[PATCH v2 23/27] ARM: dts: qcom: apq8064: move RPM regulators to board files

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The set of regulators available over the RPM requests is not a property
of the SoC. Move them to board files.

Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
 .../dts/qcom/qcom-apq8064-asus-nexus7-flo.dts |  49 ++++----
 .../boot/dts/qcom/qcom-apq8064-cm-qs600.dts   |  26 ++---
 .../boot/dts/qcom/qcom-apq8064-ifc6410.dts    |  33 +++---
 .../qcom-apq8064-sony-xperia-lagan-yuga.dts   | 105 ++++++++++--------
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi      |  63 -----------
 5 files changed, 115 insertions(+), 161 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
index d5dee70620c2..1caa73e20bc9 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -192,22 +192,20 @@ &mdp_dsi1_out {
 &rpm {
 	regulators {
 		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-		vin_lvs1_3_6-supply = <&pm8921_s4>;
-		vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-
 		vdd_l24-supply = <&pm8921_s1>;
 		vdd_l25-supply = <&pm8921_s1>;
-		vin_lvs2-supply = <&pm8921_s1>;
-
 		vdd_l26-supply = <&pm8921_s7>;
 		vdd_l27-supply = <&pm8921_s7>;
 		vdd_l28-supply = <&pm8921_s7>;
 
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
 		vdd_ncp-supply = <&pm8921_l6>;
 
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -216,7 +214,7 @@ s1 {
 		};
 
 		/* msm otg HSUSB_VDDCX */
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1150000>;
 			qcom,switch-mode-frequency = <4800000>;
@@ -229,55 +227,58 @@ s3 {
 		 * tabla2x-slim-CDC_VDD_CP
 		 * tabla2x-slim-VDDIO_CDC
 		 */
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 			regulator-always-on;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
 		/* mipi_dsi.1-dsi1_pll_vdda */
-		l2 {
+		pm8921_l2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			regulator-always-on;
 		};
 
 		/* msm_otg-HSUSB_3p3 */
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
 			bias-pull-down;
 		};
 
 		/* msm_otg-HSUSB_1p8 */
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
 		/* msm_sdcc.1-sdc_vdd */
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			regulator-always-on;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 		};
 
+		pm8921_l8: l8 {
+		};
+
 		/* mipi_dsi.1-dsi1_avdd */
-		l11 {
+		pm8921_l11: l11 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
@@ -285,14 +286,14 @@ l11 {
 		};
 
 		/* pwm_power for backlight */
-		l17 {
+		pm8921_l17: l17 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			regulator-always-on;
 		};
 
 		/* camera, qdsp6 */
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
@@ -302,32 +303,32 @@ l23 {
 		 * tabla2x-slim-CDC_VDDA_A_1P2V
 		 * tabla2x-slim-VDDD_CDC_D
 		 */
-		l25 {
+		pm8921_l25: l25 {
 			regulator-min-microvolt = <1250000>;
 			regulator-max-microvolt = <1250000>;
 			bias-pull-down;
 		};
 
-		lvs1 {
+		pm8921_lvs1: lvs1 {
 			bias-pull-down;
 		};
 
-		lvs4 {
+		pm8921_lvs4: lvs4 {
 			bias-pull-down;
 		};
 
-		lvs5 {
+		pm8921_lvs5: lvs5 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 		/*
 		 * mipi_dsi.1-dsi1_vddio
 		 * pil_riva-pll_vdd
 		 */
-		lvs7 {
+		pm8921_lvs7: lvs7 {
 			bias-pull-down;
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
index ffd654ab0b57..6472277d1c6d 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -85,10 +85,6 @@ pinconf {
 
 &rpm {
 	regulators {
-		vin_lvs1_3_6-supply = <&pm8921_s4>;
-		vin_lvs2-supply = <&pm8921_s1>;
-		vin_lvs4_5_7-supply = <&pm8921_s4>;
-
 		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
 		vdd_l24-supply = <&pm8921_s1>;
 		vdd_l25-supply = <&pm8921_s1>;
@@ -96,9 +92,12 @@ regulators {
 		vdd_l27-supply = <&pm8921_s7>;
 		vdd_l28-supply = <&pm8921_s7>;
 
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
 
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -106,52 +105,51 @@ s1 {
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1400000>;
 			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2750000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1700000>;
 			regulator-max-microvolt = <1900000>;
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
-
 	};
 };
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
index 12bf8ea3fb93..39c44fae9d14 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -196,10 +196,6 @@ pinconf {
 
 &rpm {
 	regulators {
-		vin_lvs1_3_6-supply = <&pm8921_s4>;
-		vin_lvs2-supply = <&pm8921_s1>;
-		vin_lvs4_5_7-supply = <&pm8921_s4>;
-
 		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
 		vdd_l24-supply = <&pm8921_s1>;
 		vdd_l25-supply = <&pm8921_s1>;
@@ -207,9 +203,12 @@ regulators {
 		vdd_l27-supply = <&pm8921_s7>;
 		vdd_l28-supply = <&pm8921_s7>;
 
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
 
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -217,59 +216,63 @@ s1 {
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1400000>;
 			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2750000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1700000>;
 			regulator-max-microvolt = <1900000>;
 			bias-pull-down;
 		};
 
-		lvs1 {
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_hdmi_switch: hdmi-switch {
 			bias-pull-down;
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
index 53dd9d79556f..6988bd212924 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -85,23 +85,36 @@ gpio_keys_pin_a: gpio-keys-active-state {
 &riva {
 	pinctrl-names = "default";
 	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+
+	vddcx-supply = <&pm8921_s3>;
+	vddmx-supply = <&pm8921_l24>;
+	vddpx-supply = <&pm8921_s4>;
+
 	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8921_l4>;
+		vddrfa-supply = <&pm8921_s2>;
+		vddpa-supply = <&pm8921_l10>;
+		vdddig-supply = <&pm8921_lvs2>;
+	};
 };
 
 &rpm {
 	regulators {
 		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
-		vin_lvs_1_3_6-supply = <&pm8921_s4>;
-		vin_lvs_4_5_7-supply = <&pm8921_s4>;
-		vin_ncp-supply = <&pm8921_l6>;
-		vin_lvs2-supply = <&pm8921_s4>;
 		vin_l24-supply = <&pm8921_s1>;
 		vin_l25-supply = <&pm8921_s1>;
 		vin_l27-supply = <&pm8921_s7>;
 		vin_l28-supply = <&pm8921_s7>;
 
+		vin_lvs_1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs_4_5_7-supply = <&pm8921_s4>;
+		vin_ncp-supply = <&pm8921_l6>;
+
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -109,21 +122,21 @@ s1 {
 			bias-pull-down;
 		};
 
-		s2 {
+		pm8921_s2: s2 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1150000>;
 			qcom,switch-mode-frequency = <4800000>;
 			bias-pull-down;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-always-on;
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
@@ -132,205 +145,207 @@ s4 {
 			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s8 {
+		pm8921_s8: s8 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
 			qcom,switch-mode-frequency = <1600000>;
 		};
 
 		/* PMOS LDO */
-		l1 {
+		pm8921_l1: l1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
 			bias-pull-down;
 		};
 
-		l2 {
+		pm8921_l2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-always-on;
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l7 {
+		pm8921_l7: l7 {
 			regulator-min-microvolt = <1850000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l8 {
+		pm8921_l8: l8 {
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
 			bias-pull-down;
 		};
 
-		l9 {
+		pm8921_l9: l9 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l10 {
+		pm8921_l10: l10 {
 			regulator-min-microvolt = <2900000>;
 			regulator-max-microvolt = <2900000>;
 			bias-pull-down;
 		};
 
-		l11 {
+		pm8921_l11: l11 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l12 {
+		pm8921_l12: l12 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l14 {
+		pm8921_l14: l14 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l15 {
+		pm8921_l15: l15 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l16 {
+		pm8921_l16: l16 {
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
 			bias-pull-down;
 		};
 
-		l17 {
+		pm8921_l17: l17 {
 			regulator-min-microvolt = <2000000>;
 			regulator-max-microvolt = <2000000>;
 			bias-pull-down;
 		};
 
-		l18 {
+		pm8921_l18: l18 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l21 {
+		pm8921_l21: l21 {
 			regulator-min-microvolt = <1050000>;
 			regulator-max-microvolt = <1050000>;
 			bias-pull-down;
 		};
 
-		l22 {
+		pm8921_l22: l22 {
 			regulator-min-microvolt = <2600000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l24 {
+		pm8921_l24: l24 {
 			regulator-min-microvolt = <750000>;
 			regulator-max-microvolt = <1150000>;
 			bias-pull-down;
 		};
 
-		l25 {
+		pm8921_l25: l25 {
 			regulator-always-on;
 			regulator-min-microvolt = <1250000>;
 			regulator-max-microvolt = <1250000>;
 			bias-pull-down;
 		};
 
-		l27 {
+		pm8921_l27: l27 {
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
 		};
 
-		l28 {
+		pm8921_l28: l28 {
 			regulator-min-microvolt = <1050000>;
 			regulator-max-microvolt = <1050000>;
 			bias-pull-down;
 		};
 
-		l29 {
+		pm8921_l29: l29 {
 			regulator-min-microvolt = <2000000>;
 			regulator-max-microvolt = <2000000>;
 			bias-pull-down;
 		};
 
 		/* Low Voltage Switch */
-		lvs1 {
+		pm8921_lvs1: lvs1 {
 			bias-pull-down;
 		};
 
-		lvs2 {
+		pm8921_lvs2: lvs2 {
 			bias-pull-down;
 		};
 
-		lvs3 {
+		pm8921_lvs3: lvs3 {
 			bias-pull-down;
 		};
 
-		lvs4 {
+		pm8921_lvs4: lvs4 {
 			bias-pull-down;
 		};
 
-		lvs5 {
+		pm8921_lvs5: lvs5 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 
-		lvs7 {
+		pm8921_lvs7: lvs7 {
 			bias-pull-down;
 		};
 
-		usb-switch {};
+		pm8921_usb_switch: usb-switch {};
 
-		hdmi-switch {};
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
 
-		ncp {
+		pm8921_ncp: ncp {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <1600000>;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 2a5a3b2fb8e9..36c68ee5be65 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -795,60 +795,6 @@ rpmcc: clock-controller {
 				clocks = <&pxo_board>, <&cxo_board>;
 				clock-names = "pxo", "cxo";
 			};
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-
-				pm8921_s1: s1 {};
-				pm8921_s2: s2 {};
-				pm8921_s3: s3 {};
-				pm8921_s4: s4 {};
-				pm8921_s7: s7 {};
-				pm8921_s8: s8 {};
-
-				pm8921_l1: l1 {};
-				pm8921_l2: l2 {};
-				pm8921_l3: l3 {};
-				pm8921_l4: l4 {};
-				pm8921_l5: l5 {};
-				pm8921_l6: l6 {};
-				pm8921_l7: l7 {};
-				pm8921_l8: l8 {};
-				pm8921_l9: l9 {};
-				pm8921_l10: l10 {};
-				pm8921_l11: l11 {};
-				pm8921_l12: l12 {};
-				pm8921_l14: l14 {};
-				pm8921_l15: l15 {};
-				pm8921_l16: l16 {};
-				pm8921_l17: l17 {};
-				pm8921_l18: l18 {};
-				pm8921_l21: l21 {};
-				pm8921_l22: l22 {};
-				pm8921_l23: l23 {};
-				pm8921_l24: l24 {};
-				pm8921_l25: l25 {};
-				pm8921_l26: l26 {};
-				pm8921_l27: l27 {};
-				pm8921_l28: l28 {};
-				pm8921_l29: l29 {};
-
-				pm8921_lvs1: lvs1 {};
-				pm8921_lvs2: lvs2 {};
-				pm8921_lvs3: lvs3 {};
-				pm8921_lvs4: lvs4 {};
-				pm8921_lvs5: lvs5 {};
-				pm8921_lvs6: lvs6 {};
-				pm8921_lvs7: lvs7 {};
-
-				pm8921_usb_switch: usb-switch {};
-
-				pm8921_hdmi_switch: hdmi-switch {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {};
-			};
 		};
 
 		usb1: usb@12500000 {
@@ -1528,10 +1474,6 @@ riva: riva-pil@3200800 {
 
 			memory-region = <&wcnss_mem>;
 
-			vddcx-supply = <&pm8921_s3>;
-			vddmx-supply = <&pm8921_l24>;
-			vddpx-supply = <&pm8921_s4>;
-
 			status = "disabled";
 
 			iris {
@@ -1539,11 +1481,6 @@ iris {
 
 				clocks = <&cxo_board>;
 				clock-names = "xo";
-
-				vddxo-supply = <&pm8921_l4>;
-				vddrfa-supply = <&pm8921_s2>;
-				vddpa-supply = <&pm8921_l10>;
-				vdddig-supply = <&pm8921_lvs2>;
 			};
 
 			smd-edge {
-- 
2.39.2




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux