From: Haibo Chen <haibo.chen@xxxxxxx>
Add 100MHz and 200MHz pinctrl setting for eMMC, and enable 8 bit bus mode
to config the eMMC work at HS400ES mode.
Also update to use Standard Drive Strength for USDHC pad to get a better
signal quality per Hardware team suggests.
Reviewed-by: Sherry Sun <sherry.sun@xxxxxxx>
Signed-off-by: Haibo Chen <haibo.chen@xxxxxxx>
Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
---
arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 26 ++++++++++---------
1 file changed, 14 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
index e459dc35e469..ab7af705bbca 100644
--- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
@@ -121,9 +121,11 @@ &lpuart5 {
};
&usdhc0 {
- pinctrl-names = "default", "sleep";
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
pinctrl-0 = <&pinctrl_usdhc0>;
pinctrl-1 = <&pinctrl_usdhc0>;
+ pinctrl-2 = <&pinctrl_usdhc0>;
+ pinctrl-3 = <&pinctrl_usdhc0>;
non-removable;
bus-width = <8>;
status = "okay";
@@ -202,17 +204,17 @@ MX8ULP_PAD_PTF15__LPUART5_RX 0x3
pinctrl_usdhc0: usdhc0grp {
fsl,pins = <
- MX8ULP_PAD_PTD1__SDHC0_CMD 0x43
- MX8ULP_PAD_PTD2__SDHC0_CLK 0x10042
- MX8ULP_PAD_PTD10__SDHC0_D0 0x43
- MX8ULP_PAD_PTD9__SDHC0_D1 0x43
- MX8ULP_PAD_PTD8__SDHC0_D2 0x43
- MX8ULP_PAD_PTD7__SDHC0_D3 0x43
- MX8ULP_PAD_PTD6__SDHC0_D4 0x43
- MX8ULP_PAD_PTD5__SDHC0_D5 0x43
- MX8ULP_PAD_PTD4__SDHC0_D6 0x43
- MX8ULP_PAD_PTD3__SDHC0_D7 0x43
- MX8ULP_PAD_PTD11__SDHC0_DQS 0x10042
+ MX8ULP_PAD_PTD1__SDHC0_CMD 0x3
+ MX8ULP_PAD_PTD2__SDHC0_CLK 0x10002
+ MX8ULP_PAD_PTD10__SDHC0_D0 0x3
+ MX8ULP_PAD_PTD9__SDHC0_D1 0x3
+ MX8ULP_PAD_PTD8__SDHC0_D2 0x3
+ MX8ULP_PAD_PTD7__SDHC0_D3 0x3
+ MX8ULP_PAD_PTD6__SDHC0_D4 0x3
+ MX8ULP_PAD_PTD5__SDHC0_D5 0x3
+ MX8ULP_PAD_PTD4__SDHC0_D6 0x3
+ MX8ULP_PAD_PTD3__SDHC0_D7 0x3
+ MX8ULP_PAD_PTD11__SDHC0_DQS 0x10002
>;
};
};
--
2.37.1
