Re: [PATCH v1 8/8] ARM: dts: stm32: lxa-tac: add Linux Automation GmbH TAC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 08.06.23 15:13, Alexandre TORGUE wrote:
Hi Leonard

On 6/7/23 13:55, Leonard Göhrs wrote:
The Linux Automation Test Automation Controller (LXA TAC)[1] is an embedded
software development tool built around the Octavo Systems OSD32MP15x SiP.

The device contains an eMMC for storage, a DSA-capable on board ethernet
switch with two external ports, dual CAN busses, a power switch to turn
a device under test on or off and some other I/O.

As of now there are two STM32MP157 based hardware generations (Gen 1 and
Gen 2) that have most of their hardware config in common.
In the future there will also be a STM32MP153 based hardware generation.

[1]: https://www.linux-automation.com/en/products/lxa-tac.html

Signed-off-by: Leonard Göhrs <l.goehrs@xxxxxxxxxxxxxx>
---

There are some YAML issues reported. Some are linked to the
stm32mp151.dts or common bindings and are going to be fixed. But some
looks more linked to your board. Can you have a look on those:

Most of these should be addressed by the other patches in the series,
that add devicetree bindings for things we use in the LXA TAC devicetree.

arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dtb: gpio@24:
'gpio-line-names' does not match any of the regexes: 'pinctrl-[0-9]+'
	From schema: /Documentation/devicetree/bindings/gpio/gpio-pca9570.yaml

The patch to add this property is now in gpio/for-next.

arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dtb: display@0: compatible:0:
'shineworld,lh133k' is not one of ['sainsmart18']
	From schema:
/Documentation/devicetree/bindings/display/panel/panel-mipi-dbi-spi.yaml

arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dtb: display@0: Unevaluated
properties are not allowed ('compatible', 'spi-3wire' were unexpected)
	From schema:
/Documentation/devicetree/bindings/display/panel/panel-mipi-dbi-spi.yaml> arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dtb:
/soc/spi@44005000/display@0: failed to match any schema with compatible:
['shineworld,lh133k', 'panel-mipi-dbi-spi']

Bindings for these properties are added in previous patches in this series
(which are not yet applied anywhere).

/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dtb: switch@0: Unevaluated
properties are not allowed ('spi-cpha', 'spi-cpol', 'interrupt-parent',
'interrupts' were unexpected)
	From schema: /Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml

The 'spi-cpha' and 'spi-cpol' properties were not actually required, so I've
dropped them from the devicetree for the V2 I've just sent.
I've added a patch that adds bindings for 'interrupts' to the V2, so this should
be addressed as well.

arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dtb: can@4400f000:
'termination-gpios', 'termination-ohms' do not match any of the regexes:
'pinctrl-[0-9]+'
	From schema: /Documentation/devicetree/bindings/net/can/bosch,m_can.yaml

This should also be addressed in the V2.

Thanks in advance

Thanks for checking out my patch!


Alex


   arch/arm/boot/dts/Makefile                    |   2 +
   .../arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts |  93 +++
   .../arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts | 172 +++++
   arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi    | 612 ++++++++++++++++++
   4 files changed, 879 insertions(+)
   create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
   create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
   create mode 100644 arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 59829fc903152..886371436bbc1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1266,6 +1266,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
   	stm32mp157c-ev1.dtb \
   	stm32mp157c-ev1-scmi.dtb \
   	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-lxa-tac-gen1.dtb \
+	stm32mp157c-lxa-tac-gen2.dtb \
   	stm32mp157c-odyssey.dtb
   dtb-$(CONFIG_MACH_SUN4I) += \
   	sun4i-a10-a1000.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
new file mode 100644
index 0000000000000..81f254fb88b0a
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 1";
+	compatible = "lxa,stm32mp157c-tac-gen1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&backlight_pwm 1 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+
+		gpio = <&gpioh 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "STACK_CS2", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                     /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",             /* 10 */
+	"";                                                     /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "STACK_CS1", "", "", "", /*  0 */
+	"", "", "", "", "",                            /*  5 */
+	"", "";                                        /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&i2c1 {
+	powerboard_gpio: gpio@24 {
+		compatible = "nxp,pca9570";
+		reg = <0x24>;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names = "DUT_PWR_EN", "DUT_PWR_DISCH", "DUT_PWR_ADCRST", "";
+	};
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+		reset-gpios = <&powerboard_gpio 2 GPIO_ACTIVE_HIGH>;
+
+		shunt-resistor-micro-ohms = <15000>;
+	};
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	backlight_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm1_pins_c>;
+		pinctrl-1 = <&pwm1_sleep_pins_c>;
+
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
new file mode 100644
index 0000000000000..8a34d15e9005f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 2";
+	compatible = "lxa,stm32mp157c-tac-gen2", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&led_pwm 3 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+		gpio = <&gpioh 13 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds-multicolor";
+
+		multi-led {
+			color = <LED_COLOR_ID_RGB>;
+			function = LED_FUNCTION_STATUS;
+			max-brightness = <65535>;
+
+			led-red {
+				active-low;
+				color = <LED_COLOR_ID_RED>;
+				pwms = <&led_pwm 0 1000000 0>;
+			};
+
+			led-green {
+				active-low;
+				color = <LED_COLOR_ID_GREEN>;
+				pwms = <&led_pwm 2 1000000 0>;
+			};
+
+			led-blue {
+				active-low;
+				color = <LED_COLOR_ID_BLUE>;
+				pwms = <&led_pwm 1 1000000 0>;
+			};
+		};
+	};
+
+	led-controller-2 {
+		compatible = "gpio-leds";
+
+		led-5 {
+			label = "tac:green:iobus";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-6 {
+			label = "tac:green:can";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-7 {
+			label = "tac:green:out0";
+			gpios = <&gpiob 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-8 {
+			label = "tac:green:out1";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-9 {
+			label = "tac:green:uarttx";
+			gpios = <&gpiod 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-10 {
+			label = "tac:green:uartrx";
+			gpios = <&gpiof 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-11 {
+			label = "tac:green:usbh1";
+			gpios = <&gpioc 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-12 {
+			label = "tac:green:usbh2";
+			gpios = <&gpiod 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-13 {
+			label = "tac:green:usbh3";
+			gpios = <&gpiob 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-14 {
+			label = "tac:green:usbg";
+			gpios = <&gpiod 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-gadget";
+		};
+
+		led-15 {
+			label = "tac:green:dutpwr";
+			gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "DUT_PWR_EN", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                      /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",              /* 10 */
+	"";                                                      /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "DUT_PWR_DISCH", "", "", "", /*  0 */
+	"", "", "", "", "",                                /*  5 */
+	"", "";                                            /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&m_can2 {
+	termination-gpios = <&gpioe 4 GPIO_ACTIVE_HIGH>;
+	termination-ohms = <120>;
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+
+		reset-gpios = <&gpioa 4 GPIO_ACTIVE_HIGH>;
+		shunt-resistor-micro-ohms = <15000>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+	};
+};
+
+&timers8 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	led_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm8_pins_b>;
+		pinctrl-1 = <&pwm8_sleep_pins_b>;
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi b/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
new file mode 100644
index 0000000000000..ca4d25f5c9b51
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &port_uplink;
+		ethernet2 = &port_dut;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &usart3;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "tac:green:user1";
+			gpios = <&gpiof 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "tac:green:user2";
+			gpios = <&gpiog 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "tac:green:statusdut";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* led-3 and led-4 are internally connected antiparallel to one
+		 * another inside the ethernet jack like this:
+		 * GPIOA14 ---+---|led-3|>--+--- GPIOD15
+		 *            +--<|led-4|---+
+		 * E.g. only one of the LEDs can be illuminated at a time while
+		 * the other output must be driven low.
+		 * This should likely be implemented using a multi color LED
+		 * driver for antiparallel LEDs.
+		 */
+		led-3 {
+			label = "tac:green:statuslab";
+			gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "tac:orange:statuslab";
+			gpios = <&gpiod 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-lower {
+			label = "USER_BTN2";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+
+		button-upper {
+			label = "USER_BTN";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+
+	/* supplied by either barrel connector or PoE */
+	reg_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_1v2: regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_pb_5v: regulator-pb-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_POWERBOARD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_pb_3v3: regulator-pb-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_POWERBOARD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_pb_5v>;
+	};
+
+	output-iobus-12v {
+		compatible = "regulator-output";
+		vout-supply = <&reg_iobus_12v>;
+	};
+
+	output-vuart {
+		compatible = "regulator-output";
+		vout-supply = <&v3v3_hdmi>;
+	};
+};
+
+baseboard_eeprom: &sip_eeprom {
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_ain_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 2 5 9 10 13 15>;
+		st,min-sample-time-nsecs = <5000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@0 {
+			reg = <0>;
+			label = "HOST_2_CURR_FB";
+		};
+
+		channel@1 {
+			reg = <1>;
+			label = "HOST_3_CURR_FB";
+		};
+
+		channel@2 {
+			reg = <2>;
+			label = "OUT_0_FB";
+		};
+
+		channel@5 {
+			reg = <5>;
+			label = "IOBUS_CURR_FB";
+		};
+
+		channel@9 {
+			reg = <9>;
+			label = "IOBUS_VOLT_FB";
+		};
+
+		channel@10 {
+			reg = <10>;
+			label = "OUT_1_FB";
+		};
+
+		channel@13 {
+			reg = <13>;
+			label = "HOST_CURR_FB";
+		};
+
+		channel@15 {
+			reg = <15>;
+			label = "HOST_1_CURR_FB";
+		};
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <12>;
+		st,min-sample-time-nsecs = <500000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@12 {
+			reg = <12>;
+			label = "TEMP_INTERNAL";
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_d>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_d>;
+
+	st,eth-clk-sel;
+	phy-mode = "rgmii-id";
+
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&ethernet0_rgmii_pins_d {
+	pins1 {
+		/* Reduce EMI emission by reducing RGMII drive strength */
+		slew-rate = <1>;
+	};
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "", "", /*  0 */
+	"", "USB_RESET", "", "", "",          /*  5 */
+	"", "", "", "", "",                   /* 10 */
+	"";                                   /* 15 */
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "", "TP38", /*  0 */
+	"TP39", "", "", "TP41", "TP42",           /*  5 */
+	"OLED_DC", "", "", "ETH_CS", "",          /* 10 */
+	"ETH_LAB_LEDRN";                          /* 15 */
+};
+
+&gpioe {
+	gpio-line-names = "TP35", "", "", "", "CAN_1_120R", /*  0 */
+	"", "", "USER_BTN2", "TP48", "UART_TX_EN",          /*  5 */
+	"UART_RX_EN", "TP24", "", "TP25", "TP26",           /* 10 */
+	"TP27";                                             /* 15 */
+};
+
+&gpiof {
+	gpio-line-names = "TP36", "TP37", "", "", "OLED_CS", /*  0 */
+	"", "", "", "", "",                                  /*  5 */
+	"USER_LED1", "", "STACK_CS0", "", "",                /* 10 */
+	"";                                                  /* 15 */
+};
+
+&gpiog {
+	gpio-line-names = "ETH_RESET", "", "", "", "",               /*  0 */
+	"IOBUS_FLT_FB", "", "USER_LED2", "ETH1_PPS_A", "CAN_0_120R", /*  5 */
+	"TP49", "", "", "", "",                                      /* 10 */
+	"";                                                          /* 15 */
+};
+
+&gpioh {
+	gpio-line-names = "", "", "OUT_1", "OUT_0", "OLED_RESET", /*  0 */
+	"", "", "", "", "",                                       /*  5 */
+	"ETH1_PPS_B", "ETH_GPIO2", "", "IOBUS_PWR_EN", "",        /* 10 */
+	"TP33";                                                   /* 15 */
+};
+
+&gpioi {
+	gpio-line-names = "TIM_RTS", "", "", "", "DEVICE_DATA_EN", /*  0 */
+	"", "", "", "ETH_WOL", "TP43",                             /*  5 */
+	"", "USER_BTN";                                            /* 10 */
+};
+
+&gpioz {
+	gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /*  0 */
+	"", "HWID4", "HWID5";                                     /*  5 */
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	status = "okay";
+
+	powerboard_eeprom: eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		vcc-supply = <&v3v3>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+		status = "disabled";
+	};
+};
+
+&i2c5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_b>;
+	pinctrl-1 = <&i2c5_sleep_pins_b>;
+
+	status = "okay";
+
+	usbhub: usbhub@2c {
+		compatible ="microchip,usb2514b";
+		reg = <0x2c>;
+		vdd-supply = <&v3v3>;
+		reset-gpios = <&gpiob 6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <8>;
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
+
+&pmic {
+	regulators {
+		buck1-supply = <&reg_5v>;	/* VIN */
+		buck2-supply = <&reg_5v>;	/* VIN */
+		buck3-supply = <&reg_5v>;	/* VIN */
+		buck4-supply = <&reg_5v>;	/* VIN */
+		ldo2-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		ldo4-supply = <&reg_5v>;	/* VIN */
+		ldo5-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		vref_ddr-supply = <&reg_5v>;	/* VIN */
+		boost-supply = <&reg_5v>;	/* PMIC_BSTIN */
+		pwr_sw2-supply = <&bst_out>;	/* PMIC_SWIN */
+	};
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+	vmmc-supply = <&v3v3>;
+
+	bus-width = <8>;
+	mmc-ddr-3_3v;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+
+	status = "okay";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_c>;
+	cs-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&spi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins_a>;
+	cs-gpios = <&gpiof 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	lcd: display@0 {
+		compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
+		reg = <0>;
+		power-supply = <&v3v3>;
+		io-supply = <&v3v3>;
+		backlight = <&backlight>;
+		dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
+		spi-3wire;
+		spi-max-frequency = <32000000>;
+
+		width-mm = <23>;
+		height-mm = <23>;
+		rotation = <180>;
+
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <0>;
+			vback-porch = <0>;
+
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&spi5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi5_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	cs-gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+
+	switch: switch@0 {
+		compatible = "microchip,ksz9563";
+		reg = <0>;
+
+		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <44000000>;
+		spi-cpha;
+		spi-cpol;
+
+		interrupt-parent = <&gpioa>;
+		interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port_dut: port@0 {
+				reg = <0>;
+				label = "dut";
+			};
+
+			port_uplink: port@1 {
+				reg = <1>;
+				label = "uplink";
+			};
+
+			port_cpu: port@2 {
+				reg = <2>;
+				label = "cpu";
+
+				ethernet = <&ethernet0>;
+
+				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	label = "debug";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usart3 {
+	label = "dut";
+	uart-has-rtscts;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_f>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+
+	vusb_d-supply = <&vdd_usb>;
+	vusb_a-supply = <&reg18>;
+
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&v3v3_hdmi {
+	/delete-property/regulator-always-on;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdda>;
+
+	status = "okay";
+};





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux