On Thu, Jun 8, 2023 at 10:28 AM Yinbo Zhu <zhuyinbo@xxxxxxxxxxx> wrote:
>
> This bus driver supports the Loongson SPI hardware controller in the
> Loongson platforms and supports to use DTS and PCI framework to
the use
> register SPI device resources.
Thank you for an update. I have a few nit-picks below, but in general
this version is good (esp. if you address them)
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
> Signed-off-by: Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
> Cc: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
> Cc: Mark Brown <broonie@xxxxxxxxxx>
> ---
> MAINTAINERS | 4 +
> drivers/spi/Kconfig | 26 +++
> drivers/spi/Makefile | 3 +
> drivers/spi/spi-loongson-core.c | 275 ++++++++++++++++++++++++++++++++
> drivers/spi/spi-loongson-pci.c | 55 +++++++
> drivers/spi/spi-loongson-plat.c | 47 ++++++
> drivers/spi/spi-loongson.h | 49 ++++++
> 7 files changed, 459 insertions(+)
> create mode 100644 drivers/spi/spi-loongson-core.c
> create mode 100644 drivers/spi/spi-loongson-pci.c
> create mode 100644 drivers/spi/spi-loongson-plat.c
> create mode 100644 drivers/spi/spi-loongson.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 5e604dddd87b..69cb8fb2a0e1 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12191,6 +12191,10 @@ M: Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
> L: linux-spi@xxxxxxxxxxxxxxx
> S: Maintained
> F: Documentation/devicetree/bindings/spi/loongson,ls2k-spi.yaml
> +F: drivers/spi/spi-loongson-core.c
> +F: drivers/spi/spi-loongson-pci.c
> +F: drivers/spi/spi-loongson-plat.c
> +F: drivers/spi/spi-loongson.h
>
> LOONGSON-2 SOC SERIES GUTS DRIVER
> M: Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index 3de2ebe8294a..6b953904792e 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -516,6 +516,32 @@ config SPI_LM70_LLP
> which interfaces to an LM70 temperature sensor using
> a parallel port.
>
> +config SPI_LOONGSON_CORE
> + tristate
> + depends on LOONGARCH || COMPILE_TEST
> +
> +config SPI_LOONGSON_PCI
> + tristate "Loongson SPI Controller PCI Driver Support"
> + select SPI_LOONGSON_CORE
> + depends on PCI && (LOONGARCH || COMPILE_TEST)
> + help
> + This bus driver supports the Loongson SPI hardware controller in
> + the Loongson platforms and supports to use PCI framework to
> + register SPI device resources.
> + Say Y or M here if you want to use the SPI controller on
> + Loongson platform.
> +
> +config SPI_LOONGSON_PLATFORM
> + tristate "Loongson SPI Controller Platform Driver Support"
> + select SPI_LOONGSON_CORE
> + depends on OF && (LOONGARCH || COMPILE_TEST)
> + help
> + This bus driver supports the Loongson SPI hardware controller in
> + the Loongson platforms and supports to use DTS framework to
> + register SPI device resources.
> + Say Y or M here if you want to use the SPI controller on
> + Loongson platform.
> +
> config SPI_LP8841_RTC
> tristate "ICP DAS LP-8841 SPI Controller for RTC"
> depends on MACH_PXA27X_DT || COMPILE_TEST
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 28c4817a8a74..3e933064d237 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -71,6 +71,9 @@ obj-$(CONFIG_SPI_INTEL_PLATFORM) += spi-intel-platform.o
> obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
> obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
> obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
> +obj-$(CONFIG_SPI_LOONGSON_CORE) += spi-loongson-core.o
> +obj-$(CONFIG_SPI_LOONGSON_PCI) += spi-loongson-pci.o
> +obj-$(CONFIG_SPI_LOONGSON_PLATFORM) += spi-loongson-plat.o
> obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
> obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
> obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
> diff --git a/drivers/spi/spi-loongson-core.c b/drivers/spi/spi-loongson-core.c
> new file mode 100644
> index 000000000000..403b735bd0cf
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-core.c
> @@ -0,0 +1,275 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Loongson SPI Support
> +// Copyright (C) 2023 Loongson Technology Corporation Limited
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/spi/spi.h>
> +
> +#include "spi-loongson.h"
> +
> +static inline void loongson_spi_write_reg(struct loongson_spi *spi, unsigned char reg,
> + unsigned char data)
> +{
> + writeb(data, spi->base + reg);
> +}
> +
> +static inline char loongson_spi_read_reg(struct loongson_spi *spi, unsigned char reg)
> +{
> + return readb(spi->base + reg);
> +}
> +
> +static void loongson_spi_set_cs(struct spi_device *spi, bool val)
> +{
> + int cs;
> + struct loongson_spi *loongson_spi = spi_controller_get_devdata(spi->controller);
> +
> + cs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG)
> + & ~(0x11 << spi_get_chipselect(spi, 0));
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
> + (val ? (0x11 << spi_get_chipselect(spi, 0)) :
> + (0x1 << spi_get_chipselect(spi, 0))) | cs);
Can be done as
static void loongson_spi_set_cs(struct spi_device *spi, bool en)
unsigned char mask = (BIT(4) | BIT(0)) << spi_get_chipselect(spi, 0);
unsigned char val = en ? mask : (BIT(0) << spi_get_chipselect(spi, 0));
cs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG) & ~mask;
loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG, val | cs);
(Renamed variables to be consistent with the other uses in the driver below)
> +}
> +
> +static void loongson_spi_set_clk(struct loongson_spi *loongson_spi, unsigned int hz)
> +{
> + unsigned char val;
> + unsigned int div, div_tmp;
> + static const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
> +
> + div = clamp_val(DIV_ROUND_UP_ULL(loongson_spi->clk_rate, hz), 2, 4096);
> + div_tmp = rdiv[fls(div - 1)];
> + loongson_spi->spcr = (div_tmp & GENMASK(1, 0)) >> 0;
> + loongson_spi->sper = (div_tmp & GENMASK(3, 2)) >> 2;
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
val &= GENMASK(1, 0);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, (val & ~3) |
> + loongson_spi->spcr);
loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, val
| loongson_spi->spcr);
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
val &= GENMASK(1, 0);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, (val & ~3) |
> + loongson_spi->sper);
loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, val
| loongson_spi->sper);
> + loongson_spi->hz = hz;
> +}
> +
> +static void loongson_spi_set_mode(struct loongson_spi *loongson_spi,
> + struct spi_device *spi)
> +{
> + unsigned char val;
> +
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
> + val &= ~(LOONGSON_SPI_SPCR_CPOL | LOONGSON_SPI_SPCR_CPHA);
> + if (spi->mode & SPI_CPOL)
> + val |= LOONGSON_SPI_SPCR_CPOL;
> + if (spi->mode & SPI_CPHA)
> + val |= LOONGSON_SPI_SPCR_CPHA;
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, val);
> + loongson_spi->mode |= spi->mode;
> +}
> +
> +static int loongson_spi_update_state(struct loongson_spi *loongson_spi,
> + struct spi_device *spi, struct spi_transfer *t)
> +{
> + if (t && loongson_spi->hz != t->speed_hz)
> + loongson_spi_set_clk(loongson_spi, t->speed_hz);
> +
> + if ((spi->mode ^ loongson_spi->mode) & SPI_MODE_X_MASK)
> + loongson_spi_set_mode(loongson_spi, spi);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_setup(struct spi_device *spi)
> +{
> + struct loongson_spi *loongson_spi;
> +
> + loongson_spi = spi_controller_get_devdata(spi->controller);
> + if (spi->bits_per_word % 8)
> + return -EINVAL;
> +
> + if (spi_get_chipselect(spi, 0) >= spi->controller->num_chipselect)
> + return -EINVAL;
> +
> + loongson_spi->hz = 0;
> + loongson_spi_set_cs(spi, 1);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_write_read_8bit(struct spi_device *spi, const u8 **tx_buf,
> + u8 **rx_buf, unsigned int num)
> +{
> + int ret;
> + struct loongson_spi *loongson_spi = spi_controller_get_devdata(spi->controller);
> +
> + if (tx_buf && *tx_buf)
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG, *((*tx_buf)++));
> + else
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG, 0);
+ Blank line
> + ret = readb_poll_timeout(loongson_spi->base + LOONGSON_SPI_SPSR_REG, loongson_spi->spsr,
> + (loongson_spi->spsr & 0x1) != LOONGSON_SPI_SPSR_RFEMPTY, 1, MSEC_PER_SEC);
(loongson_spi->spsr &
LOONGSON_SPI_SPSR_RFEMPTY) != LOONGSON_SPI_SPSR_RFEMPTY,
1, MSEC_PER_SEC);
> + if (rx_buf && *rx_buf)
> + *(*rx_buf)++ = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_FIFO_REG);
> + else
> + loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_FIFO_REG);
> +
> + return ret;
> +}
> +
> +static int loongson_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
> +{
> + int ret;
> + unsigned int count;
> + const u8 *tx = xfer->tx_buf;
> + u8 *rx = xfer->rx_buf;
> +
> + count = xfer->len;
> +
Unneeded blank line.
> + do {
> + ret = loongson_spi_write_read_8bit(spi, &tx, &rx, count);
> + if (ret)
> + break;
> + } while (--count);
> +
> + return ret;
> +}
> +
> +static int loongson_spi_prepare_message(struct spi_controller *ctlr, struct spi_message *m)
> +{
> + struct loongson_spi *loongson_spi = spi_controller_get_devdata(ctlr);
> + loongson_spi->para = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_PARA_REG);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para & ~1);
BIT(0) ?
LOONGSON_SPI_PARA_MEM_EN ?
> + return 0;
> +}
> +
> +static int loongson_spi_transfer_one(struct spi_controller *ctrl, struct spi_device *spi,
> + struct spi_transfer *xfer)
> +{
> + struct loongson_spi *loongson_spi = spi_controller_get_devdata(spi->controller);
> +
> + loongson_spi_update_state(loongson_spi, spi, xfer);
> + if (xfer->len)
> + return loongson_spi_write_read(spi, xfer);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_unprepare_message(struct spi_controller *ctrl, struct spi_message *m)
> +{
> + struct loongson_spi *loongson_spi = spi_controller_get_devdata(ctrl);
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para);
> +
> + return 0;
> +}
> +
> +static void loongson_spi_reginit(struct loongson_spi *loongson_spi_dev)
> +{
> + unsigned char val;
> +
> + val = loongson_spi_read_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG);
> + val &= ~LOONGSON_SPI_SPCR_SPE;
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG, val);
> +
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPSR_REG,
> + (LOONGSON_SPI_SPSR_SPIF | LOONGSON_SPI_SPSR_WCOL));
> +
> + val = loongson_spi_read_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG);
> + val |= LOONGSON_SPI_SPCR_SPE;
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG, val);
> +}
> +
> +int loongson_spi_init_controller(struct device *dev, void __iomem *regs)
> +{
> + struct spi_controller *controller;
> + struct loongson_spi *spi;
> + struct clk *clk;
> +
> + controller = devm_spi_alloc_host(dev, sizeof(struct loongson_spi));
> + if (controller == NULL)
> + return -ENOMEM;
> +
> + controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
... = SPI_MODE_X_MASK | SPI_CS_HIGH;
> + controller->setup = loongson_spi_setup;
> + controller->prepare_message = loongson_spi_prepare_message;
> + controller->transfer_one = loongson_spi_transfer_one;
> + controller->unprepare_message = loongson_spi_unprepare_message;
> + controller->set_cs = loongson_spi_set_cs;
> + controller->num_chipselect = 4;
> + device_set_node(&controller->dev, dev_fwnode(dev));
> + dev_set_drvdata(dev, controller);
> +
> + spi = spi_controller_get_devdata(controller);
> + spi->base = regs;
> + spi->controller = controller;
> +
> + clk = devm_clk_get_optional(dev, NULL);
> + if (IS_ERR(clk))
> + return dev_err_probe(dev, PTR_ERR(clk), "unable to get clock\n");
> +
> + spi->clk_rate = clk_get_rate(clk);
> + loongson_spi_reginit(spi);
> +
> + spi->mode = 0;
> +
> + return devm_spi_register_controller(dev, controller);
> +}
> +EXPORT_SYMBOL_NS_GPL(loongson_spi_init_controller, SPI_LOONGSON_CORE);
> +
> +static int __maybe_unused loongson_spi_suspend(struct device *dev)
> +{
> + struct loongson_spi *loongson_spi;
> + struct spi_controller *controller;
> +
> + controller = dev_get_drvdata(dev);
> + spi_controller_suspend(controller);
> +
> + loongson_spi = spi_controller_get_devdata(controller);
> +
> + loongson_spi->spcr = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
> + loongson_spi->sper = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
> + loongson_spi->spsr = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPSR_REG);
> + loongson_spi->para = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_PARA_REG);
> + loongson_spi->sfcs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG);
> + loongson_spi->timi = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_TIMI_REG);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused loongson_spi_resume(struct device *dev)
> +{
> + struct loongson_spi *loongson_spi;
> + struct spi_controller *controller;
> +
> + controller = dev_get_drvdata(dev);
> + loongson_spi = spi_controller_get_devdata(controller);
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, loongson_spi->spcr);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, loongson_spi->sper);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPSR_REG, loongson_spi->spsr);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG, loongson_spi->sfcs);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_TIMI_REG, loongson_spi->timi);
> +
> + spi_controller_resume(controller);
> +
> + return 0;
> +}
> +
> +const struct dev_pm_ops loongson_spi_dev_pm_ops = {
> + .suspend = loongson_spi_suspend,
> + .resume = loongson_spi_resume,
> +};
> +EXPORT_SYMBOL_NS_GPL(loongson_spi_dev_pm_ops, SPI_LOONGSON_CORE);
> +
> +MODULE_DESCRIPTION("Loongson SPI core driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/spi/spi-loongson-pci.c b/drivers/spi/spi-loongson-pci.c
> new file mode 100644
> index 000000000000..134cda0c13a5
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-pci.c
> @@ -0,0 +1,55 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// PCI interface driver for Loongson SPI Support
> +// Copyright (C) 2023 Loongson Technology Corporation Limited
> +
> +#include <linux/mod_devicetable.h>
> +#include <linux/pci.h>
> +
> +#include "spi-loongson.h"
> +
> +static int loongson_spi_pci_register(struct pci_dev *pdev,
> + const struct pci_device_id *ent)
> +{
> + int ret;
> + void __iomem *reg_base;
> + struct device *dev = &pdev->dev;
> + int pci_bar = 0;
> +
> + ret = pcim_enable_device(pdev);
> + if (ret < 0)
> + return dev_err_probe(dev, ret, "cannot enable pci device\n");
> +
> + ret = pcim_iomap_regions(pdev, BIT(pci_bar), pci_name(pdev));
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to request and remap memory\n");
> +
> + reg_base = pcim_iomap_table(pdev)[pci_bar];
> +
> + ret = loongson_spi_init_controller(dev, reg_base);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to initialize controller\n");
> +
> + return 0;
> +}
> +
> +static struct pci_device_id loongson_spi_devices[] = {
> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a1b) },
> + { }
> +};
> +MODULE_DEVICE_TABLE(pci, loongson_spi_devices);
> +
> +static struct pci_driver loongson_spi_pci_driver = {
> + .name = "loongson-spi-pci",
> + .id_table = loongson_spi_devices,
> + .probe = loongson_spi_pci_register,
> + .driver = {
> + .bus = &pci_bus_type,
> + .pm = &loongson_spi_dev_pm_ops,
> + },
> +};
> +module_pci_driver(loongson_spi_pci_driver);
> +
> +MODULE_DESCRIPTION("Loongson spi pci driver");
> +MODULE_LICENSE("GPL");
> +MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
> diff --git a/drivers/spi/spi-loongson-plat.c b/drivers/spi/spi-loongson-plat.c
> new file mode 100644
> index 000000000000..c066e5f5891e
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-plat.c
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Platform driver for Loongson SPI Support
> +// Copyright (C) 2023 Loongson Technology Corporation Limited
> +
> +#include <linux/err.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/platform_device.h>
> +
> +#include "spi-loongson.h"
> +
> +static int loongson_spi_platform_probe(struct platform_device *pdev)
> +{
> + int ret;
> + void __iomem *reg_base;
> + struct device *dev = &pdev->dev;
> +
> + reg_base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(reg_base))
> + return PTR_ERR(reg_base);
> +
> + ret = loongson_spi_init_controller(dev, reg_base);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to initialize controller\n");
> +
> + return 0;
> +}
> +
> +static const struct of_device_id loongson_spi_id_table[] = {
> + { .compatible = "loongson,ls2k1000-spi" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, loongson_spi_id_table);
> +
> +static struct platform_driver loongson_spi_plat_driver = {
> + .probe = loongson_spi_platform_probe,
> + .driver = {
> + .name = "loongson-spi",
> + .bus = &platform_bus_type,
> + .pm = &loongson_spi_dev_pm_ops,
> + .of_match_table = loongson_spi_id_table,
> + },
> +};
> +module_platform_driver(loongson_spi_plat_driver);
> +
> +MODULE_DESCRIPTION("Loongson spi platform driver");
> +MODULE_LICENSE("GPL");
> +MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
> diff --git a/drivers/spi/spi-loongson.h b/drivers/spi/spi-loongson.h
> new file mode 100644
> index 000000000000..35f95b161842
> --- /dev/null
> +++ b/drivers/spi/spi-loongson.h
> @@ -0,0 +1,49 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/* Header File for Loongson SPI Driver. */
> +/* Copyright (C) 2023 Loongson Technology Corporation Limited */
> +
> +#ifndef __LINUX_SPI_LOONGSON_H
> +#define __LINUX_SPI_LOONGSON_H
> +
> +#include <linux/bits.h>
> +#include <linux/pm.h>
> +#include <linux/types.h>
> +
> +#define LOONGSON_SPI_SPCR_REG 0x00
> +#define LOONGSON_SPI_SPSR_REG 0x01
> +#define LOONGSON_SPI_FIFO_REG 0x02
> +#define LOONGSON_SPI_SPER_REG 0x03
> +#define LOONGSON_SPI_PARA_REG 0x04
> +#define LOONGSON_SPI_SFCS_REG 0x05
> +#define LOONGSON_SPI_TIMI_REG 0x06
> +
> +/* Bits definition for Loongson SPI register */
> +#define LOONGSON_SPI_PARA_MEM_EN BIT(0)
> +#define LOONGSON_SPI_SPCR_CPHA BIT(2)
> +#define LOONGSON_SPI_SPCR_CPOL BIT(3)
> +#define LOONGSON_SPI_SPCR_SPE BIT(6)
> +#define LOONGSON_SPI_SPSR_RFEMPTY BIT(0)
> +#define LOONGSON_SPI_SPSR_WCOL BIT(6)
> +#define LOONGSON_SPI_SPSR_SPIF BIT(7)
> +
> +struct device;
> +struct spi_controller;
> +
> +struct loongson_spi {
> + struct spi_controller *controller;
> + void __iomem *base;
> + int cs_active;
> + unsigned int hz;
> + unsigned char spcr;
> + unsigned char sper;
> + unsigned char spsr;
> + unsigned char para;
> + unsigned char sfcs;
> + unsigned char timi;
> + unsigned int mode;
> + u64 clk_rate;
> +};
> +
> +int loongson_spi_init_controller(struct device *dev, void __iomem *reg);
> +extern const struct dev_pm_ops loongson_spi_dev_pm_ops;
> +#endif /* __LINUX_SPI_LOONGSON_H */
> --
> 2.20.1
>
--
With Best Regards,
Andy Shevchenko
