Re: [PATCH 7/9] arm64: dts: qcom: ipq5332: Add USB related nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jun 07, 2023 at 08:35:09PM +0200, Krzysztof Kozlowski wrote:
> On 07/06/2023 12:56, Varadarajan Narayanan wrote:
> > Add USB phy and controller nodes
> >
> > Signed-off-by: Varadarajan Narayanan <quic_varada@xxxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/ipq5332.dtsi | 55 +++++++++++++++++++++++++++++++++++
> >  1 file changed, 55 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> > index c2d6cc65..3183357 100644
> > --- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> > @@ -383,6 +383,61 @@
> >  				status = "disabled";
> >  			};
> >  		};
> > +
> > +		usb_0_m31phy: hs_m31phy@7b000 {
>
> Node names should be generic. See also explanation and list of examples
> in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Ok.

> > +			compatible = "qcom,ipq5332-m31-usb-hsphy";
> > +			reg = <0x0007b000 0x12C>,
> > +			      <0x08af8800 0x400>;
>
> Lowercase hex only.

Ok.

> > +			reg-names = "m31usb_phy_base",
> > +				    "qscratch_base";
> > +			phy_type= "utmi";
> > +
> > +			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
> > +			reset-names = "usb2_phy_reset";
> > +
> > +			status = "okay";
>
> It's by default. Drop.

Ok.

> > +		};
> > +
> > +		usb2: usb2@8a00000 {
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check` (see
> Documentation/devicetree/bindings/writing-schema.rst for instructions).
>
> Node names should be generic. See also explanation and list of examples
> in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Ok.

> > +			compatible = "qcom,ipq5332-dwc3", "qcom,dwc3";
> > +			#address-cells = <1>;
> > +			#size-cells = <1>;
> > +			ranges;
> > +
> > +			reg = <0x08af8800 0x100>;
>
> reg is always after compatible. Ranges is third. Then you will spot that
> address is wrong.

Ok.

> > +
> > +			clocks = <&gcc GCC_USB0_MASTER_CLK>,
> > +				<&gcc GCC_SNOC_USB_CLK>,
> > +				<&gcc GCC_USB0_SLEEP_CLK>,
> > +				<&gcc GCC_USB0_MOCK_UTMI_CLK>;
>
> Fix alignment.

Ok.

> > +
> > +			clock-names = "core",
> > +				"iface",
> > +				"sleep",
> > +				"mock_utmi";
>
> Fix alignment.

Ok.

> > +
> > +			interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
> > +			interrupt-names = "pwr_event";
> > +

Thanks
Varada

> Best regards,
> Krzysztof
>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux