The VSC8531 and similar PHYs (i.e. VSC8530, VSC8531, VSC8540 & VSC8541)
have a CLKOUT pin on the chip that can be controlled by register (13G in
the General Purpose Registers page) that can be configured to output a
frequency of 25, 50 or 125 Mhz.
This is useful when wanting to provide a clock source for the MAC in some
board designs.
Signed-off-by: Marius Muresan <marius.muresan@xxxxxx>
Signed-off-by: Alexandru Ardelean <alex@xxxxxxxxxxx>
---
The original patch was done by Marius.
The final (upstream) version was done by Alex.
Tested on VSC8531.
drivers/net/phy/mscc/mscc.h | 5 ++++
drivers/net/phy/mscc/mscc_main.c | 40 ++++++++++++++++++++++++++++++++
2 files changed, 45 insertions(+)
diff --git a/drivers/net/phy/mscc/mscc.h b/drivers/net/phy/mscc/mscc.h
index 7a962050a4d4..4ea21921a7ba 100644
--- a/drivers/net/phy/mscc/mscc.h
+++ b/drivers/net/phy/mscc/mscc.h
@@ -181,6 +181,11 @@ enum rgmii_clock_delay {
#define VSC8502_RGMII_TX_DELAY_MASK 0x0007
#define VSC8502_RGMII_RX_CLK_DISABLE 0x0800
+/* CKLOUT Control register, for VSC8531 and similar */
+#define VSC8531_CLKOUT_CNTL 13
+#define VSC8531_CLKOUT_CNTL_ENABLE BIT(15)
+#define VSC8531_CLKOUT_CNTL_FREQ_MASK GENMASK(14, 13)
+
#define MSCC_PHY_WOL_LOWER_MAC_ADDR 21
#define MSCC_PHY_WOL_MID_MAC_ADDR 22
#define MSCC_PHY_WOL_UPPER_MAC_ADDR 23
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 4171f01d34e5..61c1554935ce 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -618,6 +618,41 @@ static void vsc85xx_tr_write(struct phy_device *phydev, u16 addr, u32 val)
__phy_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
}
+static int vsc8531_clkout_config(struct phy_device *phydev)
+{
+ static const u32 freq_vals[] = { 25, 50, 125 };
+ struct device *dev = &phydev->mdio.dev;
+ u16 mask, set;
+ u32 freq, i;
+ int rc;
+
+ mask = VSC8531_CLKOUT_CNTL_ENABLE | VSC8531_CLKOUT_CNTL_FREQ_MASK;
+ set = 0;
+
+ if (device_property_read_u32(dev, "vsc8531,clkout-freq-mhz", &freq) == 0) {
+ /* The indices from 'freq_vals' are used in the register */
+ for (i = 0; i < ARRAY_SIZE(freq_vals); i++) {
+ if (freq != freq_vals[i])
+ continue;
+
+ set |= VSC8531_CLKOUT_CNTL_ENABLE |
+ FIELD_PREP(VSC8531_CLKOUT_CNTL_FREQ_MASK, i);
+ break;
+ }
+ if (set == 0)
+ dev_warn(dev,
+ "Invalid 'vsc8531,clkout-freq-mhz' value %u\n",
+ freq);
+ }
+
+ mutex_lock(&phydev->lock);
+ rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_GPIO,
+ VSC8531_CLKOUT_CNTL, mask, set);
+ mutex_unlock(&phydev->lock);
+
+ return rc;
+}
+
static int vsc8531_pre_init_seq_set(struct phy_device *phydev)
{
int rc;
@@ -1852,6 +1887,11 @@ static int vsc85xx_config_init(struct phy_device *phydev)
rc = vsc8531_pre_init_seq_set(phydev);
if (rc)
return rc;
+
+ rc = vsc8531_clkout_config(phydev);
+ if (rc)
+ return rc;
+
}
rc = vsc85xx_eee_init_seq_set(phydev);
--
2.40.1
