Hello Krzysztof!
On Thu, 2023-06-01 at 10:30 +0200, Krzysztof Kozlowski wrote:
> On 01/06/2023 07:45, Nikita Shubin wrote:
> > This adds a divice for Cirrus ep93xx SoC amd ts7250 board that has
> > been
>
> device
>
> > my testing target for ep93xx device support.
> >
> > Also inluded device tree for Liebherr BK3.1 board through it's not
> > a
>
> included
>
> > complete support.
>
> Thank you for your patch. There is something to discuss/improve.
>
>
> >
> > Signed-off-by: Nikita Shubin <nikita.shubin@xxxxxxxxxxx>
> > ---
> >
> > Notes:
> > v0 -> v1:
> >
> > - add empty chosen node
> > - s/dallas,rtc-m48t86/st,m48t86/
> > - changed phy_id to phy-handle
> > - dropped gpio chip-label's
> > - s/eth@80010000/ethernet@80010000
> > - s/use_dma/ep9301,use-dma
> > - added i2s to bk3
> >
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/ep93xx-bk3.dts | 119 +++++++
> > arch/arm/boot/dts/ep93xx-ts7250.dts | 132 ++++++++
> > arch/arm/boot/dts/ep93xx.dtsi | 466
> > ++++++++++++++++++++++++++++
>
> Split adding DTSI from adding boards.
>
> > 4 files changed, 718 insertions(+)
> > create mode 100644 arch/arm/boot/dts/ep93xx-bk3.dts
> > create mode 100644 arch/arm/boot/dts/ep93xx-ts7250.dts
> > create mode 100644 arch/arm/boot/dts/ep93xx.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile
> > b/arch/arm/boot/dts/Makefile
> > index 59829fc90315..a68f868fffe7 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1670,3 +1670,4 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> > aspeed-bmc-vegman-n110.dtb \
> > aspeed-bmc-vegman-rx20.dtb \
> > aspeed-bmc-vegman-sx20.dtb
> > +dtb-$(CONFIG_ARCH_EP93XX) += ep93xx-ts7250.dtb
> > diff --git a/arch/arm/boot/dts/ep93xx-bk3.dts
> > b/arch/arm/boot/dts/ep93xx-bk3.dts
> > new file mode 100644
> > index 000000000000..215587c498e6
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/ep93xx-bk3.dts
> > @@ -0,0 +1,119 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Device Tree file for Liebherr controller BK3.1 based on Cirrus
> > EP9302 SoC
> > + */
> > +/dts-v1/;
> > +#include "ep93xx.dtsi"
> > +
> > +/ {
> > + model = "Liebherr controller BK3.1";
> > + compatible = "liebherr,bk3", "cirrus,ep9301";
> > +
> > + chosen {
> > + };
> > +
> > + memory {
> > + device_type = "memory";
> > + };
> > +
> > + soc {
> > + nand-controller@60000000 {
>
> Override/extend by label/phandle.
>
> > + compatible = "technologic,ts7200-nand";
> > + reg = <0x60000000 0x8000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition@0 {
> > + label = "System";
> > + reg = <0x00000000
> > 0x01e00000>;
> > + read-only;
> > + };
> > +
> > + partition@1e00000 {
> > + label = "Data";
> > + reg = <0x01e00000
> > 0x05f20000>;
> > + };
> > +
> > + partition@7d20000 {
> > + label = "RedBoot";
> > + reg = <0x07d20000
> > 0x002e0000>;
> > + read-only;
> > + };
> > + };
> > + };
> > +
> > + syscon: syscon@80930000 {
>
> Override/extend by label/phandle.
>
> > + pinctrl: pinctrl {
> > + compatible = "cirrus,ep9301-
> > pinctrl";
>
> Why this is board specific?
You are right - it's SoC specific, but currently we only have boards
with ep9302 with according device trees:
- ts7250
- bk3
- edb9302
We were hoping someone with other SoC's will join - like Hartley
Sweeten with Vision Engraving Systems EP9307 SoM, but no one showed up.
I've changed added compatible "cirrus,ep9301-pinctrl" in ep93xx.dtsi as
default and removed from all other board .dts.
>
> > + };
> > + };
> > +
> > + gpio1: gpio@80840004 {
>
> Override/extend by label/phandle.
>
> > + /* PWM */
> > + gpio-ranges = <&pinctrl 6 163 1>;
> > + };
> > + };
> > +};
> > +
> > +&gpio1 {
> > + /* PWM */
> > + gpio-ranges = <&pinctrl 6 163 1>;
> > +};
> > +
> > +&gpio4 {
> > + gpio-ranges = <&pinctrl 0 97 2>;
> > + status = "okay";
> > +};
> > +
> > +&gpio6 {
> > + gpio-ranges = <&pinctrl 0 87 2>;
> > + status = "okay";
> > +};
> > +
> > +&gpio7 {
> > + gpio-ranges = <&pinctrl 2 199 4>;
> > + status = "okay";
> > +};
> > +
> > +&i2c {
> > + status = "okay";
> > +};
> > +
> > +&spi0: spi@808a0000 {
> > + cs-gpios = <&gpio5 3 0>;
>
> Use proper defines for flags.
>
> > + status = "okay";
>
> What's here? Empty enabled bus?
>
>
> > +};
> > +
> > +ð0 {
> > + phy-handle = <&phy0>;
> > +};
> > +
> > +&mdio0 {
> > + phy0: ethernet-phy@1 {
> > + reg = <1>;
> > + device_type = "ethernet-phy";
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&usb {
> > + status = "okay";
> > +};
> > +
> > +&i2s {
>
> Up to you, but I seriously recommend keeping all labels ordered by
> name.
> Avoids conflicts.
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2s_on_ac97_pins>;
> > + /delete-property/ status;
>
> ??? I don't understand. Why would you do this?
>
> ...
>
> > diff --git a/arch/arm/boot/dts/ep93xx.dtsi
> > b/arch/arm/boot/dts/ep93xx.dtsi
> > new file mode 100644
> > index 000000000000..6da556ceaf04
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/ep93xx.dtsi
> > @@ -0,0 +1,466 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Device Tree file for Cirrus Logic systems EP93XX SoC
> > + */
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/clock/cirrus,ep93xx-clock.h>
> > +/ {
> > + soc {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > + compatible = "simple-bus";
> > +
> > + syscon: syscon@80930000 {
> > + compatible = "cirrus,ep9301-syscon",
> > + "syscon", "simple-
> > mfd";
>
> Broken wrapping. Align these with previous ".
>
> > + reg = <0x80930000 0x1000>;
> > +
> > + ep9301-reboot {
>
> Just "reboot" (and fix bindings)... but why would you need it in the
> first place? I think something is seriously missing in your bindings.
>
> > + compatible = "cirrus,ep9301-
> > reboot";
> > + };
> > +
> > + eclk: clock-controller {
> > + #clock-cells = <1>;
> > + compatible = "cirrus,ep9301-clk";
> > + status = "okay";
> > + clocks = <&xtali>;
> > + };
> > +
> > + pinctrl: pinctrl {
>
> Missing compatible.
>
> > + spi_default_pins: pins-spi {
> > + function = "spi";
> > + groups = "ssp";
> > + };
> > +
> > + ac97_default_pins: pins-ac97 {
> > + function = "ac97";
> > + groups = "ac97";
> > + };
> > +
> > + i2s_on_ssp_pins: pins-i2sonssp {
> > + function = "i2s";
> > + groups = "i2s_on_ssp";
> > + };
> > +
> > + i2s_on_ac97_pins: pins-i2sonac97 {
> > + function = "i2s";
> > + groups = "i2s_on_ac97";
> > + };
> > +
> > + gpio1_default_pins: pins-gpio1 {
> > + function = "gpio";
> > + groups = "gpio1agrp";
> > + };
> > +
> > + pwm1_default_pins: pins-pwm1 {
> > + function = "pwm";
> > + groups = "pwm1";
> > + };
> > +
> > + gpio2_default_pins: pins-gpio2 {
> > + function = "gpio";
> > + groups = "gpio2agrp";
> > + };
> > +
> > + gpio3_default_pins: pins-gpio3 {
> > + function = "gpio";
> > + groups = "gpio3agrp";
> > + };
> > +
> > + keypad_default_pins: pins-keypad {
> > + function = "keypad";
> > + groups = "keypadgrp";
> > + };
> > +
> > + gpio4_default_pins: pins-gpio4 {
> > + function = "gpio";
> > + groups = "gpio4agrp";
> > + };
> > +
> > + gpio6_default_pins: pins-gpio6 {
> > + function = "gpio";
> > + groups = "gpio6agrp";
> > + };
> > +
> > + gpio7_default_pins: pins-gpio7 {
> > + function = "gpio";
> > + groups = "gpio7agrp";
> > + };
> > +
> > + ide_default_pins: pins-ide {
> > + function = "pata";
> > + groups = "idegrp";
> > + };
> > +
> > + lcd_on_dram0_pins: pins-
> > rasteronsdram0 {
> > + function = "lcd";
> > + groups =
> > "rasteronsdram0grp";
> > + };
> > +
> > + lcd_on_dram3_pins: pins-
> > rasteronsdram3 {
> > + function = "lcd";
> > + groups =
> > "rasteronsdram3grp";
>
> I would expect somewhere two groups since you explicitly allow it.
>
> > + };
> > + };
> > + };
> > +
> > + vic0: interrupt-controller@800b0000 {
> > + compatible = "arm,pl192-vic";
> > + interrupt-controller;
> > + reg = <0x800b0000 0x1000>;
>
> compatible first, reg is second. ranges if present - third. Fix it
> everywhere.
>
> > + #interrupt-cells = <1>;
> > + valid-mask = <0x7ffffffc>;
> > + valid-wakeup-mask = <0x0>;
> > + };
> > +
> > + vic1: interrupt-controller@800c0000 {
> > + compatible = "arm,pl192-vic";
> > + interrupt-controller;
> > + reg = <0x800c0000 0x1000>;
> > + #interrupt-cells = <1>;
> > + valid-mask = <0x1fffffff>;
> > + valid-wakeup-mask = <0x0>;
> > + };
> > +
> > + timer: timer@80810000 {
> > + compatible = "cirrus,ep9301-timer";
> > + reg = <0x80810000 0x100>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <19>;
> > + };
> > +
> > + dma0: dma-controller@80000000 {
> > + compatible = "cirrus,ep9301-dma-m2p";
> > + reg = <0x80000000 0x0040>,
> > + <0x80000040 0x0040>,
> > + <0x80000080 0x0040>,
> > + <0x800000c0 0x0040>,
> > + <0x80000240 0x0040>,
> > + <0x80000200 0x0040>,
> > + <0x800002c0 0x0040>,
> > + <0x80000280 0x0040>,
> > + <0x80000340 0x0040>,
> > + <0x80000300 0x0040>;
> > + clocks = <&eclk EP93XX_CLK_M2P0>,
> > + <&eclk EP93XX_CLK_M2P1>,
> > + <&eclk EP93XX_CLK_M2P2>,
> > + <&eclk EP93XX_CLK_M2P3>,
> > + <&eclk EP93XX_CLK_M2P4>,
> > + <&eclk EP93XX_CLK_M2P5>,
> > + <&eclk EP93XX_CLK_M2P6>,
> > + <&eclk EP93XX_CLK_M2P7>,
> > + <&eclk EP93XX_CLK_M2P8>,
> > + <&eclk EP93XX_CLK_M2P9>;
> > + clock-names = "m2p0", "m2p1",
> > + "m2p2", "m2p3",
> > + "m2p4", "m2p5",
> > + "m2p6", "m2p7",
> > + "m2p8", "m2p9";
> > + interrupt-parent = <&vic0>;
> > + interrupts = <7>, <8>, <9>, <10>, <11>,
> > + <12>, <13>, <14>, <15>, <16>;
> > + #dma-cells = <1>;
> > + };
> > +
> > + dma1: dma-controller@80000100 {
> > + compatible = "cirrus,ep9301-dma-m2m";
> > + reg = <0x80000100 0x0040>,
> > + <0x80000140 0x0040>;
> > + clocks = <&eclk EP93XX_CLK_M2M0>,
> > + <&eclk EP93XX_CLK_M2M1>;
> > + clock-names = "m2m0", "m2m1";
> > + interrupt-parent = <&vic0>;
> > + interrupts = <17>, <18>;
> > + #dma-cells = <1>;
> > + };
> > +
> > + i2s: i2s@80820000 {
> > + compatible = "cirrus,ep9301-i2s";
> > + #sound-dai-cells = <0>;
> > + reg = <0x80820000 0x100>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <28>;
> > + clocks = <&eclk EP93XX_CLK_I2S_MCLK
> > + &eclk EP93XX_CLK_I2S_SCLK
> > + &eclk EP93XX_CLK_I2S_LRCLK>;
> > + clock-names = "mclk", "sclk", "lrclk";
> > + status = "disabled";
> > + };
> > +
> > + gpio0: gpio@80840000 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840000 0x04>,
> > + <0x80840010 0x04>,
> > + <0x80840090 0x1c>;
>
> Messed wrapping.
>
> > + reg-names = "data", "dir", "intr";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <27>;
> > + };
> > +
> > + gpio1: gpio@80840004 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840004 0x04>,
> > + <0x80840014 0x04>,
> > + <0x808400ac 0x1c>;
>
> Ditto, in other places as well.
>
> > + reg-names = "data", "dir", "intr";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <27>;
> > + };
> > +
> > + gpio2: gpio@80840008 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840008 0x04>,
> > + <0x80840018 0x04>;
> > + reg-names = "data", "dir";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + status = "disabled";
>
> Status is usually last.
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio2_default_pins>;
> > + };
> > +
> > + gpio3: gpio@8084000c {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x8084000c 0x04>,
> > + <0x8084001c 0x04>;
> > + reg-names = "data", "dir";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio3_default_pins>;
> > + };
> > +
> > + gpio4: gpio@80840020 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840020 0x04>,
> > + <0x80840024 0x04>;
> > + reg-names = "data", "dir";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio4_default_pins>;
> > + };
> > +
> > + gpio5: gpio@80840030 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840030 0x04>,
> > + <0x80840034 0x04>,
> > + <0x8084004c 0x1c>;
> > + reg-names = "data", "dir", "intr";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + interrupts-extended = <&vic0 19>, <&vic0
> > 20>,
> > + <&vic0 21>, <&vic0 22>,
> > + <&vic1 15>, <&vic1 16>,
> > + <&vic1 17>, <&vic1 18>;
> > + };
> > +
> > + gpio6: gpio@80840038 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840038 0x04>,
> > + <0x8084003c 0x04>;
> > + reg-names = "data", "dir";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio6_default_pins>;
> > + };
> > +
> > + gpio7: gpio@80840040 {
> > + compatible = "cirrus,ep9301-gpio";
> > + reg = <0x80840040 0x04>,
> > + <0x80840044 0x04>;
> > + reg-names = "data", "dir";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio7_default_pins>;
> > + };
> > +
> > + ide: ide@800a0000 {
> > + compatible = "cirrus,ep9312-pata";
> > + reg = <0x800a0000 0x38>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <8>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ide_default_pins>;
> > + };
> > +
> > + uart0: uart@808c0000 {
>
> This should scream with dtbs_check. serial.
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check` (see
> Documentation/devicetree/bindings/writing-schema.rst for
> instructions).
make dtbs_check is totally clean now:
```
make -j34 -C build-linux ARCH=arm CROSS_COMPILE=armv4t-softfloat-linux-
gnueabi- dtbs_check
make[1]: Entering directory '/home/maquefel/workshop/ts7250-boot-
build/build-linux'
UPD include/config/kernel.release
DTC_CHK arch/arm/boot/dts/cirrus/ep93xx-edb9302.dtb
arch/arm/boot/dts/cirrus/ep93xx-edb9302.dtb:0:0: /soc/ac97@80880000:
failed to match any schema with compatible: ['cirrus,ep9301-ac97']
arch/arm/boot/dts/cirrus/ep93xx-edb9302.dtb:0:0:
/soc/spi@808a0000/codec@0: failed to match any schema with compatible:
['cirrus,cs4271']
/home/maquefel/workshop/ts7250-boot-build/build-
linux/arch/arm/boot/dts/cirrus/ep93xx-edb9302.dtb: sound: 'simple-
audio-card,convert-sample-format' does not match any of the regexes:
'^simple-audio-card,codec(@[0-9a-f]+)?$', '^simple-audio-card,cpu(@[0-
9a-f]+)?$', '^simple-audio-card,dai-link(@[0-9a-f]+)?$', '^simple-
audio-card,plat(@[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/maquefel/workshop/ts7250-boot-
build/linux/Documentation/devicetree/bindings/sound/simple-card.yaml
make[1]: Leaving directory '/home/maquefel/workshop/ts7250-boot-
build/build-linux'
```
>
> > + compatible = "arm,primecell";
> > + reg = <0x808c0000 0x1000>;
> > + arm,primecell-periphid = <0x00041010>;
> > + clocks = <&eclk EP93XX_CLK_UART1>, <&eclk
> > EP93XX_CLK_UART>;
> > + clock-names = "apb:uart1", "apb_pclk";
> > + interrupt-parent = <&vic1>;
> > + interrupts = <20>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: uart@808d0000 {
> > + compatible = "arm,primecell";
> > + reg = <0x808d0000 0x1000>;
> > + arm,primecell-periphid = <0x00041010>;
> > + clocks = <&eclk EP93XX_CLK_UART2>, <&eclk
> > EP93XX_CLK_UART>;
> > + clock-names = "apb:uart2", "apb_pclk";
> > + interrupt-parent = <&vic1>;
> > + interrupts = <22>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: uart@808b0000 {
> > + compatible = "arm,primecell";
> > + reg = <0x808b0000 0x1000>;
> > + arm,primecell-periphid = <0x00041010>;
> > + clocks = <&eclk EP93XX_CLK_UART3>, <&eclk
> > EP93XX_CLK_UART>;
> > + clock-names = "apb:uart3", "apb_pclk";
> > + interrupt-parent = <&vic1>;
> > + interrupts = <23>;
> > + status = "disabled";
> > + };
> > +
> > + usb0: usb@80020000 {
> > + compatible = "generic-ohci";
> > + reg = <0x80020000 0x10000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <24>;
> > + clocks = <&eclk EP93XX_CLK_USB>;
> > + status = "disabled";
> > + };
> > +
> > + eth0: ethernet@80010000 {
> > + compatible = "cirrus,ep9301-eth";
> > + reg = <0x80010000 0x10000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <7>;
> > + mdio0: mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
>
> Your SoC comes with mdio? If so, why is this empty?
It has a builtin MDIO and only reason for this is to provide phy-id via
device tree in a correct way:
```
ð0 {
phy-handle = <&phy0>;
};
&mdio0 {
phy0: ethernet-phy@1 {
reg = <1>;
device_type = "ethernet-phy";
};
};
```
There is no other purpose for this node.
Thank you Krzysztof!
All other issues fixed.
>
> > + };
> > + };
> > +
> > + rtc0: rtc@80920000 {
> > + compatible = "cirrus,ep9301-rtc";
> > + reg = <0x80920000 0x100>;
> > + };
> > +
> > + spi0: spi@808a0000 {
> > + compatible = "cirrus,ep9301-spi";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x808a0000 0x18>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <21>;
> > + clocks = <&eclk EP93XX_CLK_SPI>;
> > + cs-gpios = <&gpio5 2 0>;
>
> defines... but why is it here in the first place? Rarely CS gpios are
> part of the SoC. I have several of such questions further as well, so
> this looks like you are mixing SoC and boards in one file.
>
> > + cirrus,ep9301-use-dma;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi_default_pins>;
> > + status = "disabled";
> > + };
> > +
> > + adc: adc@80900000 {
> > + compatible = "cirrus,ep9301-adc";
> > + reg = <0x80900000 0x28>;
> > + clocks = <&eclk EP93XX_CLK_ADC>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <30>;
> > + status = "disabled";
> > + };
> > +
> > + watchdog0: watchdog@80940000 {
> > + compatible = "cirrus,ep9301-wdt";
> > + reg = <0x80940000 0x08>;
> > + };
> > +
> > + pwm0: pwm@80910000 {
> > + compatible = "cirrus,ep9301-pwm";
> > + reg = <0x80910000 0x10>;
> > + clocks = <&eclk EP93XX_CLK_PWM>;
> > + status = "disabled";
> > + };
> > +
> > + pwm1: pwm@80910020 {
> > + compatible = "cirrus,ep9301-pwm";
> > + reg = <0x80910020 0x10>;
> > + clocks = <&eclk EP93XX_CLK_PWM>;
> > + status = "disabled";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm1_default_pins>;
> > + };
> > +
> > + keypad: keypad@800f0000 {
> > + compatible = "cirrus,ep9307-keypad";
> > + reg = <0x800f0000 0x0c>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <29>;
> > + clocks = <&eclk EP93XX_CLK_KEYPAD>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&keypad_default_pins>;
> > + linux,keymap =
> > + <KEY_UP>,
> > + <KEY_DOWN>,
> > + <KEY_VOLUMEDOWN>,
> > + <KEY_HOME>,
> > + <KEY_RIGHT>,
> > + <KEY_LEFT>,
> > + <KEY_ENTER>,
> > + <KEY_VOLUMEUP>,
> > + <KEY_F6>,
> > + <KEY_F8>,
> > + <KEY_F9>,
> > + <KEY_F10>,
> > + <KEY_F1>,
> > + <KEY_F2>,
> > + <KEY_F3>,
> > + <KEY_POWER>;
> > + };
> > + };
> > +
> > + xtali: oscillator {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <14745600>;
> > + clock-output-names = "xtali";
> > + };
> > +
> > + i2c0: i2c0 {
>
> i2c or i2c-0
>
> > + compatible = "i2c-gpio";
> > + sda-gpios = <&gpio6 1
> > (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> > + scl-gpios = <&gpio6 0
> > (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "disabled";
>
> Wait, what? Why this is disabled? If this is part of the SoC,
> although
> hardly looks like, then it should be complete. What is missing? How
> one
> could design SoC with incomplete GPIO I2C controller?
>
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
>
> I really doubt this is property of the SoC. Please double check as it
> really looks wrong.
>
>
> > + led0 {
>
> led-0
>
> > + label = "grled";
> > + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + function = LED_FUNCTION_HEARTBEAT;
> > + };
> > +
> > + led1 {
> led-1
>
> > + label = "rdled";
> > + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
> > + function = LED_FUNCTION_FAULT;
> > + };
> > + };
> > +};
>
> Best regards,
> Krzysztof
>
