[PATCH V2 1/2] arm64: dts: qcom: ipq9574: Add common RDP dtsi file

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add a dtsi file to include interfaces that are common
across RDPs.

Signed-off-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
---
 Changes in V2:
	- RDP418 and RDP433 supports shdc. Removed sdhc related nodes
	  from common dtsi and added to corresponding rdp dts.
	- Moved USB and regulator related nodes to common.dtsi.
	- Updated rdp454 dts to use common.dtsi.

 .../boot/dts/qcom/ipq9574-rdp-common.dtsi     | 125 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts   |  67 +---------
 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts   |  95 +------------
 arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts   |  65 +--------
 arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts   |  65 +--------
 arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts   |  66 +--------
 6 files changed, 134 insertions(+), 349 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
new file mode 100644
index 000000000000..40a7aefd0540
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 RDP board common device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq9574.dtsi"
+
+/ {
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	regulator_fixed_3p3: s3300 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-name = "fixed_3p3";
+	};
+
+	regulator_fixed_0p925: s0925 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <925000>;
+		regulator-max-microvolt = <925000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-name = "fixed_0p925";
+	};
+};
+
+&blsp1_spi0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&blsp1_uart2 {
+	pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-mp5496-regulators";
+
+		ipq9574_s1: s1 {
+		/*
+		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
+		 * During regulator registration, kernel not knowing the initial voltage,
+		 * considers it as zero and brings up the regulators with minimum supported voltage.
+		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
+		 * the regulators are brought up with 725mV which is sufficient for all the
+		 * corner parts to operate at 800MHz
+		 */
+			regulator-min-microvolt = <725000>;
+			regulator-max-microvolt = <1075000>;
+		};
+
+		mp5496_l2: l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	spi_0_pins: spi-0-state {
+		pins = "gpio11", "gpio12", "gpio13", "gpio14";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};
+
+&usb_0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_0_qmpphy {
+	vdda-pll-supply = <&mp5496_l2>;
+	vdda-phy-supply = <&regulator_fixed_0p925>;
+
+	status = "okay";
+};
+
+&usb_0_qusbphy {
+	vdd-supply = <&regulator_fixed_0p925>;
+	vdda-pll-supply = <&mp5496_l2>;
+	vdda-phy-dpdm-supply = <&regulator_fixed_3p3>;
+
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
index 2b093e02637b..ceb83c010c33 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
@@ -8,58 +8,12 @@
 
 /dts-v1/;
 
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C2";
 	compatible = "qcom,ipq9574-ap-al02-c2", "qcom,ipq9574";
 
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&blsp1_spi0 {
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	flash@0 {
-		compatible = "micron,n25q128a11", "jedec,spi-nor";
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&blsp1_uart2 {
-	pinctrl-0 = <&uart2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-mp5496-regulators";
-
-		ipq9574_s1: s1 {
-		/*
-		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
-		 * During regulator registration, kernel not knowing the initial voltage,
-		 * considers it as zero and brings up the regulators with minimum supported voltage.
-		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
-		 * the regulators are brought up with 725mV which is sufficient for all the
-		 * corner parts to operate at 800MHz
-		 */
-			regulator-min-microvolt = <725000>;
-			regulator-max-microvolt = <1075000>;
-		};
-	};
 };
 
 &sdhc_1 {
@@ -74,10 +28,6 @@
 	status = "okay";
 };
 
-&sleep_clk {
-	clock-frequency = <32000>;
-};
-
 &tlmm {
 	sdc_default_state: sdc-default-state {
 		clk-pins {
@@ -96,8 +46,8 @@
 
 		data-pins {
 			pins = "gpio0", "gpio1", "gpio2",
-			       "gpio3", "gpio6", "gpio7",
-			       "gpio8", "gpio9";
+				"gpio3", "gpio6", "gpio7",
+				"gpio8", "gpio9";
 			function = "sdc_data";
 			drive-strength = <8>;
 			bias-pull-up;
@@ -110,15 +60,4 @@
 			bias-pull-down;
 		};
 	};
-
-	spi_0_pins: spi-0-state {
-		pins = "gpio11", "gpio12", "gpio13", "gpio14";
-		function = "blsp0_spi";
-		drive-strength = <8>;
-		bias-disable;
-	};
-};
-
-&xo_board_clk {
-	clock-frequency = <24000000>;
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 877026ccc6e2..7685176f90ef 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -8,69 +8,11 @@
 
 /dts-v1/;
 
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7";
 	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	regulator_fixed_3p3: s3300 {
-		compatible = "regulator-fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-		regulator-name = "fixed_3p3";
-	};
-
-	regulator_fixed_0p925: s0925 {
-		compatible = "regulator-fixed";
-		regulator-min-microvolt = <925000>;
-		regulator-max-microvolt = <925000>;
-		regulator-boot-on;
-		regulator-always-on;
-		regulator-name = "fixed_0p925";
-	};
-};
-
-&blsp1_uart2 {
-	pinctrl-0 = <&uart2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-mp5496-regulators";
-
-		ipq9574_s1: s1 {
-		/*
-		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
-		 * During regulator registration, kernel not knowing the initial voltage,
-		 * considers it as zero and brings up the regulators with minimum supported voltage.
-		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
-		 * the regulators are brought up with 725mV which is sufficient for all the
-		 * corner parts to operate at 800MHz
-		 */
-			regulator-min-microvolt = <725000>;
-			regulator-max-microvolt = <1075000>;
-		};
-
-		mp5496_l2: l2 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
-	};
 };
 
 &sdhc_1 {
@@ -85,10 +27,6 @@
 	status = "okay";
 };
 
-&sleep_clk {
-	clock-frequency = <32000>;
-};
-
 &tlmm {
 	sdc_default_state: sdc-default-state {
 		clk-pins {
@@ -107,8 +45,8 @@
 
 		data-pins {
 			pins = "gpio0", "gpio1", "gpio2",
-			       "gpio3", "gpio6", "gpio7",
-			       "gpio8", "gpio9";
+				"gpio3", "gpio6", "gpio7",
+				"gpio8", "gpio9";
 			function = "sdc_data";
 			drive-strength = <8>;
 			bias-pull-up;
@@ -122,30 +60,3 @@
 		};
 	};
 };
-
-&usb_0_dwc3 {
-	dr_mode = "host";
-};
-
-&usb_0_qmpphy {
-	vdda-pll-supply = <&mp5496_l2>;
-	vdda-phy-supply = <&regulator_fixed_0p925>;
-
-	status = "okay";
-};
-
-&usb_0_qusbphy {
-	vdd-supply = <&regulator_fixed_0p925>;
-	vdda-pll-supply = <&mp5496_l2>;
-	vdda-phy-dpdm-supply = <&regulator_fixed_3p3>;
-
-	status = "okay";
-};
-
-&usb3 {
-	status = "okay";
-};
-
-&xo_board_clk {
-	clock-frequency = <24000000>;
-};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
index c8fa54e1a62c..d36d1078763e 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
@@ -8,73 +8,10 @@
 
 /dts-v1/;
 
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C6";
 	compatible = "qcom,ipq9574-ap-al02-c6", "qcom,ipq9574";
 
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&blsp1_spi0 {
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	flash@0 {
-		compatible = "micron,n25q128a11", "jedec,spi-nor";
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&blsp1_uart2 {
-	pinctrl-0 = <&uart2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-mp5496-regulators";
-
-		ipq9574_s1: s1 {
-		/*
-		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
-		 * During regulator registration, kernel not knowing the initial voltage,
-		 * considers it as zero and brings up the regulators with minimum supported voltage.
-		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
-		 * the regulators are brought up with 725mV which is sufficient for all the
-		 * corner parts to operate at 800MHz
-		 */
-			regulator-min-microvolt = <725000>;
-			regulator-max-microvolt = <1075000>;
-		};
-	};
-};
-
-&sleep_clk {
-	clock-frequency = <32000>;
-};
-
-&tlmm {
-	spi_0_pins: spi-0-state {
-		pins = "gpio11", "gpio12", "gpio13", "gpio14";
-		function = "blsp0_spi";
-		drive-strength = <8>;
-		bias-disable;
-	};
-};
-
-&xo_board_clk {
-	clock-frequency = <24000000>;
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
index f01de6628c3b..c30c9fbedf26 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
@@ -8,73 +8,10 @@
 
 /dts-v1/;
 
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C8";
 	compatible = "qcom,ipq9574-ap-al02-c8", "qcom,ipq9574";
 
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&blsp1_spi0 {
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	flash@0 {
-		compatible = "micron,n25q128a11", "jedec,spi-nor";
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&blsp1_uart2 {
-	pinctrl-0 = <&uart2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-mp5496-regulators";
-
-		ipq9574_s1: s1 {
-		/*
-		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
-		 * During regulator registration, kernel not knowing the initial voltage,
-		 * considers it as zero and brings up the regulators with minimum supported voltage.
-		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
-		 * the regulators are brought up with 725mV which is sufficient for all the
-		 * corner parts to operate at 800MHz
-		 */
-			regulator-min-microvolt = <725000>;
-			regulator-max-microvolt = <1075000>;
-		};
-	};
-};
-
-&sleep_clk {
-	clock-frequency = <32000>;
-};
-
-&tlmm {
-	spi_0_pins: spi-0-state {
-		pins = "gpio11", "gpio12", "gpio13", "gpio14";
-		function = "blsp0_spi";
-		drive-strength = <8>;
-		bias-disable;
-	};
-};
-
-&xo_board_clk {
-	clock-frequency = <24000000>;
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts
index 6efae3426cb8..0dc382f5d5ec 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts
@@ -8,73 +8,9 @@
 
 /dts-v1/;
 
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9";
 	compatible = "qcom,ipq9574-ap-al02-c9", "qcom,ipq9574";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&blsp1_spi0 {
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	flash@0 {
-		compatible = "micron,n25q128a11", "jedec,spi-nor";
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&blsp1_uart2 {
-	pinctrl-0 = <&uart2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-mp5496-regulators";
-
-		ipq9574_s1: s1 {
-		/*
-		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
-		 * During regulator registration, kernel not knowing the initial voltage,
-		 * considers it as zero and brings up the regulators with minimum supported voltage.
-		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
-		 * the regulators are brought up with 725mV which is sufficient for all the
-		 * corner parts to operate at 800MHz
-		 */
-			regulator-min-microvolt = <725000>;
-			regulator-max-microvolt = <1075000>;
-		};
-	};
-};
-
-&sleep_clk {
-	clock-frequency = <32000>;
-};
-
-&tlmm {
-	spi_0_pins: spi-0-state {
-		pins = "gpio11", "gpio12", "gpio13", "gpio14";
-		function = "blsp0_spi";
-		drive-strength = <8>;
-		bias-disable;
-	};
-};
-
-&xo_board_clk {
-	clock-frequency = <24000000>;
 };
-- 
2.17.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux