW PCIe core driver callbacks) with no need
in using the generic device pointer at all.

Regarding the rest of the drivers. Some of them using the
container_of()-based pattern (including mine), but the rest (Rockchip,
fu740, Qcom, Uniphier, Visconti, Exynos, Meson) are using an
intermixed version of the patterns described above. IMO it's not
right. If I were the core driver maintainer I would have converted
them to being more concise in that regard. It would be even more
correct to convert all the LLDDs to using the container_of()-pattern
where it's appropriate.

-Serge(y)

> 
> > > +
> > > +int rcar_gen4_pcie_basic_init(struct rcar_gen4_pcie *rcar);
> > 
> > > +int rcar_gen4_pcie_prepare(struct rcar_gen4_pcie *pcie);
> > > +void rcar_gen4_pcie_unprepare(struct rcar_gen4_pcie *pcie);
> > 
> > s/pcie/rcar
> 
> I'll fix it.
> 
> > > +int rcar_gen4_pcie_get_resources(struct rcar_gen4_pcie *rcar,
> > 
> > > +				 struct platform_device *pdev);
> > > +struct rcar_gen4_pcie *rcar_gen4_pcie_devm_alloc(struct device *dev);
> > 
> > Just a general note you may find useful. If I were you I would have
> > added struct platform_device *pdev field to struct rcar_gen4_pcie and
> > initialized it in the rcar_gen4_pcie_devm_alloc() method (it shall
> > accept the platform_device pointer argument instead of just device).
> > Thus you'll always have the {platform_}device pointer around as soon
> > as you have the rcar_gen4_pcie pointer available which much more
> > common case in the most of LLDD. This will greatly simplify any
> > possible driver updates in future. Moreover you won't need to pass an
> > additional device-pointer to the methods defined in your driver. For
> > instance, in that case the rcar_gen4_pcie_get_resources() will need to
> > accept just rcar_gen4_pcie pointer. Thus it will look unified aside
> > with the rest of the methods in your driver.
> 
> Thank you for your suggestion. I think so. So, I'll fix it.
> 
> Best regards,
> Yoshihiro Shimoda
> 
> > -Serge(y)
> > 
> > > +
> > > +#endif /* _PCIE_RCAR_GEN4_H_ */
> > > --
> > > 2.25.1
> > >



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux