On 7/12/2023 5:54 PM, Dmitry Baryshkov wrote:
On 12/07/2023 14:35, Praveenkumar I wrote:
IPQ5332 has tsens v2.3.3 peripheral. This patch adds the tsense
node with nvmem cells for calibration data.
Signed-off-by: Praveenkumar I <quic_ipkumar@xxxxxxxxxxx>
---
[v2]:
Included qfprom nodes only for available sensors and removed
the offset suffix.
arch/arm64/boot/dts/qcom/ipq5332.dtsi | 66 +++++++++++++++++++++++++++
1 file changed, 66 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
index 8bfc2db44624..0eef77e36609 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
@@ -150,6 +150,46 @@ qfprom: efuse@a4000 {
reg = <0x000a4000 0x721>;
#address-cells = <1>;
#size-cells = <1>;
+
+ tsens_mode: mode@3e1 {
+ reg = <0x3e1 0x1>;
+ bits = <0 3>;
+ };
+
+ tsens_base0: base0@3e1 {
+ reg = <0x3e1 0x2>;
+ bits = <3 10>;
+ };
+
+ tsens_base1: base1@3e2 {
+ reg = <0x3e2 0x2>;
+ bits = <5 10>;
+ };
+
+ s11: s11@3a5 {
+ reg = <0x3a5 0x1>;
+ bits = <4 4>;
+ };
+
+ s12: s12@3a6 {
+ reg = <0x3a6 0x1>;
+ bits = <0 4>;
+ };
+
+ s13: s13@3a6 {
+ reg = <0x3a6 0x1>;
+ bits = <4 4>;
+ };
+
+ s14: s14@3ad {
+ reg = <0x3ad 0x2>;
+ bits = <7 4>;
+ };
+
+ s15: s15@3ae {
+ reg = <0x3ae 0x1>;
+ bits = <3 4>;
+ };
};
rng: rng@e3000 {
@@ -159,6 +199,32 @@ rng: rng@e3000 {
clock-names = "core";
};
+ tsens: thermal-sensor@4a9000 {
+ compatible = "qcom,ipq5332-tsens";
+ reg = <0x4a9000 0x1000>,
+ <0x4a8000 0x1000>;
+ nvmem-cells = <&tsens_mode>,
+ <&tsens_base0>,
+ <&tsens_base1>,
+ <&s11>,
+ <&s12>,
+ <&s13>,
+ <&s14>,
+ <&s15>;
+ nvmem-cell-names = "mode",
+ "base0",
+ "base1",
+ "s11",
+ "s12",
+ "s13",
+ "s14",
+ "s15";
Previously you had data for other sensors here. Are they not used at
all, not wired, have no known-good placement? I think it might be
better to declare all sensors here (and in the driver too) and then
consider enabling only a pile of them in the thermal-zone node.
Remaining sensors are not used at all. It is not wired. Only above
sensors are placed in SoC.
- Praveenkumar
+ interrupts = <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "combined";
+ #qcom,sensors = <5>;
+ #thermal-sensor-cells = <1>;
+ };
+
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq5332-tlmm";
reg = <0x01000000 0x300000>;
