Re: [PATCH] dt-bindings: serial: tegra-hsuart: Convert to json-schema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jun 30, 2023 at 03:58:43PM +0200, Thierry Reding wrote:
> From: Thierry Reding <treding@xxxxxxxxxx>
> 
> Convert the Tegra High-Speed UART bindings from the free-form text
> format to json-schema.
> 
> Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
> ---
>  .../bindings/serial/nvidia,tegra20-hsuart.txt |  73 -----------
>  .../serial/nvidia,tegra20-hsuart.yaml         | 124 ++++++++++++++++++
>  2 files changed, 124 insertions(+), 73 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt
>  create mode 100644 Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml
> 
> diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt
> deleted file mode 100644
> index f709304036c2..000000000000
> --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt
> +++ /dev/null
> @@ -1,73 +0,0 @@
> -NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver.
> -
> -Required properties:
> -- compatible : should be,
> -  "nvidia,tegra20-hsuart" for Tegra20,
> -  "nvidia,tegra30-hsuart" for Tegra30,
> -  "nvidia,tegra186-hsuart" for Tegra186,
> -  "nvidia,tegra194-hsuart" for Tegra194.
> -
> -- reg: Should contain UART controller registers location and length.
> -- interrupts: Should contain UART controller interrupts.
> -- clocks: Must contain one entry, for the module clock.
> -  See ../clocks/clock-bindings.txt for details.
> -- resets : Must contain an entry for each entry in reset-names.
> -  See ../reset/reset.txt for details.
> -- reset-names : Must include the following entries:
> -  - serial
> -- dmas : Must contain an entry for each entry in dma-names.
> -  See ../dma/dma.txt for details.
> -- dma-names : Must include the following entries:
> -  - rx
> -  - tx
> -
> -Optional properties:
> -- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable
> -		only if all 8 lines of UART controller are pinmuxed.
> -- nvidia,adjust-baud-rates: List of entries providing percentage of baud rate
> -  adjustment within a range.
> -  Each entry contains sets of 3 values. Range low/high and adjusted rate.
> -  <range_low range_high adjusted_rate>
> -  When baud rate set on controller falls within the range mentioned in this
> -  field, baud rate will be adjusted by percentage mentioned here.
> -  Ex: <9600 115200 200>
> -  Increase baud rate by 2% when set baud rate falls within range 9600 to 115200
> -
> -Baud Rate tolerance:
> -  Standard UART devices are expected to have tolerance for baud rate error by
> -  -4 to +4 %. All Tegra devices till Tegra210 had this support. However,
> -  Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level
> -  is 0% to +4% in 1-stop config. Otherwise, the received data will have
> -  corruption/invalid framing errors. Parker errata suggests adjusting baud
> -  rate to be higher than the deviations observed in Tx.
> -
> -  Tx deviation of connected device can be captured over scope (or noted from
> -  its spec) for valid range and Tegra baud rate has to be set above actual
> -  Tx baud rate observed. To do this we use nvidia,adjust-baud-rates
> -
> -  As an example, consider there is deviation observed in Tx for baud rates as
> -  listed below.
> -  0 to 9600 has 1% deviation
> -  9600 to 115200 2% deviation
> -  This slight deviation is expcted and Tegra UART is expected to handle it. Due
> -  to the issue stated above, baud rate on Tegra UART should be set equal to or
> -  above deviation observed for avoiding frame errors.
> -  Property should be set like this
> -  nvidia,adjust-baud-rates = <0 9600 100>,
> -  			     <9600 115200 200>;
> -
> -Example:
> -
> -serial@70006000 {
> -	compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart";

I guess this wasn't valid? Would be good if the commit msg said that.

> -	reg = <0x70006000 0x40>;
> -	reg-shift = <2>;
> -	interrupts = <0 36 0x04>;
> -	nvidia,enable-modem-interrupt;
> -	clocks = <&tegra_car 6>;
> -	resets = <&tegra_car 6>;
> -	reset-names = "serial";
> -	dmas = <&apbdma 8>, <&apbdma 8>;
> -	dma-names = "rx", "tx";
> -	nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */
> -};
> diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml
> new file mode 100644
> index 000000000000..247ee33f8a01
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml
> @@ -0,0 +1,124 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/serial/nvidia,tegra20-hsuart.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver
> +
> +maintainers:
> +  - Thierry Reding <thierry.reding@xxxxxxxxx>
> +  - Jon Hunter <jonathanh@xxxxxxxxxx>
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - const: nvidia,tegra20-hsuart
> +      - const: nvidia,tegra30-hsuart
> +      - items:
> +          - const: nvidia,tegra124-hsuart
> +          - const: nvidia,tegra30-hsuart
> +      - const: nvidia,tegra186-hsuart
> +      - const: nvidia,tegra194-hsuart

All the single entry entries can be an enum.

With those fixes:

Reviewed-by: Rob Herring <robh@xxxxxxxxxx>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux