Re: [PATCH v12 04/10] dt-bindings: soc: qcom: cpr3: Add bindings for CPR3 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jun 28, 2023 at 04:00:43PM +0200, Konrad Dybcio wrote:
> From: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
> 
> Add the bindings for the CPR3 driver to the documentation.

Bindings are for h/w, not drivers.

> 
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
> [Konrad: Make binding check pass; update AGdR's email]
> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/soc/qcom/qcom,cpr3.yaml    | 289 +++++++++++++++++++++
>  1 file changed, 289 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,cpr3.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,cpr3.yaml
> new file mode 100644
> index 000000000000..46b94dffaf85
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,cpr3.yaml
> @@ -0,0 +1,289 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/soc/qcom/qcom,cpr3.yaml#";
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#";

Drop quotes

> +
> +title: Qualcomm Core Power Reduction v3/v4/Hardened (CPR3, CPR4, CPRh)
> +
> +description:
> +  CPR (Core Power Reduction) is a technology to reduce core power of a CPU
> +  (or another device). Each OPP of a device corresponds to a "corner" that
> +  has a range of valid voltages for a particular frequency.
> +  The CPR monitors dynamic factors such as temperature, etc. and suggests
> +  or (in the CPR-hardened case) applies voltage adjustments to save power
> +  and meet silicon characteristic requirements for a given chip unit.
> +
> +maintainers:
> +  - AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - description: CPRv3 controller
> +        items:
> +          - const: qcom,cpr3
> +      - description: CPRv4 controller
> +        items:
> +          - const: qcom,cpr4
> +      - description: CPRv4-Hardened controller
> +        items:
> +          - enum:
> +              - qcom,msm8998-cprh
> +              - qcom,sdm630-cprh
> +          - const: qcom,cprh
> +
> +  reg:
> +    description: Base address and size of the CPR controller(s)
> +    maxItems: 2

What is each entry?

> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: CPR reference clock
> +
> +  vdd-supply:
> +    description: Autonomous Phase Control (APC) or other power supply
> +
> +  '#power-domain-cells':
> +    const: 1
> +
> +  qcom,acc:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: phandle to syscon for writing ACC settings
> +
> +  nvmem-cells:
> +    description: Cells containing the fuse corners and revision data
> +    maxItems: 32
> +
> +  nvmem-cell-names:
> +    maxItems: 32
> +
> +  operating-points-v2: true
> +
> +  power-domains: true

Need to define how many.

> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - operating-points-v2
> +  - "#power-domain-cells"
> +  - nvmem-cells
> +  - nvmem-cell-names
> +
> +additionalProperties: false
> +
> +allOf:
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - qcom,msm8998-cprh
> +    then:
> +      properties:
> +        nvmem-cell-names:
> +          items:
> +            - const: cpr_speed_bin
> +            - const: cpr_fuse_revision
> +            - const: cpr0_quotient1
> +            - const: cpr0_quotient2
> +            - const: cpr0_quotient3
> +            - const: cpr0_quotient4
> +            - const: cpr0_quotient_offset2
> +            - const: cpr0_quotient_offset3
> +            - const: cpr0_quotient_offset4
> +            - const: cpr0_init_voltage1
> +            - const: cpr0_init_voltage2
> +            - const: cpr0_init_voltage3
> +            - const: cpr0_init_voltage4
> +            - const: cpr0_ring_osc1
> +            - const: cpr0_ring_osc2
> +            - const: cpr0_ring_osc3
> +            - const: cpr0_ring_osc4
> +            - const: cpr1_quotient1
> +            - const: cpr1_quotient2
> +            - const: cpr1_quotient3
> +            - const: cpr1_quotient4
> +            - const: cpr1_quotient_offset2
> +            - const: cpr1_quotient_offset3
> +            - const: cpr1_quotient_offset4
> +            - const: cpr1_init_voltage1
> +            - const: cpr1_init_voltage2
> +            - const: cpr1_init_voltage3
> +            - const: cpr1_init_voltage4
> +            - const: cpr1_ring_osc1
> +            - const: cpr1_ring_osc2
> +            - const: cpr1_ring_osc3
> +            - const: cpr1_ring_osc4
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,gcc-msm8998.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    cpus {
> +        #address-cells = <2>;
> +        #size-cells = <0>;
> +
> +        cpu@0 {
> +            compatible = "qcom,kryo280";
> +            device_type = "cpu";
> +            reg = <0x0 0x0>;
> +            operating-points-v2 = <&cpu0_opp_table>;
> +            power-domains = <&apc_cprh 0>;
> +            power-domain-names = "cprh";

The name should be local to the device, not based on the provider.

Do you really need a name here with only 1? 

> +        };
> +
> +        cpu@100 {
> +            compatible = "qcom,kryo280";
> +            device_type = "cpu";
> +            reg = <0x0 0x100>;
> +            operating-points-v2 = <&cpu4_opp_table>;
> +            power-domains = <&apc_cprh 1>;
> +            power-domain-names = "cprh";
> +        };
> +    };
> +
> +    cpu0_opp_table: opp-table-cpu0 {
> +        compatible = "operating-points-v2";
> +        opp-shared;
> +
> +        opp-1843200000 {
> +            opp-hz = /bits/ 64 <1843200000>;
> +            required-opps = <&cprh_opp3>;
> +        };
> +
> +        opp-1094400000 {
> +            opp-hz = /bits/ 64 <1094400000>;
> +            required-opps = <&cprh_opp2>;
> +        };
> +
> +        opp-300000000 {
> +            opp-hz = /bits/ 64 <300000000>;
> +            required-opps = <&cprh_opp1>;
> +        };
> +    };
> +
> +    cpu4_opp_table: opp-table-cpu4 {
> +        compatible = "operating-points-v2";
> +        opp-shared;
> +
> +        opp-2208000000 {
> +            opp-hz = /bits/ 64 <2208000000>;
> +            required-opps = <&cprh_opp3>;
> +        };
> +
> +        opp-1113600000 {
> +            opp-hz = /bits/ 64 <1113600000>;
> +            required-opps = <&cprh_opp2>;
> +        };
> +
> +        opp-300000000 {
> +            opp-hz = /bits/ 64 <300000000>;
> +            required-opps = <&cprh_opp1>;
> +        };
> +    };
> +
> +    cprh_opp_table: opp-table-cprh {
> +        compatible = "operating-points-v2-qcom-level";
> +
> +        cprh_opp1: opp-1 {
> +            opp-level = <1>;
> +            qcom,opp-fuse-level = <1>;
> +            qcom,opp-cloop-vadj = <0>;
> +            qcom,opp-oloop-vadj = <0>;
> +        };
> +
> +        cprh_opp2: opp-2 {
> +            opp-level = <2>;
> +            qcom,opp-fuse-level = <2>;
> +            qcom,opp-cloop-vadj = <0>;
> +            qcom,opp-oloop-vadj = <0>;
> +        };
> +
> +        cprh_opp3: opp-3 {
> +            opp-level = <3>;
> +            qcom,opp-fuse-level = <2 3>;
> +            qcom,opp-cloop-vadj = <0>;
> +            qcom,opp-oloop-vadj = <0>;
> +        };
> +    };
> +
> +    apc_cprh: power-controller@179c8000 {
> +        compatible = "qcom,msm8998-cprh", "qcom,cprh";
> +        reg = <0x0179c8000 0x4000>, <0x0179c4000 0x4000>;
> +        clocks = <&gcc GCC_HMSS_RBCPR_CLK>;
> +
> +        operating-points-v2 = <&cprh_opp_table>;
> +        #power-domain-cells = <1>;
> +
> +        nvmem-cells = <&cpr_efuse_speedbin>,
> +                      <&cpr_fuse_revision>,
> +                      <&cpr_quot0_pwrcl>,
> +                      <&cpr_quot1_pwrcl>,
> +                      <&cpr_quot2_pwrcl>,
> +                      <&cpr_quot3_pwrcl>,
> +                      <&cpr_quot_offset1_pwrcl>,
> +                      <&cpr_quot_offset2_pwrcl>,
> +                      <&cpr_quot_offset3_pwrcl>,
> +                      <&cpr_init_voltage0_pwrcl>,
> +                      <&cpr_init_voltage1_pwrcl>,
> +                      <&cpr_init_voltage2_pwrcl>,
> +                      <&cpr_init_voltage3_pwrcl>,
> +                      <&cpr_ro_sel0_pwrcl>,
> +                      <&cpr_ro_sel1_pwrcl>,
> +                      <&cpr_ro_sel2_pwrcl>,
> +                      <&cpr_ro_sel3_pwrcl>,
> +                      <&cpr_quot0_perfcl>,
> +                      <&cpr_quot1_perfcl>,
> +                      <&cpr_quot2_perfcl>,
> +                      <&cpr_quot3_perfcl>,
> +                      <&cpr_quot_offset1_perfcl>,
> +                      <&cpr_quot_offset2_perfcl>,
> +                      <&cpr_quot_offset3_perfcl>,
> +                      <&cpr_init_voltage0_perfcl>,
> +                      <&cpr_init_voltage1_perfcl>,
> +                      <&cpr_init_voltage2_perfcl>,
> +                      <&cpr_init_voltage3_perfcl>,
> +                      <&cpr_ro_sel0_perfcl>,
> +                      <&cpr_ro_sel1_perfcl>,
> +                      <&cpr_ro_sel2_perfcl>,
> +                      <&cpr_ro_sel3_perfcl>;
> +        nvmem-cell-names = "cpr_speed_bin",
> +                           "cpr_fuse_revision",
> +                           "cpr0_quotient1",
> +                           "cpr0_quotient2",
> +                           "cpr0_quotient3",
> +                           "cpr0_quotient4",
> +                           "cpr0_quotient_offset2",
> +                           "cpr0_quotient_offset3",
> +                           "cpr0_quotient_offset4",
> +                           "cpr0_init_voltage1",
> +                           "cpr0_init_voltage2",
> +                           "cpr0_init_voltage3",
> +                           "cpr0_init_voltage4",
> +                           "cpr0_ring_osc1",
> +                           "cpr0_ring_osc2",
> +                           "cpr0_ring_osc3",
> +                           "cpr0_ring_osc4",
> +                           "cpr1_quotient1",
> +                           "cpr1_quotient2",
> +                           "cpr1_quotient3",
> +                           "cpr1_quotient4",
> +                           "cpr1_quotient_offset2",
> +                           "cpr1_quotient_offset3",
> +                           "cpr1_quotient_offset4",
> +                           "cpr1_init_voltage1",
> +                           "cpr1_init_voltage2",
> +                           "cpr1_init_voltage3",
> +                           "cpr1_init_voltage4",
> +                           "cpr1_ring_osc1",
> +                           "cpr1_ring_osc2",
> +                           "cpr1_ring_osc3",
> +                           "cpr1_ring_osc4";
> +    };
> +...
> 
> -- 
> 2.41.0
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux