[PATCH 6/6] arm64: dts: rockchip: Add Indiedroid Nova board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Chris Morgan <macromorgan@xxxxxxxxxxx>

The Indiedroid Nova is an SBC from a sub-brand of Ameridroid that
includes the following hardware:

 - A 40-pin GPIO header
 - 2 USB-A 3.0 ports
 - 2 USB-A 2.0 ports
 - A USB-C 2.0 OTG port (used for USB power delivery)
 - A USB-C 3.0 port that can do display port output.
 - A Micro HDMI 2.1 port.
 - A 1GB ethernet port.
 - An RT8821CS based WiFi/Bluetooth module.
 - A user replaceable eMMC module.
 - An SDMMC card slot.
 - A MIPI DSI connector.
 - A MIPI CSI connector.
 - A 3.5mm TRRS audio jack with microphone input.
 - An 2 pin socket for an RTC battery.
 - A 4 pin socket for a debug port.
 - A power button (connected to PMIC), a reset button (connected to SoC
   reset), a boot button, and a recovery button (both connected to the
   ADC).
 - 4GB, 8GB, or 16GB of system RAM.

This initial devicetree includes support for the WiFi, bluetooth,
analog audio out/in, SDMMC, eMMC, RTC, UART debugging, and has
the regulator values from the schematics. ADC, graphics output, GPU,
USB, and wired ethernet are still pending additional upstream changes.

Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3588s-indiedroid-nova.dts  | 761 ++++++++++++++++++
 2 files changed, 762 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 2d585bbb8f3a..99f11db8158d 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -94,5 +94,6 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts
new file mode 100644
index 000000000000..b7070dd970e6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts
@@ -0,0 +1,761 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3588s.dtsi"
+
+/ {
+	model = "Indiedroid Nova";
+	compatible = "indiedroid,nova", "rockchip,rk3588s";
+
+	aliases {
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+		mmc2 = &sdio;
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clock-names = "ext_clock";
+		clocks = <&rtc_hym8563>;
+		pinctrl-0 = <&wifi_enable_h>;
+		pinctrl-names = "default";
+		post-power-on-delay-ms = <200>;
+		reset-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "rockchip,es8388-codec";
+		widgets = "Microphone", "Mic Jack",
+			  "Headphone", "Headphones";
+		routing = "LINPUT2", "Mic Jack",
+			  "Headphones", "LOUT1",
+			  "Headphones", "ROUT1";
+		dais = <&i2s0_8ch_p0>;
+	};
+
+	vbus5v0_typec: vbus5v0-typec {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&typec5v_pwren>;
+		pinctrl-names = "default";
+		regulator-name = "vbus5v0_typec";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc_1v1_nldo_s3: vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1100000>;
+		regulator-min-microvolt = <1100000>;
+		regulator-name = "vcc_1v1_nldo_s3";
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* Regulator is enabled whenever vcc_1v8_s0 is above 1.6v */
+	vcc_3v3_s0: vcc-3v3-s0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "vcc_3v3_s0";
+		vin-supply = <&vcc_3v3_s3>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "vcc5v0_sys";
+	};
+
+	vcc5v0_usb: vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "vcc5v0_usb";
+		vin-supply = <&vcc5v0_usbdcin>;
+	};
+
+	vcc5v0_usbdcin: vcc5v0-usbdcin {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "vcc5v0_usbdcin";
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_b0{
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1{
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2{
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3{
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+/*
+ * Add labels for each GPIO pin exposed on the 40 pin header. Note that
+ * voltage of each GPIO pin could be either 3.3v or 1.8v (as noted by
+ * label).
+ */
+&gpio0 {
+	gpio-line-names = /* GPIO0 A0-A7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO0 B0-B7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO0 C0-C7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO0 D0-D7 */
+			  "HEADER_12_1v8", "", "", "HEADER_24_1v8",
+			  "", "", "", "";
+};
+
+&gpio1 {
+	gpio-line-names = /* GPIO1 A0-A7 */
+			  "HEADER_27_3v3", "HEADER_28_3v3", "", "",
+			  "HEADER_29_1v8", "", "HEADER_7_1v8", "",
+			  /* GPIO1 B0-B7 */
+			  "", "HEADER_31_1v8", "HEADER_33_1v8", "",
+			  "HEADER_11_1v8", "HEADER_13_1v8", "", "",
+			  /* GPIO1 C0-C7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO1 D0-D7 */
+			  "", "", "", "",
+			  "", "", "HEADER_5_3v3", "HEADER_3_3v3";
+};
+
+&gpio3 {
+	gpio-line-names = /* GPIO3 A0-A7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO3 B0-B7 */
+			  "HEADER_16_1v8", "HEADER_18_1v8", "", "",
+			  "", "", "", "HEADER_19_1v8",
+			  /* GPIO3 C0-C7 */
+			  "HEADER_21_1v8", "HEADER_23_1v8", "", "HEADER_26_1v8",
+			  "HEADER_15_1v8", "HEADER_22_1v8", "", "",
+			  /* GPIO3 D0-D7 */
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = /* GPIO4 A0-A7 */
+			  "", "", "HEADER_37_3v3", "HEADER_32_3v3",
+			  "HEADER_36_3v3", "", "HEADER_35_3v3", "HEADER_38_3v3",
+			  /* GPIO4 B0-B7 */
+			  "", "", "", "HEADER_40_3v3",
+			  "HEADER_8_3v3", "HEADER_10_3v3", "", "",
+			  /* GPIO4 C0-C7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO4 D0-D7 */
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0m2_xfer>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1050000>;
+		regulator-min-microvolt = <550000>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-ramp-delay = <2300>;
+		fcs,suspend-voltage-selector = <1>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1050000>;
+		regulator-min-microvolt = <550000>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-ramp-delay = <2300>;
+		fcs,suspend-voltage-selector = <1>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <950000>;
+		regulator-min-microvolt = <550000>;
+		regulator-name = "vdd_npu_s0";
+		regulator-ramp-delay = <2300>;
+		fcs,suspend-voltage-selector = <1>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c6 {
+	pinctrl-0 = <&i2c6m3_xfer>;
+	status = "okay";
+
+	fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PC4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&usbc0_int>;
+		pinctrl-names = "default";
+		vbus-supply = <&vbus5v0_typec>;
+
+		connector {
+			compatible = "usb-c-connector";
+			data-role = "dual";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+			op-sink-microwatt = <1000000>;
+		};
+	};
+
+	rtc_hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&hym8563_int>;
+		pinctrl-names = "default";
+		wakeup-source;
+	};
+};
+
+&i2c7 {
+	pinctrl-0 = <&i2c7m0_xfer>;
+	status = "okay";
+
+	es8388: audio-codec@11 {
+		compatible = "everest,es8388";
+		reg = <0x11>;
+		AVDD-supply = <&vcc_3v3_s3>;
+		clock-names = "mclk";
+		clocks = <&cru I2S0_8CH_MCLKOUT>;
+		DVDD-supply = <&vcc_1v8_s3>;
+		HPVDD-supply = <&vcc_3v3_s3>;
+		PVDD-supply = <&vcc_1v8_s3>;
+		#sound-dai-cells = <0>;
+
+		port {
+			es8388_p0_0: endpoint {
+				remote-endpoint = <&i2s0_8ch_p0_0>;
+			};
+		};
+	};
+};
+
+&i2s0_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_lrck
+		     &i2s0_mclk
+		     &i2s0_sclk
+		     &i2s0_sdi0
+		     &i2s0_sdo0>;
+	status = "okay";
+
+	i2s0_8ch_p0: port {
+		i2s0_8ch_p0_0: endpoint {
+			dai-format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&es8388_p0_0>;
+		};
+	};
+};
+
+
+&pinctrl {
+	bluetooth-pins {
+		bt_reset: bt-reset {
+			rockchip,pins =
+				<0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_dev: bt-wake-dev {
+			rockchip,pins =
+				<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins =
+				<0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	hym8563 {
+
+		hym8563_int: hym8563-int {
+			rockchip,pins =
+				<0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins =
+				<0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb-typec {
+		usbc0_int: usbc0-int {
+			rockchip,pins =
+				<0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		typec5v_pwren: typec5v-pwren {
+			rockchip,pins =
+				<4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+/* HS400 modes seemed to cause io errors. */
+&sdhci {
+	bus-width = <8>;
+	no-mmc-hs400;
+	no-sd;
+	no-sdio;
+	non-removable;
+	max-frequency = <200000000>;
+	vmmc-supply = <&vcc_3v3_s0>;
+	vqmmc-supply = <&vcc_1v8_s3>;
+	status = "okay";
+};
+
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	disable-wp;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	no-mmc;
+	no-sd;
+	non-removable;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vcc_1v8_s3>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <200000000>;
+	no-sdio;
+	no-mmc;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&spi2 {
+	#address-cells = <1>;
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-0 = <&spi2m2_pins>, <&spi2m2_cs0>;
+	pinctrl-names = "default";
+	#size-cells = <0>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: dcdc-reg1 {
+				regulator-boot-on;
+				regulator-enable-ramp-delay = <400>;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <550000>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-ramp-delay = <12500>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <550000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_logic_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <750000>;
+				regulator-min-microvolt = <675000>;
+				regulator-name = "vdd_logic_s0";
+				regulator-ramp-delay = <12500>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <550000>;
+				regulator-name = "vdd_vdenc_s0";
+				regulator-ramp-delay = <12500>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <850000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "vdd2_ddr_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2000000>;
+				regulator-min-microvolt = <2000000>;
+				regulator-name = "vdd_2v0_pldo_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <600000>;
+				regulator-min-microvolt = <600000>;
+				regulator-name = "vddq_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcca_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-name = "vdda_1v2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vcca_3v3_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vccio_sd_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3_pldo6: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3_pldo6";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <750000>;
+				regulator-min-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <850000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			avdd_0v75_s0: nldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <750000>;
+				regulator-min-microvolt = <750000>;
+				regulator-name = "avdd_0v75_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_0v85_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* Schematics show not in use */
+			nldo-reg5 {
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2m0_xfer>;
+	status = "okay";
+};
+
+/* DMA seems to interfere with bluetooth device normal operation. */
+&uart9 {
+	pinctrl-0 = <&uart9m2_xfer>, <&uart9m2_ctsn>, <&uart9m2_rtsn>;
+	pinctrl-names = "default";
+	/delete-property/ dma-names;
+	/delete-property/ dmas;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8821cs-bt",
+			     "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&bt_reset>, <&bt_wake_dev>, <&bt_wake_host>;
+		pinctrl-names = "default";
+	};
+};
-- 
2.34.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux