Re: [PATCH RFC 03/10] drm/panel: Add LGD panel driver for Sony Xperia XZ3

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 30 May 2023 at 11:27, Marijn Suijten
<marijn.suijten@xxxxxxxxxxxxxx> wrote:
>
> On 2023-05-30 01:39:10, Dmitry Baryshkov wrote:
> > On 30/05/2023 01:37, Marijn Suijten wrote:
> > > On 2023-05-30 01:18:40, Dmitry Baryshkov wrote:
> > > <snip>
> > >>>>>>> +    ret = mipi_dsi_dcs_set_display_on(dsi);
> > >>>>>>> +    if (ret < 0) {
> > >>>>>>> +        dev_err(dev, "Failed to turn display on: %d\n", ret);
> > >>>>>>> +        return ret;
> > >>>>>>> +    }
> > >>>>>>
> > >>>>>> My usual question: should the mipi_dsi_dcs_exit_sleep_mode() / mipi_dsi_dcs_set_display_on() be moved from prepare() to enable() part?
> > >>>>>
> > >>>>>
> > >>>>> No, prepare is called before the video stream is started and when display is still in LPM mode and the mode hasn't been set.
> > >>>>>
> > >>>>
> > >>>> Yes, that's my point. Shouldn't we enable the panel _after_ starting the stream?
> > >>>
> > >>> I have never investigated what it takes to split these functions, but
> > >>> some of these panels do show some corruption at startup which may be
> > >>> circumvented by powering the panel on after starting the video stream?
> > >>>
> > >>> I'm just not sure where to make the split: downstream does describe a
> > >>> qcom,mdss-dsi-on-command and qcom,mdss-dsi-post-panel-on-command, where
> > >>> the latter only contains set_display_on() (not exit_sleep_mode()).
> > >>> It is documented like:
> > >>>
> > >>>       same as "qcom,mdss-dsi-on-command" except commands are sent after
> > >>>       displaying an image."
> > >>>
> > >>> So this seems like the right way to split them up, I'll test this out on
> > >>> all submitted panel drivers.
> > >>
> > >> Interesting enough, Neil suggested that sending all the commands during
> > >> pre_enable() is the correct sequence (especially for VIDEO mode panels),
> > >> since not all DSI hosts can send commands after switching to the VIDEO mode.
> > >
> > > Note that all these panels and Driver-ICs are command-mode, and/or
> > > programmed to run in command-mode, so there shouldn't be any notion of a
> > > VIDEO stream (any command-mode frame is just an "arbitrary command" as
> > > far as I understood).
> >
> > Yes, from the data stream point of view. I was talking about the DSI
> > host being able to send arbitrary commands or not after enabling the
> > video/cmd stream.
>
> Is this a known limitation of SM8250 then?  Or is the brightness_set
> issue more likely a "problem" with the panel that the downstream kernel
> is "somehow" working around or aware of, and I just haven't found
> how/where it deals with that?
> (Alternatively we could be "doing it wrong" for other panels but it
>  turns out to be working anyway)

Please excuse me for not being explicit enough. Qualcomm hardware
doesn't have this problem. Thus I was completely unaware of it before
talking to Neil.
So, our hardware works in most of the cases.

-- 
With best wishes
Dmitry



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux