In this change we add support to the generic PHY framework.
Two UFS phys are implemented:
qmp-20nm and qmp-28nm.
Also, the files in this change implement the UFS HW (controller & PHY)
specific behavior in Qualcomm chips.
Relocation of a few header files is needed in order to expose routines
and data structures between PHY driver and UFS driver.
Also, this change include the implementation of Inline Crypto Engine (ICE)
in Qualcomm chips.
Signed-off-by: Yaniv Gardi <ygardi@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/ufs/ufs-msm.txt | 49 +
.../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 113 +-
drivers/phy/Makefile | 3 +
drivers/phy/phy-qcom-ufs-qmp-20nm.c | 266 +++++
drivers/phy/phy-qcom-ufs-qmp-20nm.h | 232 ++++
drivers/phy/phy-qcom-ufs-qmp-28nm.c | 331 ++++++
drivers/phy/phy-qcom-ufs-qmp-28nm.h | 738 ++++++++++++
drivers/phy/phy-qcom-ufs.c | 777 +++++++++++++
drivers/scsi/ufs/Kconfig | 24 +
drivers/scsi/ufs/Makefile | 2 +
drivers/scsi/ufs/ufs-qcom-ice.c | 522 +++++++++
drivers/scsi/ufs/ufs-qcom-ice.h | 113 ++
drivers/scsi/ufs/ufs-qcom.c | 1204 ++++++++++++++++++++
drivers/scsi/ufs/ufs.h | 491 --------
drivers/scsi/ufs/ufshcd-pci.c | 2 +-
drivers/scsi/ufs/ufshcd-pltfrm.c | 2 +-
drivers/scsi/ufs/ufshcd.c | 97 +-
drivers/scsi/ufs/ufshcd.h | 596 ----------
drivers/scsi/ufs/unipro.h | 207 ----
include/linux/phy/phy-qcom-ufs.h | 205 ++++
include/linux/scsi/ufs/ufs-qcom.h | 210 ++++
include/linux/scsi/ufs/ufs.h | 491 ++++++++
include/linux/scsi/ufs/ufshcd.h | 654 +++++++++++
include/linux/scsi/ufs/unipro.h | 207 ++++
24 files changed, 6232 insertions(+), 1304 deletions(-)
create mode 100644 Documentation/devicetree/bindings/ufs/ufs-msm.txt
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.c
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.h
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-28nm.c
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-28nm.h
create mode 100644 drivers/phy/phy-qcom-ufs.c
create mode 100644 drivers/scsi/ufs/ufs-qcom-ice.c
create mode 100644 drivers/scsi/ufs/ufs-qcom-ice.h
create mode 100644 drivers/scsi/ufs/ufs-qcom.c
delete mode 100644 drivers/scsi/ufs/ufs.h
delete mode 100644 drivers/scsi/ufs/ufshcd.h
delete mode 100644 drivers/scsi/ufs/unipro.h
create mode 100644 include/linux/phy/phy-qcom-ufs.h
create mode 100644 include/linux/scsi/ufs/ufs-qcom.h
create mode 100644 include/linux/scsi/ufs/ufs.h
create mode 100644 include/linux/scsi/ufs/ufshcd.h
create mode 100644 include/linux/scsi/ufs/unipro.h
diff --git a/Documentation/devicetree/bindings/ufs/ufs-msm.txt b/Documentation/devicetree/bindings/ufs/ufs-msm.txt
new file mode 100644
index 0000000..a9bf139
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-msm.txt
@@ -0,0 +1,49 @@
+* MSM Universal Flash Storage (UFS) PHY
+
+UFSPHY nodes are defined to describe on-chip UFS PHY hardware macro.
+Each UFS PHY node should have its own node.
+
+To bind UFS PHY with UFS host controller, the controller node should
+contain a phandle reference to UFS PHY node.
+
+Required properties:
+- compatible : compatible list, contains "qcom,ufs-phy-qmp-28nm",
+ "qcom,ufs-phy-qmp-20nm" or "qcom,ufs-phy-qmp-14nm"
+ according to the relevant phy in use
+- reg : should contain PHY register address space (mandatory),
+ device PHY control register map (optional).
+- reg-names : indicates various resources passed to driver (via reg proptery) by name.
+ Required "reg-names" is "phy_mem" and "dev_ref_clk_ctrl_mem" is optional.
+- #phy-cells : This property shall be set to 0
+- vdda-phy-supply : phandle to main PHY supply for analog domain
+- vdda-pll-supply : phandle to PHY PLL and Power-Gen block power supply
+- clocks : List of phandle and clock specifier pairs
+- clock-names : List of clock input name strings sorted in the same
+ order as the clocks property. "ref_clk_src", "ref_clk",
+ "tx_iface_clk" & "rx_iface_clk" are mandatory but
+ "ref_clk_parent" is optional
+
+Optional properties:
+- vdda-phy-max-microamp : specifies max. load that can be drawn from phy supply
+- vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply
+- vddp-ref-clk-supply : phandle to UFS device ref_clk pad power supply
+- vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply
+- vddp-ref-clk-always-on : specifies if this supply needs to be kept always on
+
+Example:
+
+ ufsphy1: ufsphy@0xfc597000 {
+ compatible = "qcom,ufs-phy-qmp-28nm";
+ reg = <0xfc597000 0x800>, <0xfd512074 0x4>;
+ reg-names = "phy_mem", "dev_ref_clk_ctrl_mem";
+ #phy-cells = <0>;
+ vdda-phy-supply = <&pma8084_l4>;
+ vdda-pll-supply = <&pma8084_l12>;
+ vdda-phy-max-microamp = <50000>;
+ vdda-pll-max-microamp = <1000>;
+ };
+
+ ufshc@0xfc598000 {
+ ...
+ phys = <&ufsphy1>;
+ };
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
index 5357919..3512616 100644
--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
@@ -4,11 +4,14 @@ UFSHC nodes are defined to describe on-chip UFS host controllers.
Each UFS controller instance should have its own node.
Required properties:
-- compatible : compatible list, contains "jedec,ufs-1.1"
+- compatible : compatible list, contains "jedec,ufs-1.1", "qcom,ufshc"
- interrupts : <interrupt mapping for UFS host controller IRQ>
- reg : <registers mapping>
Optional properties:
+- phys : phandle to UFS PHY node
+- phy-names : the string "ufsphy" when is found in a node, along
+ with "phys" attribute, provides phandle to UFS PHY node
- vdd-hba-supply : phandle to UFS host controller supply regulator node
- vcc-supply : phandle to VCC supply regulator node
- vccq-supply : phandle to VCCQ supply regulator node
@@ -31,6 +34,15 @@ Optional properties:
defined or a value in the array is "0" then it is assumed
that the frequency is set by the parent clock or a
fixed rate clock source.
+- rpm-level : UFS Runtime power management level. Following PM levels are suppported:
+ 0 - Both UFS device and Link in active state (Highest power consumption)
+ 1 - UFS device in active state but Link in Hibern8 state
+ 2 - UFS device in Sleep state but Link in active state
+ 3 - UFS device in Sleep state and Link in hibern8 state (default PM level)
+ 4 - UFS device in Power-down state and Link in Hibern8 state
+ 5 - UFS device in Power-down state and Link in OFF state (Lowest power consumption)
+- spm-level : UFS System power management level. Allowed PM levels are same as rpm-level.
+- ufs-qcom-crypto : phandle to UFS-QCOM ICE (Inline Cryptographic Engine) node
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
@@ -41,6 +53,8 @@ Example:
reg = <0xfc598000 0x800>;
interrupts = <0 28 0>;
+ ufs-phy = <&ufsphy>;
+ ufs-qcom-crypto = <&ufs_ice>;
vdd-hba-supply = <&xxx_reg0>;
vdd-hba-fixed-regulator;
vcc-supply = <&xxx_reg1>;
@@ -54,4 +68,101 @@ Example:
clocks = <&core 0>, <&ref 0>, <&iface 0>;
clock-names = "core_clk", "ref_clk", "iface_clk";
freq-table-hz = <100000000 200000000>, <0 0>, <0 0>;
+ rpm-level = <3>;
+ spm-level = <5>;
+ };
+
+==== MSM UFS platform driver properties =====
+* For UFS host controller in MSM platform following clocks are required -
+ Controller clock source -
+ "core_clk_src", max-clock-frequency-hz = 200MHz
+
+ Controller System clock branch:
+ "core_clk" - Controller core clock
+
+ AHB/AXI interface clocks:
+ "iface_clk" - AHB interface clock
+ "bus_clk" - AXI bus master clock
+
+ PHY to controller symbol synchronization clocks:
+ "rx_lane0_sync_clk" - RX Lane 0
+ "rx_lane1_sync_clk" - RX Lane 1
+ "tx_lane0_sync_clk" - TX Lane 0
+ "tx_lane1_sync_clk" - TX Lane 1
+
+ Optional reference clock input to UFS device
+ "ref_clk", max-clock-frequency-hz = 19.2MHz
+
+* Following bus parameters are required -
+- qcom,msm-bus,name
+- qcom,msm-bus,num-cases
+- qcom,msm-bus,num-paths
+- qcom,msm-bus,vectors-KBps
+For the above four properties please refer to
+Documentation/devicetree/bindings/arm/msm/msm_bus.txt
+Note: The instantaneous bandwidth (IB) value in the vectors-KBps field should
+ be zero as UFS data transfer path doesn't have latency requirements and
+ voting for aggregated bandwidth (AB) should take care of providing
+ optimum throughput requested.
+
+- qcom,bus-vector-names: specifies string IDs for the corresponding
+bus vectors in the same order as qcom,msm-bus,vectors-KBps property.
+
+- qcom,cpu-dma-latency-us: optional parameter specifying the allowed CPU-DMA
+ latency parameter for PM QOS, in units of microseconds. If this parameter is
+ not specified a default of 200us is used.
+- qcom,cpu-affinity: this is a string that specifies the pm QoS request type.
+ The supported cpu affinity modes are:
+ "all_cores" - PM_QOS_REQ_ALL_CORES is applicable to all CPU cores that are
+ online and this would have a power impact when there are more number of CPUs.
+ "affine_irq" - PM_QOS_REQ_AFFINE_IRQ request type shall update/apply the vote
+ only to that CPU to which this IRQ's affinity is set to.
+ "affine_cores" - PM_QOS_REQ_AFFINE_CORES request type is used for targets that
+ have little cluster and will update/apply the vote to all the cores in the
+ little cluster.
+ The default CPU affinity mode is PM_QOS_REQ_AFFINE_IRQ.
+
+Example:
+ ufshc@0xfc598000 {
+ ...
+
+ qcom,msm-bus,name = "ufs1";
+ qcom,msm-bus,num-cases = <22>;
+ qcom,msm-bus,num-paths = <2>;
+ qcom,msm-bus,vectors-KBps =
+ <95 512 0 0>, <1 650 0 0>, /* No vote */
+
+ <95 512 922 0>, <1 650 1000 0>, /* PWM G1 */
+ <95 512 1844 0>, <1 650 1000 0>, /* PWM G2 */
+ <95 512 3688 0>, <1 650 1000 0>, /* PWM G3 */
+ <95 512 7376 0>, <1 650 1000 0>, /* PWM G4 */
+ <95 512 1844 0>, <1 650 1000 0>, /* PWM G1 L2 */
+ <95 512 3688 0>, <1 650 1000 0>, /* PWM G2 L2 */
+ <95 512 7376 0>, <1 650 1000 0>, /* PWM G3 L2 */
+ <95 512 14752 0>, <1 650 1000 0>, /* PWM G4 L2 */
+
+ <95 512 127796 0>, <1 650 1000 0>, /* HS G1 RA */
+ <95 512 255591 0>, <1 650 1000 0>, /* HS G2 RA */
+ <95 512 511181 0>, <1 650 1000 0>, /* HS G3 RA */
+ <95 512 255591 0>, <1 650 1000 0>, /* HS G1 RA L2 */
+ <95 512 511181 0>, <1 650 1000 0>, /* HS G2 RA L2 */
+ <95 512 1022362 0>, <1 650 1000 0>, /* HS G3 RA L2 */
+
+ <95 512 149422 0>, <1 650 1000 0>, /* HS G1 RB */
+ <95 512 298189 0>, <1 650 1000 0>, /* HS G2 RB */
+ <95 512 596378 0>, <1 650 1000 0>, /* HS G3 RB */
+ <95 512 298189 0>, <1 650 1000 0>, /* HS G1 RB L2 */
+ <95 512 596378 0>, <1 650 1000 0>, /* HS G2 RB L2 */
+ <95 512 1192756 0>, <1 650 1000 0>, /* HS G3 RB L2 */
+
+ <95 512 4096000 0>, <1 650 1000 0>; /* Max. bandwidth */
+
+ qcom,bus-vector-names = "MIN",
+ "PWM_G1_L1", "PWM_G2_L1", "PWM_G3_L1", "PWM_G4_L1",
+ "PWM_G1_L2", "PWM_G2_L2", "PWM_G3_L2", "PWM_G4_L2",
+ "HS_RA_G1_L1", "HS_RA_G2_L1", "HS_RA_G3_L1",
+ "HS_RA_G1_L2", "HS_RA_G2_L2", "HS_RA_G3_L2",
+ "HS_RB_G1_L1", "HS_RB_G2_L1", "HS_RB_G3_L1",
+ "HS_RB_G1_L2", "HS_RB_G2_L2", "HS_RB_G3_L2",
+ "MAX";
};
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c4590fc..4fb782c 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -31,3 +31,6 @@ obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
+obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs.o
+obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs-qmp-28nm.o
+obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs-qmp-20nm.o
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/phy-qcom-ufs-qmp-20nm.c
new file mode 100644
index 0000000..31a3b54
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.c
@@ -0,0 +1,266 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <linux/phy/phy-qcom-ufs.h>
+#include "phy-qcom-ufs-qmp-20nm.h"
+
+#define UFS_PHY_NAME "ufs_phy_qmp_20nm"
+
+static
+int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy)
+{
+ struct ufs_qcom_phy_calibration *tbl_A, *tbl_B;
+ int tbl_size_A, tbl_size_B;
+ int rate = UFS_QCOM_LIMIT_HS_RATE;
+ u8 major = ufs_qcom_phy->host_ctrl_rev_major;
+ u16 minor = ufs_qcom_phy->host_ctrl_rev_minor;
+ u16 step = ufs_qcom_phy->host_ctrl_rev_step;
+ int err;
+
+ if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0);
+ tbl_A = phy_cal_table_rate_A_1_2_0;
+ } else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0);
+ tbl_A = phy_cal_table_rate_A_1_3_0;
+ } else {
+ dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n",
+ __func__);
+ err = -ENODEV;
+ goto out;
+ }
+
+ tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+ tbl_B = phy_cal_table_rate_B;
+
+ err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A,
+ tbl_B, tbl_size_B, rate);
+
+ if (err)
+ dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n",
+ __func__, err);
+
+out:
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+ phy_common->quirks =
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy_qmp_20nm *phy = phy_get_drvdata(generic_phy);
+ struct ufs_qcom_phy *phy_common = &phy->common_cfg;
+ int err = 0;
+
+ err = ufs_qcom_phy_init_clks(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common);
+
+out:
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+ bool hibern8_exit_after_pwr_collapse = phy->quirks &
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+
+ if (val) {
+ writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * Before any transactions involving PHY, ensure PHY knows
+ * that it's analog rail is powered ON.
+ */
+ mb();
+
+ if (hibern8_exit_after_pwr_collapse) {
+ /*
+ * Give atleast 1us delay after restoring PHY analog
+ * power.
+ */
+ usleep_range(1, 2);
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x08, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure workaround is deactivated before proceeding
+ * with normal PHY operations.
+ */
+ mb();
+ }
+ } else {
+ if (hibern8_exit_after_pwr_collapse) {
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x02, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure that above workaround is activated before
+ * PHY analog power collapse.
+ */
+ mb();
+ }
+
+ writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * ensure that PHY knows its PHY analog rail is going
+ * to be powered down
+ */
+ mb();
+ }
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+ writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK,
+ phy->mmio + UFS_PHY_TX_LANE_ENABLE);
+ mb();
+}
+
+static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+ u32 tmp;
+
+ tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+ tmp &= ~MASK_SERDES_START;
+ tmp |= (1 << OFFSET_SERDES_START);
+ writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+ mb();
+}
+
+static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+ int err = 0;
+ u32 val;
+
+ err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+ val, (val & MASK_PCS_READY), 10, 1000000);
+ if (err)
+ dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n",
+ __func__, err);
+ return err;
+}
+
+struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
+ .init = ufs_qcom_phy_qmp_20nm_init,
+ .exit = ufs_qcom_phy_exit,
+ .power_on = ufs_qcom_phy_power_on,
+ .power_off = ufs_qcom_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+struct ufs_qcom_phy_specific_ops phy_20nm_ops = {
+ .calibrate_phy = ufs_qcom_phy_qmp_20nm_phy_calibrate,
+ .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes,
+ .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready,
+ .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable,
+ .power_control = ufs_qcom_phy_qmp_20nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct ufs_qcom_phy_qmp_20nm *phy;
+ int err = 0;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ dev_err(dev, "%s: failed to allocate phy\n", __func__);
+ err = -ENOMEM;
+ goto out;
+ }
+
+ generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg,
+ &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops);
+
+ if (!generic_phy) {
+ dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n",
+ __func__);
+ err = -EIO;
+ goto out;
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+
+ strlcpy(phy->common_cfg.name, UFS_PHY_NAME,
+ sizeof(phy->common_cfg.name));
+
+out:
+ return err;
+}
+
+static int ufs_qcom_phy_qmp_20nm_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy = to_phy(dev);
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int err = 0;
+
+ err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy);
+ if (err)
+ dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n",
+ __func__, err);
+
+ return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = {
+ {.compatible = "qcom,ufs-phy-qmp-20nm"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = {
+ .probe = ufs_qcom_phy_qmp_20nm_probe,
+ .remove = ufs_qcom_phy_qmp_20nm_remove,
+ .driver = {
+ .of_match_table = ufs_qcom_phy_qmp_20nm_of_match,
+ .name = "ufs_qcom_phy_qmp_20nm",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_20nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/phy-qcom-ufs-qmp-20nm.h
new file mode 100644
index 0000000..895c259
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.h
@@ -0,0 +1,232 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_QMP_20NM_H_
+#define UFS_QCOM_PHY_QMP_20NM_H_
+
+#include <linux/phy/phy-qcom-ufs.h>
+
+/* QCOM UFS PHY control registers */
+
+#define COM_OFF(x) (0x000 + x)
+#define PHY_OFF(x) (0xC00 + x)
+#define TX_OFF(n, x) (0x400 + (0x400 * n) + x)
+#define RX_OFF(n, x) (0x600 + (0x400 * n) + x)
+
+/* UFS PHY PLL block registers */
+#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0)
+#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04)
+#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14)
+#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24)
+#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28)
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30)
+#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34)
+#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38)
+#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C)
+#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48)
+#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C)
+#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50)
+#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90)
+#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94)
+#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98)
+#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C)
+#define QSERDES_COM_BGTC COM_OFF(0xA0)
+#define QSERDES_COM_DEC_START1 COM_OFF(0xAC)
+#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0)
+#define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8)
+#define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC)
+#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100)
+#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104)
+#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108)
+#define QSERDES_COM_DEC_START2 COM_OFF(0x10C)
+#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110)
+#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114)
+#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118)
+
+/* TX LANE n (0, 1) registers */
+#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08)
+#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C)
+#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54)
+
+/* RX LANE n (0, 1) registers */
+#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0)
+#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8)
+#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8)
+#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC)
+#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0)
+#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4)
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC)
+#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC)
+#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100)
+
+/* UFS PHY registers */
+#define UFS_PHY_PHY_START PHY_OFF(0x00)
+#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4)
+#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44)
+#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08)
+#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C)
+#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10)
+#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14)
+#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34)
+#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38)
+#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C)
+#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40)
+#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68)
+#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28)
+#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C)
+#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48)
+#define UFS_PHY_PLL_CNTL PHY_OFF(0x50)
+#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54)
+#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C)
+#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58)
+#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60)
+#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64)
+#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C)
+#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4)
+#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0)
+#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8)
+#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4)
+#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC)
+#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8)
+#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC)
+#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100)
+#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6)
+#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5)
+#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2)
+#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1)
+#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0)
+#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164)
+#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168)
+#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C)
+#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170)
+#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174)
+
+#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3
+
+/*
+ * This structure represents the 20nm specific phy.
+ * common_cfg MUST remain the first field in this structure
+ * in case extra fields are added. This way, when calling
+ * get_ufs_qcom_phy() of generic phy, we can extract the
+ * common phy structure (struct ufs_qcom_phy) out of it
+ * regardless of the relevant specific phy.
+ */
+struct ufs_qcom_phy_qmp_20nm {
+ struct ufs_qcom_phy common_cfg;
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e),
+};
+
+#endif
diff --git a/drivers/phy/phy-qcom-ufs-qmp-28nm.c b/drivers/phy/phy-qcom-ufs-qmp-28nm.c
new file mode 100644
index 0000000..512b1c9
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-28nm.c
@@ -0,0 +1,331 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+#include <linux/phy/phy-qcom-ufs.h>
+#include "phy-qcom-ufs-qmp-28nm.h"
+
+#define UFS_PHY_NAME "ufs_qcom_phy_qmp_28nm"
+
+static
+void ufs_qcom_phy_qmp_28nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+ if (val) {
+ writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * Before any transactions involving PHY, ensure PHY knows
+ * that it's analog rail is powered ON. This also ensures
+ * that PHY is out of power collapse before enabling the
+ * SIGDET.
+ */
+ mb();
+ if (phy->quirks & UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE) {
+ writel_relaxed(0xC0,
+ phy->mmio + QSERDES_RX_SIGDET_CNTRL(0));
+ writel_relaxed(0xC0,
+ phy->mmio + QSERDES_RX_SIGDET_CNTRL(1));
+ /*
+ * make sure that SIGDET is enabled before proceeding
+ * further.
+ */
+ mb();
+ }
+ } else {
+ if (phy->quirks &
+ UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE) {
+ writel_relaxed(0x0,
+ phy->mmio + QSERDES_RX_SIGDET_CNTRL(0));
+ writel_relaxed(0x0,
+ phy->mmio + QSERDES_RX_SIGDET_CNTRL(1));
+ /*
+ * Ensure that SIGDET is disabled before PHY power
+ * collapse
+ */
+ mb();
+ }
+ writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * ensure that PHY knows its PHY analog rail is going
+ * to be powered down
+ */
+ mb();
+ }
+}
+
+static
+void ufs_qcom_phy_qmp_28nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+ phy_common->quirks = UFS_QCOM_PHY_QUIRK_CFG_RESTORE
+ | UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_28nm_init(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy_qmp_28nm *phy = phy_get_drvdata(generic_phy);
+ struct ufs_qcom_phy *phy_common = &phy->common_cfg;
+ int err = 0;
+
+ err = ufs_qcom_phy_init_clks(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ ufs_qcom_phy_qmp_28nm_advertise_quirks(phy_common);
+
+out:
+ return err;
+}
+
+static int ufs_qcom_phy_qmp_28nm_calibrate(struct ufs_qcom_phy *ufs_qcom_phy)
+{
+ struct ufs_qcom_phy_calibration *tbl_A = NULL, *tbl_B;
+ int tbl_size_A = 0, tbl_size_B;
+ int rate = UFS_QCOM_LIMIT_HS_RATE;
+ u8 major = ufs_qcom_phy->host_ctrl_rev_major;
+ u16 minor = ufs_qcom_phy->host_ctrl_rev_minor;
+ u16 step = ufs_qcom_phy->host_ctrl_rev_step;
+ int err;
+
+ if ((major == 0x1) && (minor == 0x001) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_ctrl_1_1_0_rate_A);
+ tbl_A = phy_cal_table_ctrl_1_1_0_rate_A;
+ } else if ((major == 0x1) && (minor == 0x001) && (step == 0x0001)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_ctrl_1_1_1_rate_A);
+ tbl_A = phy_cal_table_ctrl_1_1_1_rate_A;
+ }
+
+ tbl_B = phy_cal_table_rate_B;
+ tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+
+ err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A,
+ tbl_B, tbl_size_B, rate);
+ if (err)
+ dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n",
+ __func__, err);
+
+ return err;
+}
+
+static
+u32 ufs_qcom_phy_qmp_28nm_read_attr(struct ufs_qcom_phy *phy_common, u32 attr)
+
+{
+ u32 l0, l1;
+
+ writel_relaxed(attr, phy_common->mmio + UFS_PHY_RMMI_ATTRID);
+ /* Read attribute value for both lanes */
+ writel_relaxed((UFS_PHY_RMMI_CFGRD_L0 | UFS_PHY_RMMI_CFGRD_L1),
+ phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+
+ l0 = readl_relaxed(phy_common->mmio + UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS);
+ l1 = readl_relaxed(phy_common->mmio + UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS);
+ /* Both lanes should have the same value for same attribute type */
+ if (unlikely(l0 != l1))
+ dev_warn(phy_common->dev, "%s: attr 0x%x values are not same for Lane-0 and Lane-1, l0=0x%x, l1=0x%x",
+ __func__, attr, l0, l1);
+
+ /* must clear now */
+ writel_relaxed(0x00, phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+
+ return l0;
+}
+
+static void
+ufs_qcom_phy_qmp_28nm_write_attr(struct ufs_qcom_phy *phy_common,
+ u32 attr, u32 val)
+{
+ writel_relaxed(attr, phy_common->mmio + UFS_PHY_RMMI_ATTRID);
+ writel_relaxed(val, phy_common->mmio + UFS_PHY_RMMI_ATTRWRVAL);
+ /* update attribute for both lanes */
+ writel_relaxed((UFS_PHY_RMMI_CFGWR_L0 | UFS_PHY_RMMI_CFGWR_L1),
+ phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+ if (is_mphy_tx_attr(attr))
+ writel_relaxed((UFS_PHY_RMMI_TX_CFGUPDT_L0 |
+ UFS_PHY_RMMI_TX_CFGUPDT_L1),
+ phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+ else
+ writel_relaxed((UFS_PHY_RMMI_RX_CFGUPDT_L0 |
+ UFS_PHY_RMMI_RX_CFGUPDT_L1),
+ phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+
+ writel_relaxed(0x00, phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL);
+}
+
+static
+void ufs_qcom_phy_qmp_28nm_save_configuration(struct ufs_qcom_phy *phy_common)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cached_phy_regs); i++)
+ cached_phy_regs[i].cfg_value =
+ readl_relaxed(phy_common->mmio +
+ cached_phy_regs[i].reg_offset);
+
+ for (i = 0; i < ARRAY_SIZE(cached_phy_attr); i++)
+ cached_phy_attr[i].value =
+ ufs_qcom_phy_qmp_28nm_read_attr(phy_common,
+ cached_phy_attr[i].att);
+}
+
+static void
+ufs_qcom_phy_qmp_28nm_restore_configuration(struct ufs_qcom_phy *phy_common)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cached_phy_attr); i++)
+ ufs_qcom_phy_qmp_28nm_write_attr(phy_common,
+ cached_phy_attr[i].att, cached_phy_attr[i].value);
+}
+
+static
+void ufs_qcom_phy_qmp_28nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+ writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK,
+ phy->mmio + UFS_PHY_TX_LANE_ENABLE);
+ mb();
+}
+
+static inline void ufs_qcom_phy_qmp_28nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+ u32 tmp;
+
+ tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+ tmp &= ~MASK_SERDES_START;
+ tmp |= (1 << OFFSET_SERDES_START);
+ writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+ mb();
+}
+
+static int ufs_qcom_phy_qmp_28nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+ int err = 0;
+ u32 val;
+
+ err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+ val, (val & MASK_PCS_READY), 10, 1000000);
+ if (err)
+ dev_err(phy_common->dev, "%s: phy init failed, %d\n",
+ __func__, err);
+
+ return err;
+}
+
+struct phy_ops ufs_qcom_phy_qmp_28nm_phy_ops = {
+ .init = ufs_qcom_phy_qmp_28nm_init,
+ .exit = ufs_qcom_phy_exit,
+ .power_on = ufs_qcom_phy_power_on,
+ .power_off = ufs_qcom_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+struct ufs_qcom_phy_specific_ops phy_28nm_ops = {
+ .calibrate_phy = ufs_qcom_phy_qmp_28nm_calibrate,
+ .start_serdes = ufs_qcom_phy_qmp_28nm_start_serdes,
+ .save_configuration = ufs_qcom_phy_qmp_28nm_save_configuration,
+ .restore_configuration = ufs_qcom_phy_qmp_28nm_restore_configuration,
+ .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_28nm_is_pcs_ready,
+ .set_tx_lane_enable = ufs_qcom_phy_qmp_28nm_set_tx_lane_enable,
+ .power_control = ufs_qcom_phy_qmp_28nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_28nm_probe(struct platform_device *pdev)
+{
+ struct ufs_qcom_phy_qmp_28nm *phy;
+ struct device *dev = &pdev->dev;
+ int err = 0;
+ struct phy *generic_phy;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ err = -ENOMEM;
+ dev_err(dev, "%s: failed to allocate phy\n", __func__);
+ goto out;
+ }
+
+ phy->common_cfg.cached_regs =
+ (struct ufs_qcom_phy_calibration *)cached_phy_regs;
+ phy->common_cfg.cached_regs_table_size =
+ ARRAY_SIZE(cached_phy_regs);
+
+ generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg,
+ &ufs_qcom_phy_qmp_28nm_phy_ops, &phy_28nm_ops);
+
+ if (!generic_phy) {
+ dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n",
+ __func__);
+ err = -EIO;
+ goto out;
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+
+ strlcpy(phy->common_cfg.name, UFS_PHY_NAME,
+ sizeof(phy->common_cfg.name));
+
+out:
+ return err;
+}
+
+static int ufs_qcom_phy_qmp_28nm_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy = to_phy(dev);
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int err = 0;
+
+ err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy);
+ if (err)
+ dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n",
+ __func__, err);
+
+ return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_28nm_of_match[] = {
+ {.compatible = "qcom,ufs-phy-qmp-28nm"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_28nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_28nm_driver = {
+ .probe = ufs_qcom_phy_qmp_28nm_probe,
+ .remove = ufs_qcom_phy_qmp_28nm_remove,
+ .driver = {
+ .of_match_table = ufs_qcom_phy_qmp_28nm_of_match,
+ .name = "ufs_qcom_phy_qmp_28nm",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_28nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 28nm");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-qcom-ufs-qmp-28nm.h b/drivers/phy/phy-qcom-ufs-qmp-28nm.h
new file mode 100644
index 0000000..b406d99
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-28nm.h
@@ -0,0 +1,738 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_QMP_28NM_H_
+#define UFS_QCOM_PHY_QMP_28NM_H_
+
+#include <linux/phy/phy-qcom-ufs.h>
+
+/* QCOM UFS PHY control registers */
+
+#define COM_OFF(x) (0x000 + x)
+#define PHY_OFF(x) (0x700 + x)
+#define TX_OFF(n, x) (0x100 + (0x400 * n) + x)
+#define RX_OFF(n, x) (0x200 + (0x400 * n) + x)
+
+/* UFS PHY PLL block registers */
+#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x00)
+#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04)
+#define QSERDES_COM_CMN_MODE COM_OFF(0x08)
+#define QSERDES_COM_IE_TRIM COM_OFF(0x0C)
+#define QSERDES_COM_IP_TRIM COM_OFF(0x10)
+#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14)
+#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x18)
+#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x1C)
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x20)
+#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x24)
+#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x28)
+#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x2C)
+#define QSERDES_COM_ATB_SEL1 COM_OFF(0x30)
+#define QSERDES_COM_ATB_SEL2 COM_OFF(0x34)
+#define QSERDES_COM_SYSCLK_EN_SEL COM_OFF(0x38)
+#define QSERDES_COM_RES_CODE_TXBAND COM_OFF(0x3C)
+#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x40)
+#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x44)
+#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x48)
+#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x4C)
+#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x50)
+#define QSERDES_COM_RES_TRIM_OFFSET COM_OFF(0x54)
+#define QSERDES_COM_BGTC COM_OFF(0x58)
+#define QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP COM_OFF(0x5C)
+#define QSERDES_COM_PLL_VCO_TUNE COM_OFF(0x60)
+#define QSERDES_COM_DEC_START1 COM_OFF(0x64)
+#define QSERDES_COM_PLL_AMP_OS COM_OFF(0x68)
+#define QSERDES_COM_SSC_EN_CENTER COM_OFF(0x6C)
+#define QSERDES_COM_SSC_ADJ_PER1 COM_OFF(0x70)
+#define QSERDES_COM_SSC_ADJ_PER2 COM_OFF(0x74)
+#define QSERDES_COM_SSC_PER1 COM_OFF(0x78)
+#define QSERDES_COM_SSC_PER2 COM_OFF(0x7C)
+#define QSERDES_COM_SSC_STEP_SIZE1 COM_OFF(0x80)
+#define QSERDES_COM_SSC_STEP_SIZE2 COM_OFF(0x84)
+#define QSERDES_COM_RES_TRIM_SEARCH COM_OFF(0x88)
+#define QSERDES_COM_RES_TRIM_FREEZE COM_OFF(0x8C)
+#define QSERDES_COM_RES_TRIM_EN_VCOCALDONE COM_OFF(0x90)
+#define QSERDES_COM_FAUX_EN COM_OFF(0x94)
+#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x98)
+#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x9C)
+#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0xA0)
+#define QSERDES_COM_DEC_START2 COM_OFF(0xA4)
+#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0xA8)
+#define QSERDES_COM_PLL_CRCTRL COM_OFF(0xAC)
+#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0xB0)
+#define QSERDES_COM_PLL_FREQUPDATE COM_OFF(0xB4)
+#define QSERDES_COM_PLL_VCO_HIGH COM_OFF(0xB8)
+#define QSERDES_COM_RESET_SM COM_OFF(0xBC)
+
+/* UFS PHY registers */
+#define UFS_PHY_PHY_START PHY_OFF(0x00)
+#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x04)
+#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08)
+#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C)
+#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10)
+#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14)
+#define UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB PHY_OFF(0x18)
+#define UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB PHY_OFF(0x1C)
+#define UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB PHY_OFF(0x20)
+#define UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB PHY_OFF(0x24)
+#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28)
+#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C)
+#define UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE PHY_OFF(0x30)
+#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34)
+#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38)
+#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C)
+#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40)
+#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44)
+#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48)
+#define UFS_PHY_RETIME_BUFFER_EN PHY_OFF(0x4C)
+#define UFS_PHY_PLL_CNTL PHY_OFF(0x50)
+#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54)
+#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58)
+#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C)
+#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60)
+#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64)
+#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68)
+#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C)
+#define UFS_PHY_L0_BIST_CTRL PHY_OFF(0x70)
+#define UFS_PHY_L1_BIST_CTRL PHY_OFF(0x74)
+#define UFS_PHY_BIST_PRBS_POLY0 PHY_OFF(0x78)
+#define UFS_PHY_BIST_PRBS_POLY1 PHY_OFF(0x7C)
+#define UFS_PHY_BIST_PRBS_SEED0 PHY_OFF(0x80)
+#define UFS_PHY_BIST_PRBS_SEED1 PHY_OFF(0x84)
+#define UFS_PHY_BIST_FIXED_PAT_CTRL PHY_OFF(0x88)
+#define UFS_PHY_BIST_FIXED_PAT0_DATA PHY_OFF(0x8C)
+#define UFS_PHY_BIST_FIXED_PAT1_DATA PHY_OFF(0x90)
+#define UFS_PHY_BIST_FIXED_PAT2_DATA PHY_OFF(0x94)
+#define UFS_PHY_BIST_FIXED_PAT3_DATA PHY_OFF(0x98)
+#define UFS_PHY_TX_HSGEAR_CAPABILITY PHY_OFF(0x9C)
+#define UFS_PHY_TX_PWMGEAR_CAPABILITY PHY_OFF(0xA0)
+#define UFS_PHY_TX_AMPLITUDE_CAPABILITY PHY_OFF(0xA4)
+#define UFS_PHY_TX_EXTERNALSYNC_CAPABILITY PHY_OFF(0xA8)
+#define UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY PHY_OFF(0xAC)
+#define UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY PHY_OFF(0xB0)
+#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4)
+#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8)
+#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC)
+#define UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY PHY_OFF(0xC0)
+#define UFS_PHY_TX_PHY_MAJORMINOR_RELEASE_CAPABILITY PHY_OFF(0xC4)
+#define UFS_PHY_TX_PHY_EDITORIAL_RELEASE_CAPABILITY PHY_OFF(0xC8)
+#define UFS_PHY_TX_HIBERN8TIME_CAPABILITY PHY_OFF(0xCC)
+#define UFS_PHY_RX_HSGEAR_CAPABILITY PHY_OFF(0xD0)
+#define UFS_PHY_RX_PWMGEAR_CAPABILITY PHY_OFF(0xD4)
+#define UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY PHY_OFF(0xD8)
+#define UFS_PHY_RX_LS_TERMINATED_CAPABILITY PHY_OFF(0xDC)
+#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0)
+#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4)
+#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8)
+#define UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY PHY_OFF(0xEC)
+#define UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY PHY_OFF(0xF0)
+#define UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY PHY_OFF(0xF4)
+#define UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY PHY_OFF(0xF8)
+#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC)
+#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100)
+#define UFS_PHY_RX_PHY_MAJORMINOR_RELEASE_CAPABILITY PHY_OFF(0x104)
+#define UFS_PHY_RX_PHY_EDITORIAL_RELEASE_CAPABILITY PHY_OFF(0x108)
+#define UFS_PHY_RX_HIBERN8TIME_CAPABILITY PHY_OFF(0x10C)
+#define UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY PHY_OFF(0x110)
+#define UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY PHY_OFF(0x114)
+#define UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY PHY_OFF(0x118)
+#define UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY PHY_OFF(0x11C)
+#define UFS_PHY_DEBUG_BUS_SEL PHY_OFF(0x120)
+#define UFS_PHY_DEBUG_BUS_0_STATUS_CHK PHY_OFF(0x124)
+#define UFS_PHY_DEBUG_BUS_1_STATUS_CHK PHY_OFF(0x128)
+#define UFS_PHY_DEBUG_BUS_2_STATUS_CHK PHY_OFF(0x12C)
+#define UFS_PHY_DEBUG_BUS_3_STATUS_CHK PHY_OFF(0x130)
+#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x134)
+#define UFS_PHY_L0_BIST_CHK_ERR_CNT_L_STATUS PHY_OFF(0x138)
+#define UFS_PHY_L0_BIST_CHK_ERR_CNT_H_STATUS PHY_OFF(0x13C)
+#define UFS_PHY_L1_BIST_CHK_ERR_CNT_L_STATUS PHY_OFF(0x140)
+#define UFS_PHY_L1_BIST_CHK_ERR_CNT_H_STATUS PHY_OFF(0x144)
+#define UFS_PHY_L0_BIST_CHK_STATUS PHY_OFF(0x148)
+#define UFS_PHY_L1_BIST_CHK_STATUS PHY_OFF(0x14C)
+#define UFS_PHY_DEBUG_BUS_0_STATUS PHY_OFF(0x150)
+#define UFS_PHY_DEBUG_BUS_1_STATUS PHY_OFF(0x154)
+#define UFS_PHY_DEBUG_BUS_2_STATUS PHY_OFF(0x158)
+#define UFS_PHY_DEBUG_BUS_3_STATUS PHY_OFF(0x15C)
+#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x16C)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6)
+#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5)
+#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2)
+#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1)
+#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0)
+#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x170)
+#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x174)
+#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x178)
+#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x17C)
+
+/* TX LANE n (0, 1) registers */
+#define QSERDES_TX_BIST_MODE_LANENO(n) TX_OFF(n, 0x00)
+#define QSERDES_TX_CLKBUF_ENABLE(n) TX_OFF(n, 0x04)
+#define QSERDES_TX_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08)
+#define QSERDES_TX_TX_DRV_LVL(n) TX_OFF(n, 0x0C)
+#define QSERDES_TX_RESET_TSYNC_EN(n) TX_OFF(n, 0x10)
+#define QSERDES_TX_LPB_EN(n) TX_OFF(n, 0x14)
+#define QSERDES_TX_RES_CODE(n) TX_OFF(n, 0x18)
+#define QSERDES_TX_PERL_LENGTH1(n) TX_OFF(n, 0x1C)
+#define QSERDES_TX_PERL_LENGTH2(n) TX_OFF(n, 0x20)
+#define QSERDES_TX_SERDES_BYP_EN_OUT(n) TX_OFF(n, 0x24)
+#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(n) TX_OFF(n, 0x28)
+#define QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(n) TX_OFF(n, 0x2C)
+#define QSERDES_TX_BIST_PATTERN1(n) TX_OFF(n, 0x30)
+#define QSERDES_TX_BIST_PATTERN2(n) TX_OFF(n, 0x34)
+#define QSERDES_TX_BIST_PATTERN3(n) TX_OFF(n, 0x38)
+#define QSERDES_TX_BIST_PATTERN4(n) TX_OFF(n, 0x3C)
+#define QSERDES_TX_BIST_PATTERN5(n) TX_OFF(n, 0x40)
+#define QSERDES_TX_BIST_PATTERN6(n) TX_OFF(n, 0x44)
+#define QSERDES_TX_BIST_PATTERN7(n) TX_OFF(n, 0x48)
+#define QSERDES_TX_BIST_PATTERN8(n) TX_OFF(n, 0x4C)
+#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x50)
+#define QSERDES_TX_ATB_SEL(n) TX_OFF(n, 0x54)
+#define QSERDES_TX_REC_DETECT_LVL(n) TX_OFF(n, 0x58)
+#define QSERDES_TX_PRBS_SEED1(n) TX_OFF(n, 0x5C)
+#define QSERDES_TX_PRBS_SEED2(n) TX_OFF(n, 0x60)
+#define QSERDES_TX_PRBS_SEED3(n) TX_OFF(n, 0x64)
+#define QSERDES_TX_PRBS_SEED4(n) TX_OFF(n, 0x68)
+#define QSERDES_TX_RESET_GEN(n) TX_OFF(n, 0x6C)
+#define QSERDES_TX_TRAN_DRVR_EMP_EN(n) TX_OFF(n, 0x70)
+#define QSERDES_TX_TX_INTERFACE_MODE(n) TX_OFF(n, 0x74)
+#define QSERDES_TX_BIST_STATUS(n) TX_OFF(n, 0x78)
+#define QSERDES_TX_BIST_ERROR_COUNT1(n) TX_OFF(n, 0x7C)
+#define QSERDES_TX_BIST_ERROR_COUNT2(n) TX_OFF(n, 0x80)
+
+/* RX LANE n (0, 1) registers */
+#define QSERDES_RX_CDR_CONTROL(n) RX_OFF(n, 0x00)
+#define QSERDES_RX_AUX_CONTROL(n) RX_OFF(n, 0x04)
+#define QSERDES_RX_AUX_DATA_TCODE(n) RX_OFF(n, 0x08)
+#define QSERDES_RX_RCLK_AUXDATA_SEL(n) RX_OFF(n, 0x0C)
+#define QSERDES_RX_EQ_CONTROL(n) RX_OFF(n, 0x10)
+#define QSERDES_RX_RX_EQ_GAIN2(n) RX_OFF(n, 0x14)
+#define QSERDES_RX_AC_JTAG_INIT(n) RX_OFF(n, 0x18)
+#define QSERDES_RX_AC_JTAG_LVL_EN(n) RX_OFF(n, 0x1C)
+#define QSERDES_RX_AC_JTAG_MODE(n) RX_OFF(n, 0x20)
+#define QSERDES_RX_AC_JTAG_RESET(n) RX_OFF(n, 0x24)
+#define QSERDES_RX_RX_IQ_RXDET_EN(n) RX_OFF(n, 0x28)
+#define QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(n) RX_OFF(n, 0x2C)
+#define QSERDES_RX_RX_EQ_GAIN1(n) RX_OFF(n, 0x30)
+#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x34)
+#define QSERDES_RX_RX_BAND(n) RX_OFF(n, 0x38)
+#define QSERDES_RX_CDR_FREEZE_UP_DN(n) RX_OFF(n, 0x3C)
+#define QSERDES_RX_RX_INTERFACE_MODE(n) RX_OFF(n, 0x40)
+#define QSERDES_RX_JITTER_GEN_MODE(n) RX_OFF(n, 0x44)
+#define QSERDES_RX_BUJ_AMP(n) RX_OFF(n, 0x48)
+#define QSERDES_RX_SJ_AMP1(n) RX_OFF(n, 0x4C)
+#define QSERDES_RX_SJ_AMP2(n) RX_OFF(n, 0x50)
+#define QSERDES_RX_SJ_PER1(n) RX_OFF(n, 0x54)
+#define QSERDES_RX_SJ_PER2(n) RX_OFF(n, 0x58)
+#define QSERDES_RX_BUJ_STEP_FREQ1(n) RX_OFF(n, 0x5C)
+#define QSERDES_RX_BUJ_STEP_FREQ2(n) RX_OFF(n, 0x60)
+#define QSERDES_RX_PPM_OFFSET1(n) RX_OFF(n, 0x64)
+#define QSERDES_RX_PPM_OFFSET2(n) RX_OFF(n, 0x68)
+#define QSERDES_RX_SIGN_PPM_PERIOD1(n) RX_OFF(n, 0x6C)
+#define QSERDES_RX_SIGN_PPM_PERIOD2(n) RX_OFF(n, 0x70)
+#define QSERDES_RX_SSC_CTRL(n) RX_OFF(n, 0x74)
+#define QSERDES_RX_SSC_COUNT1(n) RX_OFF(n, 0x78)
+#define QSERDES_RX_SSC_COUNT2(n) RX_OFF(n, 0x7C)
+#define QSERDES_RX_PWM_CNTRL1(n) RX_OFF(n, 0x80)
+#define QSERDES_RX_PWM_CNTRL2(n) RX_OFF(n, 0x84)
+#define QSERDES_RX_PWM_NDIV(n) RX_OFF(n, 0x88)
+#define QSERDES_RX_SIGDET_CNTRL2(n) RX_OFF(n, 0x8C)
+#define QSERDES_RX_UFS_CNTRL(n) RX_OFF(n, 0x90)
+#define QSERDES_RX_CDR_CONTROL3(n) RX_OFF(n, 0x94)
+#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x98)
+#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0x9C)
+#define QSERDES_RX_CDR_CONTROL_EIGHTH(n) RX_OFF(n, 0xA0)
+#define QSERDES_RX_UCDR_FO_GAIN(n) RX_OFF(n, 0xA4)
+#define QSERDES_RX_UCDR_SO_GAIN(n) RX_OFF(n, 0xA8)
+#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(n) RX_OFF(n, 0xAC)
+#define QSERDES_RX_UCDR_FO_TO_SO_DELAY(n) RX_OFF(n, 0xB0)
+#define QSERDES_RX_PI_CTRL1(n) RX_OFF(n, 0xB4)
+#define QSERDES_RX_PI_CTRL2(n) RX_OFF(n, 0xB8)
+#define QSERDES_RX_PI_QUAD(n) RX_OFF(n, 0xBC)
+#define QSERDES_RX_IDATA1(n) RX_OFF(n, 0xC0)
+#define QSERDES_RX_IDATA2(n) RX_OFF(n, 0xC4)
+#define QSERDES_RX_AUX_DATA1(n) RX_OFF(n, 0xC8)
+#define QSERDES_RX_AUX_DATA2(n) RX_OFF(n, 0xCC)
+#define QSERDES_RX_AC_JTAG_OUTP(n) RX_OFF(n, 0xD0)
+#define QSERDES_RX_AC_JTAG_OUTN(n) RX_OFF(n, 0xD4)
+#define QSERDES_RX_RX_SIGDET_PWMDECSTATUS(n) RX_OFF(n, 0xD8)
+
+#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3
+
+/*
+ * This structure represents the 28nm specific phy.
+ * common_cfg MUST remain the first field in this structure
+ * in case extra fields are added. This way, when calling
+ * get_ufs_qcom_phy() of generic phy, we can extract the
+ * common phy structure (struct ufs_qcom_phy) out of it
+ * regardless of the relevant specific phy.
+ */
+struct ufs_qcom_phy_qmp_28nm {
+ struct ufs_qcom_phy common_cfg;
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_ctrl_1_1_0_rate_A[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xFF),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x24),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x67),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x13),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(0), 0x43),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(1), 0x43),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(0), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x2a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(1), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x2a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(0), 0xC0),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(1), 0xC0),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(0), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(1), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G1_CLK_DIVIDER, 0x50),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G2_CLK_DIVIDER, 0x28),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G3_CLK_DIVIDER, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G4_CLK_DIVIDER, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER, 0xa8),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER, 0x54),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER, 0x2a),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER, 0x15),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_OMC_STATUS_RDVAL, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_TIME, 0x1f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_GRANULARITY, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TSYNC_RSYNC_CNTL, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PLL_CNTL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x1a),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CFG_CHANGE_CNT_VAL, 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYNC_WAIT_TIME, 0x30),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0xc8),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(0), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(0), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(1), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(1), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_TRIM_OFFSET, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BGTC, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_AMP_OS, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(0), 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(1), 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(0), 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(1), 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(0), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(1), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB, 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB, 0x27),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RETIME_BUFFER_EN, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HSGEAR_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_PWMGEAR_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_AMPLITUDE_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_EXTERNALSYNC_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HIBERN8TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HSGEAR_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWMGEAR_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_TERMINATED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY, 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HIBERN8TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(0), 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(0), 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(0), 0x73),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(0), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(0), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(0), 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(0), 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(0), 0x35),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(1), 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(1), 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(1), 0x73),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(1), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(1), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(1), 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(1), 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(1), 0x35),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MODE, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IE_TRIM, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IP_TRIM, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_IN_SYNC_SEL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_FAUX_EN, 0x00),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_ctrl_1_1_1_rate_A[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0x43),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x24),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(0), 0x43),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(1), 0x43),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(0), 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(1), 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(0), 0xC0),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(1), 0xC0),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(0), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(1), 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G1_CLK_DIVIDER, 0x30),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G2_CLK_DIVIDER, 0x18),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G3_CLK_DIVIDER, 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G4_CLK_DIVIDER, 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER, 0xa8),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER, 0x54),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER, 0x2a),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER, 0x15),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_OMC_STATUS_RDVAL, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_TIME, 0x1f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_GRANULARITY, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TSYNC_RSYNC_CNTL, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PLL_CNTL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x1a),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CFG_CHANGE_CNT_VAL, 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYNC_WAIT_TIME, 0x30),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0xc8),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(0), 0x1f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(0), 0x17),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(1), 0x1f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(1), 0x17),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_TRIM_OFFSET, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BGTC, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_AMP_OS, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(0), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(1), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB, 0x07),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB, 0x27),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RETIME_BUFFER_EN, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HSGEAR_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_PWMGEAR_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_AMPLITUDE_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_EXTERNALSYNC_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HIBERN8TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HSGEAR_CAPABILITY, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWMGEAR_CAPABILITY, 0x04),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_TERMINATED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY,
+ 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY, 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HIBERN8TIME_CAPABILITY, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY, 0x48),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY,
+ 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY,
+ 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(0), 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(0), 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(0), 0x51),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(0), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(0), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(0), 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(0), 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(0), 0x35),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(1), 0x09),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(1), 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(1), 0x51),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(1), 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(1), 0x22),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(1), 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(1), 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(
+ QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(1), 0x35),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MODE, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IE_TRIM, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IP_TRIM, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_IN_SYNC_SEL, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_FAUX_EN, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x08),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1E),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+};
+
+static struct ufs_qcom_phy_calibration cached_phy_regs[] = {
+ {QSERDES_COM_PLL_CRCTRL},
+ {QSERDES_COM_PLL_CNTRL},
+ {QSERDES_COM_SYSCLK_EN_SEL},
+ {QSERDES_COM_SYS_CLK_CTRL},
+ {QSERDES_COM_PLL_CLKEPDIV},
+ {QSERDES_COM_DEC_START1},
+ {QSERDES_COM_DEC_START2},
+ {QSERDES_COM_DIV_FRAC_START1},
+ {QSERDES_COM_DIV_FRAC_START2},
+ {QSERDES_COM_DIV_FRAC_START3},
+ {QSERDES_COM_PLLLOCK_CMP1},
+ {QSERDES_COM_PLLLOCK_CMP2},
+ {QSERDES_COM_PLLLOCK_CMP3},
+ {QSERDES_COM_PLLLOCK_CMP_EN},
+ {QSERDES_COM_RESETSM_CNTRL},
+ {QSERDES_COM_PLL_RXTXEPCLK_EN},
+ {QSERDES_RX_PWM_CNTRL1(0)},
+ {QSERDES_RX_PWM_CNTRL1(1)},
+ {QSERDES_RX_CDR_CONTROL(0)},
+ {QSERDES_RX_CDR_CONTROL_HALF(0)},
+ {QSERDES_RX_CDR_CONTROL_QUARTER(0)},
+ {QSERDES_RX_CDR_CONTROL(1)},
+ {QSERDES_RX_CDR_CONTROL_HALF(1)},
+ {QSERDES_RX_CDR_CONTROL_QUARTER(1)},
+ {QSERDES_RX_SIGDET_CNTRL(0)},
+ {QSERDES_RX_SIGDET_CNTRL(1)},
+ {QSERDES_RX_SIGDET_CNTRL2(0)},
+ {QSERDES_RX_SIGDET_CNTRL2(1)},
+ {QSERDES_RX_RX_EQ_GAIN1(0)},
+ {QSERDES_RX_RX_EQ_GAIN2(0)},
+ {QSERDES_RX_RX_EQ_GAIN1(1)},
+ {QSERDES_RX_RX_EQ_GAIN2(1)},
+ {QSERDES_COM_PLL_IP_SETI},
+ {QSERDES_COM_PLL_CP_SETI},
+ {QSERDES_COM_PLL_IP_SETP},
+ {QSERDES_COM_PLL_CP_SETP},
+ {UFS_PHY_PWM_G1_CLK_DIVIDER},
+ {UFS_PHY_PWM_G2_CLK_DIVIDER},
+ {UFS_PHY_PWM_G3_CLK_DIVIDER},
+ {UFS_PHY_PWM_G4_CLK_DIVIDER},
+ {UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER},
+ {UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER},
+ {UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER},
+ {UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER},
+ {UFS_PHY_OMC_STATUS_RDVAL},
+ {UFS_PHY_LINE_RESET_TIME},
+ {UFS_PHY_LINE_RESET_GRANULARITY},
+ {UFS_PHY_TSYNC_RSYNC_CNTL},
+ {UFS_PHY_PLL_CNTL},
+ {UFS_PHY_TX_LARGE_AMP_DRV_LVL},
+ {UFS_PHY_TX_SMALL_AMP_DRV_LVL},
+ {UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL},
+ {UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL},
+ {UFS_PHY_CFG_CHANGE_CNT_VAL},
+ {UFS_PHY_RX_SYNC_WAIT_TIME},
+ {UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY},
+ {UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY},
+ {UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY},
+ {UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY},
+ {UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY},
+ {UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY},
+ {UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY},
+ {UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY},
+ {QSERDES_RX_CDR_CONTROL3(0)},
+ {QSERDES_RX_CDR_CONTROL3(1)},
+ {QSERDES_COM_RES_TRIM_OFFSET},
+ {QSERDES_COM_BGTC},
+ {QSERDES_COM_PLL_AMP_OS},
+};
+
+static struct ufs_qcom_phy_stored_attributes cached_phy_attr[] = {
+ {TX_MODE},
+ {TX_HSRATE_SERIES},
+ {TX_HSGEAR},
+ {TX_PWMGEAR},
+ {TX_AMPLITUDE},
+ {TX_HS_SLEWRATE},
+ {TX_SYNC_SOURCE},
+ {TX_HS_PREPARE_LENGTH},
+ {TX_LS_PREPARE_LENGTH},
+ {TX_LCC_ENABLE},
+ {TX_PWM_BURST_CLOSURE_EXTENSION},
+ {TX_BYPASS_8B10B_ENABLE},
+ {TX_DRIVER_POLARITY},
+ {TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE},
+ {TX_LS_TERMINATED_LINE_DRIVE_ENABLE},
+ {TX_LCC_SEQUENCER},
+ {TX_MIN_ACTIVATETIME},
+ {TX_PWM_G6_G7_SYNC_LENGTH},
+ {RX_MODE},
+ {RX_HSRATE_SERIES},
+ {RX_HSGEAR},
+ {RX_PWMGEAR},
+ {RX_LS_TERMINATED_ENABLE},
+ {RX_HS_UNTERMINATED_ENABLE},
+ {RX_ENTER_HIBERN8},
+ {RX_BYPASS_8B10B_ENABLE},
+ {RX_TERMINATION_FORCE_ENABLE},
+};
+
+#endif
diff --git a/drivers/phy/phy-qcom-ufs.c b/drivers/phy/phy-qcom-ufs.c
new file mode 100644
index 0000000..9ba6adf
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs.c
@@ -0,0 +1,777 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <linux/phy/phy-qcom-ufs.h>
+
+static int __ufs_qcom_phy_init_vreg(struct phy *, struct ufs_qcom_phy_vreg *,
+ const char *, bool);
+static int ufs_qcom_phy_init_vreg(struct phy *, struct ufs_qcom_phy_vreg *,
+ const char *);
+
+int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ struct ufs_qcom_phy_calibration *tbl_A,
+ int tbl_size_A,
+ struct ufs_qcom_phy_calibration *tbl_B,
+ int tbl_size_B, int rate)
+{
+ int i;
+ int ret = 0;
+
+ if (!tbl_A) {
+ dev_err(ufs_qcom_phy->dev, "%s: tbl_A is NULL", __func__);
+ ret = EINVAL;
+ goto out;
+ }
+
+ for (i = 0; i < tbl_size_A; i++)
+ writel_relaxed(tbl_A[i].cfg_value,
+ ufs_qcom_phy->mmio + tbl_A[i].reg_offset);
+
+ /*
+ * In case we would like to work in rate B, we need
+ * to override a registers that were configured in rate A table
+ * with registers of rate B table.
+ * table.
+ */
+ if (rate == PA_HS_MODE_B) {
+ if (!tbl_B) {
+ dev_err(ufs_qcom_phy->dev, "%s: tbl_B is NULL",
+ __func__);
+ ret = EINVAL;
+ goto out;
+ }
+
+ for (i = 0; i < tbl_size_B; i++)
+ writel_relaxed(tbl_B[i].cfg_value,
+ ufs_qcom_phy->mmio + tbl_B[i].reg_offset);
+ }
+
+ /* flush buffered writes */
+ mb();
+
+out:
+ return ret;
+}
+
+struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
+ struct ufs_qcom_phy *common_cfg,
+ struct phy_ops *ufs_qcom_phy_gen_ops,
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops)
+{
+ int err;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy = NULL;
+ struct phy_provider *phy_provider;
+
+ err = ufs_qcom_phy_base_init(pdev, common_cfg);
+ if (err) {
+ dev_err(dev, "%s: phy base init failed %d\n", __func__, err);
+ goto out;
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ err = PTR_ERR(phy_provider);
+ dev_err(dev, "%s: failed to register phy %d\n", __func__, err);
+ goto out;
+ }
+
+ generic_phy = devm_phy_create(dev, NULL, ufs_qcom_phy_gen_ops, NULL);
+ if (IS_ERR(generic_phy)) {
+ err = PTR_ERR(generic_phy);
+ dev_err(dev, "%s: failed to create phy %d\n", __func__, err);
+ goto out;
+ }
+
+ common_cfg->phy_spec_ops = phy_spec_ops;
+ common_cfg->dev = dev;
+
+out:
+ return generic_phy;
+}
+
+/*
+ * This assumes the embedded phy structure inside generic_phy is of type
+ * struct ufs_qcom_phy. In order to function properly it's crucial
+ * to keep the embedded struct "struct ufs_qcom_phy common_cfg"
+ * as the first inside generic_phy.
+ */
+struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy)
+{
+ return (struct ufs_qcom_phy *)phy_get_drvdata(generic_phy);
+}
+
+int ufs_qcom_phy_base_init(struct platform_device *pdev,
+ struct ufs_qcom_phy *phy_common)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ int err = 0;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_mem");
+ if (!res) {
+ dev_err(dev, "%s: phy_mem resource not found\n", __func__);
+ err = -ENOMEM;
+ goto out;
+ }
+
+ phy_common->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy_common->mmio)) {
+ err = PTR_ERR(phy_common->mmio);
+ phy_common->mmio = NULL;
+ dev_err(dev, "%s: ioremap for phy_mem resource failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ /* "dev_ref_clk_ctrl_mem" is optional resource */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "dev_ref_clk_ctrl_mem");
+ if (!res) {
+ dev_dbg(dev, "%s: dev_ref_clk_ctrl_mem resource not found\n",
+ __func__);
+ goto out;
+ }
+
+ phy_common->dev_ref_clk_ctrl_mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy_common->dev_ref_clk_ctrl_mmio)) {
+ err = PTR_ERR(phy_common->dev_ref_clk_ctrl_mmio);
+ phy_common->dev_ref_clk_ctrl_mmio = NULL;
+ dev_err(dev, "%s: ioremap for dev_ref_clk_ctrl_mem resource failed %d\n",
+ __func__, err);
+ }
+
+out:
+ return err;
+}
+
+static int __ufs_qcom_phy_clk_get(struct phy *phy,
+ const char *name, struct clk **clk_out, bool err_print)
+{
+ struct clk *clk;
+ int err = 0;
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+ struct device *dev = ufs_qcom_phy->dev;
+
+ clk = devm_clk_get(dev, name);
+ if (IS_ERR(clk)) {
+ err = PTR_ERR(clk);
+ if (err_print)
+ dev_err(dev, "failed to get %s err %d", name, err);
+ } else {
+ *clk_out = clk;
+ }
+
+ return err;
+}
+
+int ufs_qcom_phy_clk_get(struct phy *phy,
+ const char *name, struct clk **clk_out)
+{
+ return __ufs_qcom_phy_clk_get(phy, name, clk_out, true);
+}
+
+int
+ufs_qcom_phy_init_clks(struct phy *generic_phy,
+ struct ufs_qcom_phy *phy_common)
+{
+ int err;
+
+ err = ufs_qcom_phy_clk_get(generic_phy, "tx_iface_clk",
+ &phy_common->tx_iface_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_clk_get(generic_phy, "rx_iface_clk",
+ &phy_common->rx_iface_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_clk_get(generic_phy, "ref_clk_src",
+ &phy_common->ref_clk_src);
+ if (err)
+ goto out;
+
+ /*
+ * "ref_clk_parent" is optional hence don't abort init if it's not
+ * found.
+ */
+ __ufs_qcom_phy_clk_get(generic_phy, "ref_clk_parent",
+ &phy_common->ref_clk_parent, false);
+
+ err = ufs_qcom_phy_clk_get(generic_phy, "ref_clk",
+ &phy_common->ref_clk);
+
+out:
+ return err;
+}
+
+int
+ufs_qcom_phy_init_vregulators(struct phy *generic_phy,
+ struct ufs_qcom_phy *phy_common)
+{
+ int err;
+
+ err = ufs_qcom_phy_init_vreg(generic_phy, &phy_common->vdda_pll,
+ "vdda-pll");
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_init_vreg(generic_phy, &phy_common->vdda_phy,
+ "vdda-phy");
+
+ if (err)
+ goto out;
+
+ /* vddp-ref-clk-* properties are optional */
+ __ufs_qcom_phy_init_vreg(generic_phy, &phy_common->vddp_ref_clk,
+ "vddp-ref-clk", true);
+out:
+ return err;
+}
+
+static int __ufs_qcom_phy_init_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg, const char *name, bool optional)
+{
+ int err = 0;
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+ struct device *dev = ufs_qcom_phy->dev;
+
+ char prop_name[MAX_PROP_NAME];
+
+ vreg->name = kstrdup(name, GFP_KERNEL);
+ if (!vreg->name) {
+ err = -ENOMEM;
+ goto out;
+ }
+
+ vreg->reg = devm_regulator_get(dev, name);
+ if (IS_ERR(vreg->reg)) {
+ err = PTR_ERR(vreg->reg);
+ vreg->reg = NULL;
+ if (!optional)
+ dev_err(dev, "failed to get %s, %d\n", name, err);
+ goto out;
+ }
+
+ if (dev->of_node) {
+ snprintf(prop_name, MAX_PROP_NAME, "%s-max-microamp", name);
+ err = of_property_read_u32(dev->of_node,
+ prop_name, &vreg->max_uA);
+ if (err && err != -EINVAL) {
+ dev_err(dev, "%s: failed to read %s\n",
+ __func__, prop_name);
+ goto out;
+ } else if (err == -EINVAL || !vreg->max_uA) {
+ if (regulator_count_voltages(vreg->reg) > 0) {
+ dev_err(dev, "%s: %s is mandatory\n",
+ __func__, prop_name);
+ goto out;
+ }
+ err = 0;
+ }
+ snprintf(prop_name, MAX_PROP_NAME, "%s-always-on", name);
+ if (of_get_property(dev->of_node, prop_name, NULL))
+ vreg->is_always_on = true;
+ else
+ vreg->is_always_on = false;
+ }
+
+ if (!strcmp(name, "vdda-pll")) {
+ vreg->max_uV = VDDA_PLL_MAX_UV;
+ vreg->min_uV = VDDA_PLL_MIN_UV;
+ } else if (!strcmp(name, "vdda-phy")) {
+ vreg->max_uV = VDDA_PHY_MAX_UV;
+ vreg->min_uV = VDDA_PHY_MIN_UV;
+ } else if (!strcmp(name, "vddp-ref-clk")) {
+ vreg->max_uV = VDDP_REF_CLK_MAX_UV;
+ vreg->min_uV = VDDP_REF_CLK_MIN_UV;
+ }
+
+out:
+ if (err)
+ kfree(vreg->name);
+ return err;
+}
+
+static int ufs_qcom_phy_init_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg, const char *name)
+{
+ return __ufs_qcom_phy_init_vreg(phy, vreg, name, false);
+}
+
+int ufs_qcom_phy_cfg_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg, bool on)
+{
+ int ret = 0;
+ struct regulator *reg = vreg->reg;
+ const char *name = vreg->name;
+ int min_uV;
+ int uA_load;
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+ struct device *dev = ufs_qcom_phy->dev;
+
+ BUG_ON(!vreg);
+
+ if (regulator_count_voltages(reg) > 0) {
+ min_uV = on ? vreg->min_uV : 0;
+ ret = regulator_set_voltage(reg, min_uV, vreg->max_uV);
+ if (ret) {
+ dev_err(dev, "%s: %s set voltage failed, err=%d\n",
+ __func__, name, ret);
+ goto out;
+ }
+ uA_load = on ? vreg->max_uA : 0;
+ ret = regulator_set_optimum_mode(reg, uA_load);
+ if (ret >= 0) {
+ /*
+ * regulator_set_optimum_mode() returns new regulator
+ * mode upon success.
+ */
+ ret = 0;
+ } else {
+ dev_err(dev, "%s: %s set optimum mode(uA_load=%d) failed, err=%d\n",
+ __func__, name, uA_load, ret);
+ goto out;
+ }
+ }
+out:
+ return ret;
+}
+
+int ufs_qcom_phy_enable_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+ struct device *dev = ufs_qcom_phy->dev;
+ int ret = 0;
+
+ if (!vreg || vreg->enabled)
+ goto out;
+
+ ret = ufs_qcom_phy_cfg_vreg(phy, vreg, true);
+ if (ret) {
+ dev_err(dev, "%s: ufs_qcom_phy_cfg_vreg() failed, err=%d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ ret = regulator_enable(vreg->reg);
+ if (ret) {
+ dev_err(dev, "%s: enable failed, err=%d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ vreg->enabled = true;
+out:
+ return ret;
+}
+
+int ufs_qcom_phy_enable_ref_clk(struct phy *generic_phy)
+{
+ int ret = 0;
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ if (phy->is_ref_clk_enabled)
+ goto out;
+
+ /*
+ * reference clock is propagated in a daisy-chained manner from
+ * source to phy, so ungate them at each stage.
+ */
+ ret = clk_prepare_enable(phy->ref_clk_src);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk_src enable failed %d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ /*
+ * "ref_clk_parent" is optional clock hence make sure that clk reference
+ * is available before trying to enable the clock.
+ */
+ if (phy->ref_clk_parent) {
+ ret = clk_prepare_enable(phy->ref_clk_parent);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk_parent enable failed %d\n",
+ __func__, ret);
+ goto out_disable_src;
+ }
+ }
+
+ ret = clk_prepare_enable(phy->ref_clk);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk enable failed %d\n",
+ __func__, ret);
+ goto out_disable_parent;
+ }
+
+ phy->is_ref_clk_enabled = true;
+ goto out;
+
+out_disable_parent:
+ if (phy->ref_clk_parent)
+ clk_disable_unprepare(phy->ref_clk_parent);
+out_disable_src:
+ clk_disable_unprepare(phy->ref_clk_src);
+out:
+ return ret;
+}
+
+int ufs_qcom_phy_disable_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+ struct device *dev = ufs_qcom_phy->dev;
+ int ret = 0;
+
+ if (!vreg || !vreg->enabled || vreg->is_always_on)
+ goto out;
+
+ ret = regulator_disable(vreg->reg);
+
+ if (!ret) {
+ /* ignore errors on applying disable config */
+ ufs_qcom_phy_cfg_vreg(phy, vreg, false);
+ vreg->enabled = false;
+ } else {
+ dev_err(dev, "%s: %s disable failed, err=%d\n",
+ __func__, vreg->name, ret);
+ }
+out:
+ return ret;
+}
+
+void ufs_qcom_phy_disable_ref_clk(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ if (phy->is_ref_clk_enabled) {
+ clk_disable_unprepare(phy->ref_clk);
+ /*
+ * "ref_clk_parent" is optional clock hence make sure that clk
+ * reference is available before trying to disable the clock.
+ */
+ if (phy->ref_clk_parent)
+ clk_disable_unprepare(phy->ref_clk_parent);
+ clk_disable_unprepare(phy->ref_clk_src);
+ phy->is_ref_clk_enabled = false;
+ }
+}
+
+#define UFS_REF_CLK_EN (1 << 5)
+
+static void ufs_qcom_phy_dev_ref_clk_ctrl(struct phy *generic_phy, bool enable)
+{
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ if (phy->dev_ref_clk_ctrl_mmio &&
+ (enable ^ phy->is_dev_ref_clk_enabled)) {
+ u32 temp = readl_relaxed(phy->dev_ref_clk_ctrl_mmio);
+
+ if (enable)
+ temp |= UFS_REF_CLK_EN;
+ else
+ temp &= ~UFS_REF_CLK_EN;
+
+ writel_relaxed(temp, phy->dev_ref_clk_ctrl_mmio);
+ /* ensure that ref_clk is enabled/disabled before we return */
+ wmb();
+ phy->is_dev_ref_clk_enabled = enable;
+ }
+}
+
+void ufs_qcom_phy_enable_dev_ref_clk(struct phy *generic_phy)
+{
+ ufs_qcom_phy_dev_ref_clk_ctrl(generic_phy, true);
+}
+
+void ufs_qcom_phy_disable_dev_ref_clk(struct phy *generic_phy)
+{
+ ufs_qcom_phy_dev_ref_clk_ctrl(generic_phy, false);
+}
+
+void ufs_qcom_phy_restore_swi_regs(struct phy *generic_phy)
+{
+ int i;
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ for (i = 0; i < phy->cached_regs_table_size; i++) {
+ struct ufs_qcom_phy_calibration *table =
+ (struct ufs_qcom_phy_calibration *)phy->cached_regs;
+ writel_relaxed(table[i].cfg_value, phy->mmio +
+ table[i].reg_offset);
+ }
+
+ /* flush buffered writes */
+ mb();
+}
+
+/* Turn ON M-PHY RMMI interface clocks */
+int ufs_qcom_phy_enable_iface_clk(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (phy->is_iface_clk_enabled)
+ goto out;
+
+ ret = clk_prepare_enable(phy->tx_iface_clk);
+ if (ret) {
+ dev_err(phy->dev, "%s: tx_iface_clk enable failed %d\n",
+ __func__, ret);
+ goto out;
+ }
+ ret = clk_prepare_enable(phy->rx_iface_clk);
+ if (ret) {
+ clk_disable_unprepare(phy->tx_iface_clk);
+ dev_err(phy->dev, "%s: rx_iface_clk enable failed %d. disabling also tx_iface_clk\n",
+ __func__, ret);
+ goto out;
+ }
+ phy->is_iface_clk_enabled = true;
+
+out:
+ return ret;
+}
+
+/* Turn OFF M-PHY RMMI interface clocks */
+void ufs_qcom_phy_disable_iface_clk(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ if (phy->is_iface_clk_enabled) {
+ clk_disable_unprepare(phy->tx_iface_clk);
+ clk_disable_unprepare(phy->rx_iface_clk);
+ phy->is_iface_clk_enabled = false;
+ }
+}
+
+int ufs_qcom_phy_is_cfg_restore_quirk_enabled(struct phy *phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy);
+
+ return ufs_qcom_phy->quirks & UFS_QCOM_PHY_QUIRK_CFG_RESTORE;
+}
+
+int ufs_qcom_phy_start_serdes(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->start_serdes) {
+ dev_err(ufs_qcom_phy->dev, "%s: start_serdes() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->start_serdes(ufs_qcom_phy);
+ }
+
+ return ret;
+}
+
+int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable) {
+ dev_err(ufs_qcom_phy->dev, "%s: set_tx_lane_enable() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable(ufs_qcom_phy,
+ tx_lanes);
+ }
+
+ return ret;
+}
+
+void ufs_qcom_phy_save_controller_version(struct phy *generic_phy,
+ u8 major, u16 minor, u16 step)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+
+ ufs_qcom_phy->host_ctrl_rev_major = major;
+ ufs_qcom_phy->host_ctrl_rev_minor = minor;
+ ufs_qcom_phy->host_ctrl_rev_step = step;
+}
+
+int ufs_qcom_phy_calibrate_phy(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->calibrate_phy) {
+ dev_err(ufs_qcom_phy->dev, "%s: calibrate_phy() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ret = ufs_qcom_phy->phy_spec_ops->
+ calibrate_phy(ufs_qcom_phy);
+ if (ret)
+ dev_err(ufs_qcom_phy->dev, "%s: calibrate_phy() failed %d\n",
+ __func__, ret);
+ }
+
+ return ret;
+}
+
+int ufs_qcom_phy_remove(struct phy *generic_phy,
+ struct ufs_qcom_phy *ufs_qcom_phy)
+{
+ phy_power_off(generic_phy);
+
+ kfree(ufs_qcom_phy->vdda_pll.name);
+ kfree(ufs_qcom_phy->vdda_phy.name);
+
+ return 0;
+}
+
+int ufs_qcom_phy_exit(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+
+ if (ufs_qcom_phy->is_powered_on)
+ phy_power_off(generic_phy);
+
+ return 0;
+}
+
+int ufs_qcom_phy_is_pcs_ready(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+
+ if (!ufs_qcom_phy->phy_spec_ops->is_physical_coding_sublayer_ready) {
+ dev_err(ufs_qcom_phy->dev, "%s: is_physical_coding_sublayer_ready() callback is not supported\n",
+ __func__);
+ return -ENOTSUPP;
+ }
+
+ return ufs_qcom_phy->phy_spec_ops->
+ is_physical_coding_sublayer_ready(ufs_qcom_phy);
+}
+
+int ufs_qcom_phy_save_configuration(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->save_configuration) {
+ dev_err(ufs_qcom_phy->dev, "%s: save_configuration() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->save_configuration(ufs_qcom_phy);
+ }
+
+ return ret;
+}
+
+int ufs_qcom_phy_restore_configuration(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->restore_configuration) {
+ dev_err(ufs_qcom_phy->dev, "%s: restore_configuration() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->restore_configuration(ufs_qcom_phy);
+ }
+
+ return ret;
+}
+
+int ufs_qcom_phy_power_on(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+ struct device *dev = phy_common->dev;
+ int err;
+
+ err = ufs_qcom_phy_enable_vreg(generic_phy, &phy_common->vdda_phy);
+ if (err) {
+ dev_err(dev, "%s enable vdda_phy failed, err=%d\n",
+ __func__, err);
+ goto out;
+ }
+
+ phy_common->phy_spec_ops->power_control(phy_common, true);
+
+ /* vdda_pll also enables ref clock LDOs so enable it first */
+ err = ufs_qcom_phy_enable_vreg(generic_phy, &phy_common->vdda_pll);
+ if (err) {
+ dev_err(dev, "%s enable vdda_pll failed, err=%d\n",
+ __func__, err);
+ goto out_disable_phy;
+ }
+
+ err = ufs_qcom_phy_enable_ref_clk(generic_phy);
+ if (err) {
+ dev_err(dev, "%s enable phy ref clock failed, err=%d\n",
+ __func__, err);
+ goto out_disable_pll;
+ }
+
+ /* enable device PHY ref_clk pad rail */
+ if (phy_common->vddp_ref_clk.reg) {
+ err = ufs_qcom_phy_enable_vreg(generic_phy,
+ &phy_common->vddp_ref_clk);
+ if (err) {
+ dev_err(dev, "%s enable vddp_ref_clk failed, err=%d\n",
+ __func__, err);
+ goto out_disable_ref_clk;
+ }
+ }
+
+ phy_common->is_powered_on = true;
+ goto out;
+
+out_disable_ref_clk:
+ ufs_qcom_phy_disable_ref_clk(generic_phy);
+out_disable_pll:
+ ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_pll);
+out_disable_phy:
+ ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_phy);
+out:
+ return err;
+}
+
+int ufs_qcom_phy_power_off(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+
+ phy_common->phy_spec_ops->power_control(phy_common, false);
+
+ if (phy_common->vddp_ref_clk.reg)
+ ufs_qcom_phy_disable_vreg(generic_phy,
+ &phy_common->vddp_ref_clk);
+ ufs_qcom_phy_disable_ref_clk(generic_phy);
+
+ ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_pll);
+ ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_phy);
+ phy_common->is_powered_on = false;
+
+ return 0;
+}
diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig
index 6e07b2a..509cf55 100644
--- a/drivers/scsi/ufs/Kconfig
+++ b/drivers/scsi/ufs/Kconfig
@@ -70,3 +70,27 @@ config SCSI_UFSHCD_PLATFORM
If you have a controller with this interface, say Y or M here.
If unsure, say N.
+
+config SCSI_UFS_QCOM
+ bool "QCOM specific hooks to UFS controller platform driver"
+ depends on SCSI_UFSHCD_PLATFORM && ARCH_MSM
+ help
+ This selects the QCOM specific additions to UFSHCD platform driver.
+ UFS host on QCOM needs some vendor specific configuration before
+ accessing the hardware which includes PHY configuration and vendor
+ specific registers.
+
+ Select this if you have UFS controller on QCOM chipset.
+ If unsure, say N.
+
+config SCSI_UFS_QCOM_ICE
+ bool "QCOM specific hooks to Inline Crypto Engine for UFS driver"
+ depends on SCSI_UFS_QCOM && CRYPTO_DEV_QCOM_ICE
+ help
+ This selects the QCOM specific additions to support Inline Crypto
+ Engine (ICE).
+ ICE accelerates the crypto operations and maintains the high UFS
+ performance.
+
+ Select this if you have ICE supported for UFS on QCOM chipset.
+ If unsure, say N.
\ No newline at end of file
diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile
index 1e5bd48..31adca5 100644
--- a/drivers/scsi/ufs/Makefile
+++ b/drivers/scsi/ufs/Makefile
@@ -1,4 +1,6 @@
# UFSHCD makefile
+obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
+obj-$(CONFIG_SCSI_UFS_QCOM_ICE) += ufs-qcom-ice.o
obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o
obj-$(CONFIG_SCSI_UFSHCD_PCI) += ufshcd-pci.o
obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o
diff --git a/drivers/scsi/ufs/ufs-qcom-ice.c b/drivers/scsi/ufs/ufs-qcom-ice.c
new file mode 100644
index 0000000..2ade16d
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-qcom-ice.c
@@ -0,0 +1,522 @@
+/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/async.h>
+#include <linux/blkdev.h>
+#include <linux/scsi/ufs/ufshcd.h>
+#include <crypto/ice.h>
+
+#include "ufs-qcom-ice.h"
+
+
+#define UFS_QCOM_CRYPTO_LABEL "ufs-qcom-crypto"
+/* Timeout waiting for ICE initialization, that requires TZ access */
+#define UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS 500
+
+static void ufs_qcom_ice_success_cb(void *host_ctrl,
+ enum ice_event_completion evt)
+{
+ struct ufs_qcom_host *qcom_host = (struct ufs_qcom_host *)host_ctrl;
+
+ if (qcom_host->ice.state == UFS_QCOM_ICE_STATE_DISABLED &&
+ evt == ICE_INIT_COMPLETION)
+ qcom_host->ice.state = UFS_QCOM_ICE_STATE_ACTIVE;
+ else if (qcom_host->ice.state == UFS_QCOM_ICE_STATE_SUSPENDED &&
+ evt == ICE_RESUME_COMPLETION)
+ qcom_host->ice.state = UFS_QCOM_ICE_STATE_ACTIVE;
+
+ complete(&qcom_host->ice.async_done);
+}
+
+static void ufs_qcom_ice_error_cb(void *host_ctrl, enum ice_error_code evt)
+{
+ struct ufs_qcom_host *qcom_host = (struct ufs_qcom_host *)host_ctrl;
+
+ dev_err(qcom_host->hba->dev, "%s: Error in ice operation %d",
+ __func__, evt);
+
+ if (qcom_host->ice.state == UFS_QCOM_ICE_STATE_ACTIVE)
+ qcom_host->ice.state = UFS_QCOM_ICE_STATE_DISABLED;
+
+ complete(&qcom_host->ice.async_done);
+}
+
+static struct platform_device *ufs_qcom_ice_get_pdevice(struct device *ufs_dev)
+{
+ struct device_node *node;
+ struct platform_device *ice_pdev = NULL;
+
+ node = of_parse_phandle(ufs_dev->of_node, UFS_QCOM_CRYPTO_LABEL, 0);
+
+ if (!node) {
+ dev_err(ufs_dev, "%s: ufs-qcom-crypto property not specified\n",
+ __func__);
+ goto out;
+ }
+
+ ice_pdev = qcom_ice_get_pdevice(node);
+out:
+ return ice_pdev;
+}
+
+static
+struct qcom_ice_variant_ops *ufs_qcom_ice_get_vops(struct device *ufs_dev)
+{
+ struct qcom_ice_variant_ops *ice_vops = NULL;
+ struct device_node *node;
+
+ node = of_parse_phandle(ufs_dev->of_node, UFS_QCOM_CRYPTO_LABEL, 0);
+
+ if (!node) {
+ dev_err(ufs_dev, "%s: ufs-qcom-crypto property not specified\n",
+ __func__);
+ goto out;
+ }
+
+ ice_vops = qcom_ice_get_variant_ops(node);
+
+ if (!ice_vops)
+ dev_err(ufs_dev, "%s: invalid ice_vops\n", __func__);
+
+ of_node_put(node);
+out:
+ return ice_vops;
+}
+
+/**
+ * ufs_qcom_ice_get_dev() - sets pointers to ICE data structs in UFS QCom host
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ *
+ * Sets ICE platform device pointer and ICE vops structure
+ * corresponding to the current UFS device.
+ *
+ * Return: -EINVAL in-case of invalid input parameters:
+ * qcom_host, qcom_host->hba or qcom_host->hba->dev
+ * -ENODEV in-case ICE device is not required
+ * -EPROBE_DEFER in-case ICE is required and hasn't been probed yet
+ * 0 otherwise
+ */
+int ufs_qcom_ice_get_dev(struct ufs_qcom_host *qcom_host)
+{
+ struct device *ufs_dev;
+ int err = 0;
+
+ if (!qcom_host || !qcom_host->hba || !qcom_host->hba->dev) {
+ pr_err("%s: invalid qcom_host %p or qcom_host->hba or qcom_host->hba->dev\n",
+ __func__, qcom_host);
+ err = -EINVAL;
+ goto out;
+ }
+
+ ufs_dev = qcom_host->hba->dev;
+
+ qcom_host->ice.vops = ufs_qcom_ice_get_vops(ufs_dev);
+ qcom_host->ice.pdev = ufs_qcom_ice_get_pdevice(ufs_dev);
+
+ if (qcom_host->ice.pdev == ERR_PTR(-EPROBE_DEFER)) {
+ dev_err(ufs_dev, "%s: ICE device not probed yet\n",
+ __func__);
+ qcom_host->ice.pdev = NULL;
+ qcom_host->ice.vops = NULL;
+ err = -EPROBE_DEFER;
+ goto out;
+ }
+
+ if (!qcom_host->ice.pdev || !qcom_host->ice.vops) {
+ dev_err(ufs_dev, "%s: invalid platform device %p or vops %p\n",
+ __func__, qcom_host->ice.pdev, qcom_host->ice.vops);
+ qcom_host->ice.pdev = NULL;
+ qcom_host->ice.vops = NULL;
+ err = -ENODEV;
+ goto out;
+ }
+
+ qcom_host->ice.state = UFS_QCOM_ICE_STATE_DISABLED;
+
+out:
+ return err;
+
+}
+
+/**
+ * ufs_qcom_ice_init() - initializes the ICE-UFS interface and ICE device
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_init(struct ufs_qcom_host *qcom_host)
+{
+ struct device *ufs_dev = qcom_host->hba->dev;
+ int err = -EINVAL;
+
+ init_completion(&qcom_host->ice.async_done);
+ err = qcom_host->ice.vops->init(qcom_host->ice.pdev,
+ qcom_host,
+ ufs_qcom_ice_success_cb,
+ ufs_qcom_ice_error_cb);
+ if (err) {
+ dev_err(ufs_dev, "%s: ice init failed. err = %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ if (!wait_for_completion_timeout(&qcom_host->ice.async_done,
+ msecs_to_jiffies(UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS))) {
+ dev_err(qcom_host->hba->dev,
+ "%s: error. got timeout after %d ms\n",
+ __func__, UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS);
+ err = -ETIMEDOUT;
+ goto out;
+ }
+
+ if (qcom_host->ice.state != UFS_QCOM_ICE_STATE_ACTIVE) {
+ dev_err(qcom_host->hba->dev,
+ "%s: error. ice.state (%d) is not in active state\n",
+ __func__, qcom_host->ice.state);
+ err = -EINVAL;
+ }
+
+out:
+ return err;
+}
+
+static inline bool ufs_qcom_is_data_cmd(char cmd_op, bool is_write)
+{
+ if (is_write) {
+ if (cmd_op == WRITE_6 || cmd_op == WRITE_10 ||
+ cmd_op == WRITE_16)
+ return true;
+ } else {
+ if (cmd_op == READ_6 || cmd_op == READ_10 ||
+ cmd_op == READ_16)
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * ufs_qcom_ice_cfg() - configures UFS's ICE registers for an ICE transaction
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ * @cmd: Pointer to a valid scsi command. cmd->request should also be
+ * a valid pointer.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_cfg(struct ufs_qcom_host *qcom_host, struct scsi_cmnd *cmd)
+{
+ struct device *dev = qcom_host->hba->dev;
+ int err = 0;
+ struct ice_data_setting ice_set;
+ unsigned int slot = 0;
+ sector_t lba = 0;
+ unsigned int ctrl_info_2_val = 0;
+ unsigned int bypass = 0;
+ struct request *req;
+ char cmd_op;
+
+ if (!qcom_host->ice.pdev || !qcom_host->ice.vops) {
+ dev_dbg(dev, "%s: ice device is not enabled\n", __func__);
+ goto out;
+ }
+
+ if (qcom_host->ice.state != UFS_QCOM_ICE_STATE_ACTIVE) {
+ dev_err(dev, "%s: ice state (%d) is not active\n",
+ __func__, qcom_host->ice.state);
+ return -EINVAL;
+ }
+
+ req = cmd->request;
+ if (req->bio)
+ lba = req->bio->bi_sector;
+
+ slot = req->tag;
+ if (slot < 0 || slot > qcom_host->hba->nutrs) {
+ dev_err(dev, "%s: slot (%d) is out of boundaries (0...%d)\n",
+ __func__, slot, qcom_host->hba->nutrs);
+ return -EINVAL;
+ }
+
+ memset(&ice_set, sizeof(ice_set), 0);
+ if (qcom_host->ice.vops->config) {
+ err = qcom_host->ice.vops->config(qcom_host->ice.pdev,
+ req, &ice_set);
+
+ if (err) {
+ dev_err(dev, "%s: error in ice_vops->config %d\n",
+ __func__, err);
+ goto out;
+ }
+ }
+
+ cmd_op = cmd->cmnd[0];
+
+#define UFS_QCOM_DIR_WRITE true
+#define UFS_QCOM_DIR_READ false
+ /* if non data command, bypass shall be enabled */
+ if (!ufs_qcom_is_data_cmd(cmd_op, UFS_QCOM_DIR_WRITE) &&
+ !ufs_qcom_is_data_cmd(cmd_op, UFS_QCOM_DIR_READ))
+ bypass = UFS_QCOM_ICE_ENABLE_BYPASS;
+ /* if writing data command */
+ else if (ufs_qcom_is_data_cmd(cmd_op, UFS_QCOM_DIR_WRITE))
+ bypass = ice_set.encr_bypass ? UFS_QCOM_ICE_ENABLE_BYPASS :
+ UFS_QCOM_ICE_DISABLE_BYPASS;
+ /* if reading data command */
+ else if (ufs_qcom_is_data_cmd(cmd_op, UFS_QCOM_DIR_READ))
+ bypass = ice_set.decr_bypass ? UFS_QCOM_ICE_ENABLE_BYPASS :
+ UFS_QCOM_ICE_DISABLE_BYPASS;
+
+ /* Configure ICE index */
+ ctrl_info_2_val =
+ (ice_set.crypto_data.key_index &
+ MASK_UFS_QCOM_ICE_CTRL_INFO_2_KEY_INDEX)
+ << OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_KEY_INDEX;
+
+ /* Configure data unit size of transfer request */
+ ctrl_info_2_val |=
+ (UFS_QCOM_ICE_TR_DATA_UNIT_4_KB &
+ MASK_UFS_QCOM_ICE_CTRL_INFO_2_CDU)
+ << OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_CDU;
+
+ /* Configure ICE bypass mode */
+ ctrl_info_2_val |=
+ (bypass & MASK_UFS_QCOM_ICE_CTRL_INFO_2_BYPASS)
+ << OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_BYPASS;
+
+ ufshcd_writel(qcom_host->hba, lba,
+ (REG_UFS_QCOM_ICE_CTRL_INFO_1_n + 8 * slot));
+
+ ufshcd_writel(qcom_host->hba, ctrl_info_2_val,
+ (REG_UFS_QCOM_ICE_CTRL_INFO_2_n + 8 * slot));
+
+ /*
+ * Ensure UFS-ICE registers are being configured
+ * before next operation, otherwise UFS Host Controller might
+ * set get errors
+ */
+ mb();
+out:
+ return err;
+}
+
+/**
+ * ufs_qcom_ice_reset() - resets UFS-ICE interface and ICE device
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_reset(struct ufs_qcom_host *qcom_host)
+{
+ struct device *dev = qcom_host->hba->dev;
+ int err = 0;
+
+ if (!qcom_host->ice.pdev) {
+ dev_dbg(dev, "%s: ice device is not enabled\n", __func__);
+ goto out;
+ }
+
+ if (!qcom_host->ice.vops) {
+ dev_err(dev, "%s: invalid ice_vops\n", __func__);
+ return -EINVAL;
+ }
+
+ if (qcom_host->ice.state != UFS_QCOM_ICE_STATE_ACTIVE)
+ goto out;
+
+ init_completion(&qcom_host->ice.async_done);
+
+ if (qcom_host->ice.vops->reset) {
+ err = qcom_host->ice.vops->reset(qcom_host->ice.pdev);
+ if (err) {
+ dev_err(dev, "%s: ice_vops->reset failed. err %d\n",
+ __func__, err);
+ goto out;
+ }
+ }
+
+ if (!wait_for_completion_timeout(&qcom_host->ice.async_done,
+ msecs_to_jiffies(UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS))) {
+ dev_err(dev,
+ "%s: error. got timeout after %d ms\n",
+ __func__, UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS);
+ err = -ETIMEDOUT;
+ }
+
+out:
+ return err;
+}
+
+/**
+ * ufs_qcom_ice_resume() - resumes UFS-ICE interface and ICE device from power
+ * collapse
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_resume(struct ufs_qcom_host *qcom_host)
+{
+ struct device *dev = qcom_host->hba->dev;
+ int err = 0;
+
+ if (!qcom_host->ice.pdev) {
+ dev_dbg(dev, "%s: ice device is not enabled\n", __func__);
+ goto out;
+ }
+
+ if (qcom_host->ice.state !=
+ UFS_QCOM_ICE_STATE_SUSPENDED) {
+ goto out;
+ }
+
+ if (!qcom_host->ice.vops) {
+ dev_err(dev, "%s: invalid ice_vops\n", __func__);
+ return -EINVAL;
+ }
+
+ init_completion(&qcom_host->ice.async_done);
+
+ if (qcom_host->ice.vops->resume) {
+ err = qcom_host->ice.vops->resume(qcom_host->ice.pdev);
+ if (err) {
+ dev_err(dev, "%s: ice_vops->resume failed. err %d\n",
+ __func__, err);
+ return -EINVAL;
+ }
+ }
+
+ if (!wait_for_completion_timeout(&qcom_host->ice.async_done,
+ msecs_to_jiffies(UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS))) {
+ dev_err(dev,
+ "%s: error. got timeout after %d ms\n",
+ __func__, UFS_QCOM_ICE_COMPLETION_TIMEOUT_MS);
+ err = -ETIMEDOUT;
+ goto out;
+ }
+
+ if (qcom_host->ice.state != UFS_QCOM_ICE_STATE_ACTIVE)
+ err = -EINVAL;
+out:
+ return err;
+}
+
+/**
+ * ufs_qcom_ice_suspend() - suspends UFS-ICE interface and ICE device
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_suspend(struct ufs_qcom_host *qcom_host)
+{
+ struct device *dev = qcom_host->hba->dev;
+ int err = 0;
+
+ if (!qcom_host->ice.pdev) {
+ dev_dbg(dev, "%s: ice device is not enabled\n", __func__);
+ goto out;
+ }
+
+ if (qcom_host->ice.vops->suspend) {
+ err = qcom_host->ice.vops->suspend(qcom_host->ice.pdev);
+ if (err) {
+ dev_err(qcom_host->hba->dev,
+ "%s: ice_vops->suspend failed. err %d\n",
+ __func__, err);
+ return -EINVAL;
+ }
+ }
+
+ if (qcom_host->ice.state == UFS_QCOM_ICE_STATE_ACTIVE) {
+ qcom_host->ice.state = UFS_QCOM_ICE_STATE_SUSPENDED;
+ } else if (qcom_host->ice.state == UFS_QCOM_ICE_STATE_DISABLED) {
+ dev_err(qcom_host->hba->dev,
+ "%s: ice state is invalid: disabled\n",
+ __func__);
+ err = -EINVAL;
+ }
+
+out:
+ return err;
+}
+
+/**
+ * ufs_qcom_ice_get_status() - returns the status of an ICE transaction
+ * @qcom_host: Pointer to a UFS QCom internal host structure.
+ * qcom_host, qcom_host->hba and qcom_host->hba->dev should all
+ * be valid pointers.
+ * @ice_status: Pointer to a valid output parameter.
+ * < 0 in case of ICE transaction failure.
+ * 0 otherwise.
+ *
+ * Return: -EINVAL in-case of an error
+ * 0 otherwise
+ */
+int ufs_qcom_ice_get_status(struct ufs_qcom_host *qcom_host, int *ice_status)
+{
+ struct device *dev = NULL;
+ int err = 0;
+ int stat = -EINVAL;
+
+ ice_status = 0;
+
+ dev = qcom_host->hba->dev;
+ if (!dev) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ if (!qcom_host->ice.pdev) {
+ dev_dbg(dev, "%s: ice device is not enabled\n", __func__);
+ goto out;
+ }
+
+ if (qcom_host->ice.state != UFS_QCOM_ICE_STATE_ACTIVE) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ if (!qcom_host->ice.vops) {
+ dev_err(dev, "%s: invalid ice_vops\n", __func__);
+ return -EINVAL;
+ }
+
+ if (qcom_host->ice.vops->status) {
+ stat = qcom_host->ice.vops->status(qcom_host->ice.pdev);
+ if (stat < 0) {
+ dev_err(dev, "%s: ice_vops->status failed. stat %d\n",
+ __func__, stat);
+ err = -EINVAL;
+ goto out;
+ }
+
+ *ice_status = stat;
+ }
+
+out:
+ return err;
+}
diff --git a/drivers/scsi/ufs/ufs-qcom-ice.h b/drivers/scsi/ufs/ufs-qcom-ice.h
new file mode 100644
index 0000000..1ed8e92
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-qcom-ice.h
@@ -0,0 +1,113 @@
+/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _UFS_QCOM_ICE_H_
+#define _UFS_QCOM_ICE_H_
+
+#include <scsi/scsi_cmnd.h>
+
+#include <linux/scsi/ufs/ufs-qcom.h>
+
+/*
+ * UFS host controller ICE registers. There are n [0..31]
+ * of each of these registers
+ */
+enum {
+ REG_UFS_QCOM_ICE_CTRL_INFO_1_n = 0x2204,
+ REG_UFS_QCOM_ICE_CTRL_INFO_2_n = 0x2208,
+};
+
+/* UFS QCOM ICE CTRL Info 2 register offset */
+enum {
+ OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_BYPASS = 0,
+ OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_KEY_INDEX = 0x1,
+ OFFSET_UFS_QCOM_ICE_CTRL_INFO_2_CDU = 0x6,
+};
+
+/* UFS QCOM ICE CTRL Info 2 register masks */
+enum {
+ MASK_UFS_QCOM_ICE_CTRL_INFO_2_BYPASS = 0x1,
+ MASK_UFS_QCOM_ICE_CTRL_INFO_2_KEY_INDEX = 0x1F,
+ MASK_UFS_QCOM_ICE_CTRL_INFO_2_CDU = 0x8,
+};
+
+/* UFS QCOM ICE encryption/decryption bypass state */
+enum {
+ UFS_QCOM_ICE_DISABLE_BYPASS = 0,
+ UFS_QCOM_ICE_ENABLE_BYPASS = 1,
+};
+
+/* UFS QCOM ICE Crypto Data Unit of target DUN of Transfer Request */
+enum {
+ UFS_QCOM_ICE_TR_DATA_UNIT_512_B = 0,
+ UFS_QCOM_ICE_TR_DATA_UNIT_1_KB = 1,
+ UFS_QCOM_ICE_TR_DATA_UNIT_2_KB = 2,
+ UFS_QCOM_ICE_TR_DATA_UNIT_4_KB = 3,
+ UFS_QCOM_ICE_TR_DATA_UNIT_8_KB = 4,
+ UFS_QCOM_ICE_TR_DATA_UNIT_16_KB = 5,
+ UFS_QCOM_ICE_TR_DATA_UNIT_32_KB = 6,
+};
+
+/* UFS QCOM ICE internal state */
+enum {
+ UFS_QCOM_ICE_STATE_DISABLED = 0,
+ UFS_QCOM_ICE_STATE_ACTIVE = 1,
+ UFS_QCOM_ICE_STATE_SUSPENDED = 2,
+};
+
+#ifdef CONFIG_SCSI_UFS_QCOM_ICE
+int ufs_qcom_ice_get_dev(struct ufs_qcom_host *qcom_host);
+int ufs_qcom_ice_init(struct ufs_qcom_host *qcom_host);
+int ufs_qcom_ice_cfg(struct ufs_qcom_host *qcom_host, struct scsi_cmnd *cmd);
+int ufs_qcom_ice_reset(struct ufs_qcom_host *qcom_host);
+int ufs_qcom_ice_resume(struct ufs_qcom_host *qcom_host);
+int ufs_qcom_ice_suspend(struct ufs_qcom_host *qcom_host);
+int ufs_qcom_ice_get_status(struct ufs_qcom_host *qcom_host, int *ice_status);
+#else
+inline int ufs_qcom_ice_get_dev(struct ufs_qcom_host *qcom_host)
+{
+ if (qcom_host) {
+ qcom_host->ice.pdev = NULL;
+ qcom_host->ice.vops = NULL;
+ }
+ return -ENODEV;
+}
+inline int ufs_qcom_ice_init(struct ufs_qcom_host *qcom_host)
+{
+ return 0;
+}
+inline int ufs_qcom_ice_cfg(struct ufs_qcom_host *qcom_host,
+ struct scsi_cmnd *cmd)
+{
+ return 0;
+}
+inline int ufs_qcom_ice_reset(struct ufs_qcom_host *qcom_host)
+{
+ return 0;
+}
+inline int ufs_qcom_ice_resume(struct ufs_qcom_host *qcom_host)
+{
+ return 0;
+}
+inline int ufs_qcom_ice_suspend(struct ufs_qcom_host *qcom_host)
+{
+ return 0;
+}
+inline int ufs_qcom_ice_get_status(struct ufs_qcom_host *qcom_host,
+ int *ice_status)
+{
+ return 0;
+}
+#endif /* CONFIG_SCSI_UFS_QCOM_ICE */
+
+#endif /* UFS_QCOM_ICE_H_ */
diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
new file mode 100644
index 0000000..101aecc
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -0,0 +1,1204 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <linux/phy/phy.h>
+
+#include <linux/scsi/ufs/ufshcd.h>
+#include <linux/scsi/ufs/ufs-qcom.h>
+#include <linux/phy/phy-qcom-ufs.h>
+#include "ufshci.h"
+#include "ufs-qcom-ice.h"
+
+static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS];
+
+static void ufs_qcom_get_speed_mode(struct ufs_pa_layer_attr *p, char *result);
+static int ufs_qcom_get_bus_vote(struct ufs_qcom_host *host,
+ const char *speed_mode);
+static int ufs_qcom_set_bus_vote(struct ufs_qcom_host *host, int vote);
+static int ufs_qcom_update_sec_cfg(struct ufs_hba *hba, bool restore_sec_cfg);
+
+static int ufs_qcom_get_connected_tx_lanes(struct ufs_hba *hba, u32 *tx_lanes)
+{
+ int err = 0;
+
+ err = ufshcd_dme_get(hba,
+ UIC_ARG_MIB(PA_CONNECTEDTXDATALANES), tx_lanes);
+ if (err)
+ dev_err(hba->dev, "%s: couldn't read PA_CONNECTEDTXDATALANES %d\n",
+ __func__, err);
+
+ return err;
+}
+
+static int ufs_qcom_host_clk_get(struct device *dev,
+ const char *name, struct clk **clk_out)
+{
+ struct clk *clk;
+ int err = 0;
+
+ clk = devm_clk_get(dev, name);
+ if (IS_ERR(clk)) {
+ err = PTR_ERR(clk);
+ dev_err(dev, "%s: failed to get %s err %d",
+ __func__, name, err);
+ } else {
+ *clk_out = clk;
+ }
+
+ return err;
+}
+
+static int ufs_qcom_host_clk_enable(struct device *dev,
+ const char *name, struct clk *clk)
+{
+ int err = 0;
+
+ err = clk_prepare_enable(clk);
+ if (err)
+ dev_err(dev, "%s: %s enable failed %d\n", __func__, name, err);
+
+ return err;
+}
+
+static void ufs_qcom_disable_lane_clks(struct ufs_qcom_host *host)
+{
+ if (!host->is_lane_clks_enabled)
+ return;
+
+ clk_disable_unprepare(host->tx_l1_sync_clk);
+ clk_disable_unprepare(host->tx_l0_sync_clk);
+ clk_disable_unprepare(host->rx_l1_sync_clk);
+ clk_disable_unprepare(host->rx_l0_sync_clk);
+
+ host->is_lane_clks_enabled = false;
+}
+
+static int ufs_qcom_enable_lane_clks(struct ufs_qcom_host *host)
+{
+ int err = 0;
+ struct device *dev = host->hba->dev;
+
+ if (host->is_lane_clks_enabled)
+ return 0;
+
+ err = ufs_qcom_host_clk_enable(dev, "rx_lane0_sync_clk",
+ host->rx_l0_sync_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_host_clk_enable(dev, "tx_lane0_sync_clk",
+ host->tx_l0_sync_clk);
+ if (err)
+ goto disable_rx_l0;
+
+ if (host->lanes_per_direction > 1) {
+ err = ufs_qcom_host_clk_enable(dev, "rx_lane1_sync_clk",
+ host->rx_l1_sync_clk);
+ if (err)
+ goto disable_tx_l0;
+
+ err = ufs_qcom_host_clk_enable(dev, "tx_lane1_sync_clk",
+ host->tx_l1_sync_clk);
+ if (err)
+ goto disable_rx_l1;
+ }
+ host->is_lane_clks_enabled = true;
+ goto out;
+
+disable_rx_l1:
+ clk_disable_unprepare(host->rx_l1_sync_clk);
+disable_tx_l0:
+ clk_disable_unprepare(host->tx_l0_sync_clk);
+disable_rx_l0:
+ clk_disable_unprepare(host->rx_l0_sync_clk);
+out:
+ return err;
+}
+
+static int ufs_qcom_init_lanes(struct ufs_qcom_host *host)
+{
+ int err = 0;
+ struct device *dev = host->hba->dev;
+ struct device_node *np = dev->of_node;
+
+ err = of_property_read_u32(np, "qcom,lanes-per-direction",
+ &host->lanes_per_direction);
+ if (err) {
+ dev_err(dev,
+ "%s: failed to read lanes-per-direction, err=%d\n",
+ __func__, err);
+ return err;
+ }
+ printk("%s: lanes-per-direction = %u\n", __func__, host->lanes_per_direction);
+
+ err = ufs_qcom_host_clk_get(dev,
+ "rx_lane0_sync_clk", &host->rx_l0_sync_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_host_clk_get(dev,
+ "tx_lane0_sync_clk", &host->tx_l0_sync_clk);
+ if (err)
+ goto out;
+
+ /* in case of single lane per direction, don't read lane1 clocks */
+ if (host->lanes_per_direction > 1) {
+ err = ufs_qcom_host_clk_get(dev, "rx_lane1_sync_clk",
+ &host->rx_l1_sync_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_host_clk_get(dev, "tx_lane1_sync_clk",
+ &host->tx_l1_sync_clk);
+ }
+out:
+ return err;
+}
+
+static int ufs_qcom_link_startup_post_change(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+ u32 tx_lanes;
+ int err = 0;
+
+ err = ufs_qcom_get_connected_tx_lanes(hba, &tx_lanes);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_set_tx_lane_enable(phy, tx_lanes);
+ if (err)
+ dev_err(hba->dev, "%s: ufs_qcom_phy_set_tx_lane_enable failed\n",
+ __func__);
+
+out:
+ return err;
+}
+
+static int ufs_qcom_check_hibern8(struct ufs_hba *hba)
+{
+ int err;
+ u32 tx_fsm_val = 0;
+ unsigned long timeout = jiffies + msecs_to_jiffies(HBRN8_POLL_TOUT_MS);
+
+ do {
+ err = ufshcd_dme_get(hba,
+ UIC_ARG_MIB(MPHY_TX_FSM_STATE), &tx_fsm_val);
+ if (err || tx_fsm_val == TX_FSM_HIBERN8)
+ break;
+
+ /* sleep for max. 200us */
+ usleep_range(100, 200);
+ } while (time_before(jiffies, timeout));
+
+ /*
+ * we might have scheduled out for long during polling so
+ * check the state again.
+ */
+ if (time_after(jiffies, timeout))
+ err = ufshcd_dme_get(hba,
+ UIC_ARG_MIB(MPHY_TX_FSM_STATE), &tx_fsm_val);
+
+ if (err) {
+ dev_err(hba->dev, "%s: unable to get TX_FSM_STATE, err %d\n",
+ __func__, err);
+ } else if (tx_fsm_val != TX_FSM_HIBERN8) {
+ err = tx_fsm_val;
+ dev_err(hba->dev, "%s: invalid TX_FSM_STATE = %d\n",
+ __func__, err);
+ }
+
+ return err;
+}
+
+static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+ int ret = 0;
+ u8 major;
+ u16 minor, step;
+
+ /* Assert PHY reset and apply PHY calibration values */
+ ufs_qcom_assert_reset(hba);
+ /* provide 1ms delay to let the reset pulse propagate */
+ usleep_range(1000, 1100);
+
+ ufs_qcom_get_controller_revision(hba, &major, &minor, &step);
+ ufs_qcom_phy_save_controller_version(phy, major, minor, step);
+ ret = ufs_qcom_phy_calibrate_phy(phy);
+ if (ret) {
+ dev_err(hba->dev, "%s: ufs_qcom_phy_calibrate_phy() failed, ret = %d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ /* De-assert PHY reset and start serdes */
+ ufs_qcom_deassert_reset(hba);
+
+ /*
+ * after reset deassertion, phy will need all ref clocks,
+ * voltage, current to settle down before starting serdes.
+ */
+ usleep_range(1000, 1100);
+ ret = ufs_qcom_phy_start_serdes(phy);
+ if (ret) {
+ dev_err(hba->dev, "%s: ufs_qcom_phy_start_serdes() failed, ret = %d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ ret = ufs_qcom_phy_is_pcs_ready(phy);
+ if (ret)
+ dev_err(hba->dev, "%s: is_physical_coding_sublayer_ready() failed, ret = %d\n",
+ __func__, ret);
+
+out:
+ return ret;
+}
+
+/*
+ * The UTP controller has a number of internal clock gating cells (CGCs).
+ * Internal hardware sub-modules within the UTP controller control the CGCs.
+ * Hardware CGCs disable the clock to inactivate UTP sub-modules not involved
+ * in a specific operation, UTP controller CGCs are by default disabled and
+ * this function enables them (after every UFS link startup) to save some power
+ * leakage.
+ */
+static void ufs_qcom_enable_hw_clk_gating(struct ufs_hba *hba)
+{
+ ufshcd_writel(hba,
+ ufshcd_readl(hba, REG_UFS_CFG2) | REG_UFS_CFG2_CGC_EN_ALL,
+ REG_UFS_CFG2);
+
+ /* Ensure that HW clock gating is enabled before next operations */
+ mb();
+}
+
+static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba, bool status)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ int err = 0;
+
+ switch (status) {
+ case PRE_CHANGE:
+ ufs_qcom_power_up_sequence(hba);
+ /*
+ * The PHY PLL output is the source of tx/rx lane symbol
+ * clocks, hence, enable the lane clocks only after PHY
+ * is initialized.
+ */
+ err = ufs_qcom_enable_lane_clks(host);
+ break;
+ case POST_CHANGE:
+ /* check if UFS PHY moved from DISABLED to HIBERN8 */
+ err = ufs_qcom_check_hibern8(hba);
+ ufs_qcom_enable_hw_clk_gating(hba);
+ if (!err) {
+ err = ufs_qcom_ice_reset(host);
+ if (err)
+ dev_err(hba->dev,
+ "%s: ufs_qcom_ice_reset() failed %d\n",
+ __func__, err);
+ }
+
+ break;
+ default:
+ dev_err(hba->dev, "%s: invalid status %d\n", __func__, status);
+ err = -EINVAL;
+ break;
+ }
+ return err;
+}
+
+/**
+ * Returns non-zero for success (which rate of core_clk) and 0
+ * in case of a failure
+ */
+static unsigned long
+ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, u32 hs, u32 rate)
+{
+ struct ufs_clk_info *clki;
+ u32 core_clk_period_in_ns;
+ u32 tx_clk_cycles_per_us = 0;
+ unsigned long core_clk_rate = 0;
+ u32 core_clk_cycles_per_us = 0;
+
+ static u32 pwm_fr_table[][2] = {
+ {UFS_PWM_G1, 0x1},
+ {UFS_PWM_G2, 0x1},
+ {UFS_PWM_G3, 0x1},
+ {UFS_PWM_G4, 0x1},
+ };
+
+ static u32 hs_fr_table_rA[][2] = {
+ {UFS_HS_G1, 0x1F},
+ {UFS_HS_G2, 0x3e},
+ };
+
+ static u32 hs_fr_table_rB[][2] = {
+ {UFS_HS_G1, 0x24},
+ {UFS_HS_G2, 0x49},
+ };
+
+ if (gear == 0) {
+ dev_err(hba->dev, "%s: invalid gear = %d\n", __func__, gear);
+ goto out_error;
+ }
+
+ list_for_each_entry(clki, &hba->clk_list_head, list) {
+ if (!strcmp(clki->name, "core_clk"))
+ core_clk_rate = clk_get_rate(clki->clk);
+ }
+
+ /* If frequency is smaller than 1MHz, set to 1MHz */
+ if (core_clk_rate < DEFAULT_CLK_RATE_HZ)
+ core_clk_rate = DEFAULT_CLK_RATE_HZ;
+
+ core_clk_cycles_per_us = core_clk_rate / USEC_PER_SEC;
+ ufshcd_writel(hba, core_clk_cycles_per_us, REG_UFS_SYS1CLK_1US);
+
+ core_clk_period_in_ns = NSEC_PER_SEC / core_clk_rate;
+ core_clk_period_in_ns <<= OFFSET_CLK_NS_REG;
+ core_clk_period_in_ns &= MASK_CLK_NS_REG;
+
+ switch (hs) {
+ case FASTAUTO_MODE:
+ case FAST_MODE:
+ if (rate == PA_HS_MODE_A) {
+ if (gear > ARRAY_SIZE(hs_fr_table_rA)) {
+ dev_err(hba->dev,
+ "%s: index %d exceeds table size %zu\n",
+ __func__, gear,
+ ARRAY_SIZE(hs_fr_table_rA));
+ goto out_error;
+ }
+ tx_clk_cycles_per_us = hs_fr_table_rA[gear-1][1];
+ } else if (rate == PA_HS_MODE_B) {
+ if (gear > ARRAY_SIZE(hs_fr_table_rB)) {
+ dev_err(hba->dev,
+ "%s: index %d exceeds table size %zu\n",
+ __func__, gear,
+ ARRAY_SIZE(hs_fr_table_rB));
+ goto out_error;
+ }
+ tx_clk_cycles_per_us = hs_fr_table_rB[gear-1][1];
+ } else {
+ dev_err(hba->dev, "%s: invalid rate = %d\n",
+ __func__, rate);
+ goto out_error;
+ }
+ break;
+ case SLOWAUTO_MODE:
+ case SLOW_MODE:
+ if (gear > ARRAY_SIZE(pwm_fr_table)) {
+ dev_err(hba->dev,
+ "%s: index %d exceeds table size %zu\n",
+ __func__, gear,
+ ARRAY_SIZE(pwm_fr_table));
+ goto out_error;
+ }
+ tx_clk_cycles_per_us = pwm_fr_table[gear-1][1];
+ break;
+ case UNCHANGED:
+ default:
+ dev_err(hba->dev, "%s: invalid mode = %d\n", __func__, hs);
+ goto out_error;
+ }
+
+ /* this register 2 fields shall be written at once */
+ ufshcd_writel(hba, core_clk_period_in_ns | tx_clk_cycles_per_us,
+ REG_UFS_TX_SYMBOL_CLK_NS_US);
+ goto out;
+
+out_error:
+ core_clk_rate = 0;
+out:
+ return core_clk_rate;
+}
+
+static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, bool status)
+{
+ unsigned long core_clk_rate = 0;
+ u32 core_clk_cycles_per_100ms;
+
+ switch (status) {
+ case PRE_CHANGE:
+ core_clk_rate = ufs_qcom_cfg_timers(hba, UFS_PWM_G1,
+ SLOWAUTO_MODE, 0);
+ if (!core_clk_rate) {
+ dev_err(hba->dev, "%s: ufs_qcom_cfg_timers() failed\n",
+ __func__);
+ return -EINVAL;
+ }
+ core_clk_cycles_per_100ms =
+ (core_clk_rate / MSEC_PER_SEC) * 100;
+ ufshcd_writel(hba, core_clk_cycles_per_100ms,
+ REG_UFS_PA_LINK_STARTUP_TIMER);
+ break;
+ case POST_CHANGE:
+ ufs_qcom_link_startup_post_change(hba);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static int ufs_qcom_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+ int ret = 0;
+
+ if (ufs_qcom_is_link_off(hba)) {
+ /*
+ * Disable the tx/rx lane symbol clocks before PHY is
+ * powered down as the PLL source should be disabled
+ * after downstream clocks are disabled.
+ */
+ ufs_qcom_disable_lane_clks(host);
+ phy_power_off(phy);
+ ret = ufs_qcom_ice_suspend(host);
+ if (ret)
+ dev_err(hba->dev, "%s: failed ufs_qcom_ice_suspend %d\n",
+ __func__, ret);
+
+ /* Assert PHY soft reset */
+ ufs_qcom_assert_reset(hba);
+ goto out;
+ }
+
+ /*
+ * If UniPro link is not active, PHY ref_clk, main PHY analog power
+ * rail and low noise analog power rail for PLL can be switched off.
+ */
+ if (!ufs_qcom_is_link_active(hba)) {
+ if (ufs_qcom_phy_is_cfg_restore_quirk_enabled(phy) &&
+ ufs_qcom_is_link_hibern8(hba)) {
+ ret = ufs_qcom_phy_save_configuration(phy);
+ if (ret)
+ dev_err(hba->dev, "%s: failed ufs_qcom_phy_save_configuration %d\n",
+ __func__, ret);
+ }
+ phy_power_off(phy);
+ ufs_qcom_ice_suspend(host);
+ }
+
+out:
+ return ret;
+}
+
+static bool ufs_qcom_is_phy_config_restore_required(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+
+ return ufs_qcom_phy_is_cfg_restore_quirk_enabled(phy)
+ && ufshcd_is_link_hibern8(hba)
+ && hba->is_sys_suspended;
+}
+
+static int ufs_qcom_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+ int err;
+
+ if (ufs_qcom_is_phy_config_restore_required(hba)) {
+ ufs_qcom_assert_reset(hba);
+ /* provide 1ms delay to let the reset pulse propagate */
+ usleep_range(1000, 1100);
+ }
+
+ err = phy_power_on(phy);
+ if (err) {
+ dev_err(hba->dev, "%s: failed enabling regs, err = %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ if (ufs_qcom_is_phy_config_restore_required(hba)) {
+ ufs_qcom_phy_restore_swi_regs(phy);
+
+ /* De-assert PHY reset and start serdes */
+ ufs_qcom_deassert_reset(hba);
+
+ /*
+ * after reset deassertion, phy will need all ref clocks,
+ * voltage, current to settle down before starting serdes.
+ */
+ usleep_range(1000, 1100);
+
+ err = ufs_qcom_phy_start_serdes(phy);
+ if (err) {
+ dev_err(hba->dev, "%s: ufs_qcom_phy_start_serdes() failed, err = %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ err = ufs_qcom_phy_restore_configuration(phy);
+ if (err) {
+ dev_err(hba->dev, "%s: ufs_qcom_phy_restore_configuration() failed, err = %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ err = ufs_qcom_phy_is_pcs_ready(phy);
+ if (err) {
+ dev_err(hba->dev, "%s: is_physical_coding_sublayer_ready() failed, err = %d\n",
+ __func__, err);
+ goto out;
+ }
+ }
+
+ err = ufs_qcom_ice_resume(host);
+ if (err) {
+ dev_err(hba->dev, "%s: ufs_qcom_ice_resume failed, err = %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ hba->is_sys_suspended = false;
+
+out:
+ return err;
+}
+
+static
+int ufs_qcom_crytpo_engine_cfg(struct ufs_hba *hba, unsigned int task_tag)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct ufshcd_lrb *lrbp = &hba->lrb[task_tag];
+ int err = 0;
+
+ if (!host->ice.pdev ||
+ !lrbp->cmd || lrbp->command_type != UTP_CMD_TYPE_SCSI)
+ goto out;
+
+ err = ufs_qcom_ice_cfg(host, lrbp->cmd);
+out:
+ return err;
+}
+
+static int ufs_qcom_crypto_engine_eh(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ int ice_status = 0;
+ int err = 0;
+
+ host->ice.crypto_engine_err = 0;
+
+ if (host->ice.quirks &
+ UFS_QCOM_ICE_QUIRK_HANDLE_CRYPTO_ENGINE_ERRORS) {
+ err = ufs_qcom_ice_get_status(host, &ice_status);
+ if (!err)
+ host->ice.crypto_engine_err = ice_status;
+
+ if (host->ice.crypto_engine_err) {
+ dev_err(hba->dev, "%s handling crypto engine error\n",
+ __func__);
+ /*
+ * block commands from scsi mid-layer.
+ * As crypto error is a fatal error and will result in
+ * a host reset we should leave scsi mid layer blocked
+ * until host reset is completed.
+ * Host reset will be handled in a seperate workqueue
+ * and will be triggered from ufshcd_check_errors.
+ */
+ scsi_block_requests(hba->host);
+
+ ufshcd_abort_outstanding_transfer_requests(hba,
+ DID_TARGET_FAILURE);
+ }
+ }
+
+ return host->ice.crypto_engine_err;
+}
+
+static int ufs_qcom_crypto_engine_get_err(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+
+ return host->ice.crypto_engine_err;
+}
+
+static void ufs_qcom_crypto_engine_reset_err(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+
+ host->ice.crypto_engine_err = 0;
+}
+
+struct ufs_qcom_dev_params {
+ u32 pwm_rx_gear; /* pwm rx gear to work in */
+ u32 pwm_tx_gear; /* pwm tx gear to work in */
+ u32 hs_rx_gear; /* hs rx gear to work in */
+ u32 hs_tx_gear; /* hs tx gear to work in */
+ u32 rx_lanes; /* number of rx lanes */
+ u32 tx_lanes; /* number of tx lanes */
+ u32 rx_pwr_pwm; /* rx pwm working pwr */
+ u32 tx_pwr_pwm; /* tx pwm working pwr */
+ u32 rx_pwr_hs; /* rx hs working pwr */
+ u32 tx_pwr_hs; /* tx hs working pwr */
+ u32 hs_rate; /* rate A/B to work in HS */
+ u32 desired_working_mode;
+};
+
+static int ufs_qcom_get_pwr_dev_param(struct ufs_qcom_dev_params *qcom_param,
+ struct ufs_pa_layer_attr *dev_max,
+ struct ufs_pa_layer_attr *agreed_pwr)
+{
+ int min_qcom_gear;
+ int min_dev_gear;
+ bool is_dev_sup_hs = false;
+ bool is_qcom_max_hs = false;
+
+ if (dev_max->pwr_rx == FAST_MODE)
+ is_dev_sup_hs = true;
+
+ if (qcom_param->desired_working_mode == FAST) {
+ is_qcom_max_hs = true;
+ min_qcom_gear = min_t(u32, qcom_param->hs_rx_gear,
+ qcom_param->hs_tx_gear);
+ } else {
+ min_qcom_gear = min_t(u32, qcom_param->pwm_rx_gear,
+ qcom_param->pwm_tx_gear);
+ }
+
+ /*
+ * device doesn't support HS but qcom_param->desired_working_mode is
+ * HS, thus device and qcom_param don't agree
+ */
+ if (!is_dev_sup_hs && is_qcom_max_hs) {
+ pr_err("%s: failed to agree on power mode (device doesn't support HS but requested power is HS)\n",
+ __func__);
+ return -ENOTSUPP;
+ } else if (is_dev_sup_hs && is_qcom_max_hs) {
+ /*
+ * since device supports HS, it supports FAST_MODE.
+ * since qcom_param->desired_working_mode is also HS
+ * then final decision (FAST/FASTAUTO) is done according
+ * to qcom_params as it is the restricting factor
+ */
+ agreed_pwr->pwr_rx = agreed_pwr->pwr_tx =
+ qcom_param->rx_pwr_hs;
+ } else {
+ /*
+ * here qcom_param->desired_working_mode is PWM.
+ * it doesn't matter whether device supports HS or PWM,
+ * in both cases qcom_param->desired_working_mode will
+ * determine the mode
+ */
+ agreed_pwr->pwr_rx = agreed_pwr->pwr_tx =
+ qcom_param->rx_pwr_pwm;
+ }
+
+ /*
+ * we would like tx to work in the minimum number of lanes
+ * between device capability and vendor preferences.
+ * the same decision will be made for rx
+ */
+ agreed_pwr->lane_tx = min_t(u32, dev_max->lane_tx,
+ qcom_param->tx_lanes);
+ agreed_pwr->lane_rx = min_t(u32, dev_max->lane_rx,
+ qcom_param->rx_lanes);
+
+ /* device maximum gear is the minimum between device rx and tx gears */
+ min_dev_gear = min_t(u32, dev_max->gear_rx, dev_max->gear_tx);
+
+ /*
+ * if both device capabilities and vendor pre-defined preferences are
+ * both HS or both PWM then set the minimum gear to be the chosen
+ * working gear.
+ * if one is PWM and one is HS then the one that is PWM get to decide
+ * what is the gear, as it is the one that also decided previously what
+ * pwr the device will be configured to.
+ */
+ if ((is_dev_sup_hs && is_qcom_max_hs) ||
+ (!is_dev_sup_hs && !is_qcom_max_hs))
+ agreed_pwr->gear_rx = agreed_pwr->gear_tx =
+ min_t(u32, min_dev_gear, min_qcom_gear);
+ else if (!is_dev_sup_hs)
+ agreed_pwr->gear_rx = agreed_pwr->gear_tx = min_dev_gear;
+ else
+ agreed_pwr->gear_rx = agreed_pwr->gear_tx = min_qcom_gear;
+
+ agreed_pwr->hs_rate = qcom_param->hs_rate;
+ return 0;
+}
+
+static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)
+{
+ int vote;
+ int err = 0;
+ char mode[BUS_VECTOR_NAME_LEN];
+
+ ufs_qcom_get_speed_mode(&host->dev_req_params, mode);
+
+ vote = ufs_qcom_get_bus_vote(host, mode);
+ if (vote >= 0)
+ err = ufs_qcom_set_bus_vote(host, vote);
+ else
+ err = vote;
+
+ if (err)
+ dev_err(host->hba->dev, "%s: failed %d\n", __func__, err);
+ else
+ host->bus_vote.saved_vote = vote;
+ return err;
+}
+
+static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
+ bool status,
+ struct ufs_pa_layer_attr *dev_max_params,
+ struct ufs_pa_layer_attr *dev_req_params)
+{
+ u32 val;
+ struct ufs_qcom_host *host = hba->priv;
+ struct phy *phy = host->generic_phy;
+ struct ufs_qcom_dev_params ufs_qcom_cap;
+ int ret = 0;
+ int res = 0;
+
+ if (!dev_req_params) {
+ pr_err("%s: incoming dev_req_params is NULL\n", __func__);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ switch (status) {
+ case PRE_CHANGE:
+ ufs_qcom_cap.tx_lanes = UFS_QCOM_LIMIT_NUM_LANES_TX;
+ ufs_qcom_cap.rx_lanes = UFS_QCOM_LIMIT_NUM_LANES_RX;
+ ufs_qcom_cap.hs_rx_gear = UFS_QCOM_LIMIT_HSGEAR_RX;
+ ufs_qcom_cap.hs_tx_gear = UFS_QCOM_LIMIT_HSGEAR_TX;
+ ufs_qcom_cap.pwm_rx_gear = UFS_QCOM_LIMIT_PWMGEAR_RX;
+ ufs_qcom_cap.pwm_tx_gear = UFS_QCOM_LIMIT_PWMGEAR_TX;
+ ufs_qcom_cap.rx_pwr_pwm = UFS_QCOM_LIMIT_RX_PWR_PWM;
+ ufs_qcom_cap.tx_pwr_pwm = UFS_QCOM_LIMIT_TX_PWR_PWM;
+ ufs_qcom_cap.rx_pwr_hs = UFS_QCOM_LIMIT_RX_PWR_HS;
+ ufs_qcom_cap.tx_pwr_hs = UFS_QCOM_LIMIT_TX_PWR_HS;
+ ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
+ ufs_qcom_cap.desired_working_mode =
+ UFS_QCOM_LIMIT_DESIRED_MODE;
+
+ ret = ufs_qcom_get_pwr_dev_param(&ufs_qcom_cap,
+ dev_max_params,
+ dev_req_params);
+ if (ret) {
+ pr_err("%s: failed to determine capabilities\n",
+ __func__);
+ goto out;
+ }
+
+ break;
+ case POST_CHANGE:
+ if (!ufs_qcom_cfg_timers(hba, dev_req_params->gear_rx,
+ dev_req_params->pwr_rx,
+ dev_req_params->hs_rate)) {
+ dev_err(hba->dev, "%s: ufs_qcom_cfg_timers() failed\n",
+ __func__);
+ /*
+ * we return error code at the end of the routine,
+ * but continue to configure UFS_PHY_TX_LANE_ENABLE
+ * and bus voting as usual
+ */
+ ret = -EINVAL;
+ }
+
+ val = ~(MAX_U32 << dev_req_params->lane_tx);
+ res = ufs_qcom_phy_set_tx_lane_enable(phy, val);
+ if (res) {
+ dev_err(hba->dev, "%s: ufs_qcom_phy_set_tx_lane_enable() failed res = %d\n",
+ __func__, res);
+ ret = res;
+ }
+
+ /* cache the power mode parameters to use internally */
+ memcpy(&host->dev_req_params,
+ dev_req_params, sizeof(*dev_req_params));
+ ufs_qcom_update_bus_bw_vote(host);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+out:
+ return ret;
+}
+
+/**
+ * ufs_qcom_advertise_quirks - advertise the known QCOM UFS controller quirks
+ * @hba: host controller instance
+ *
+ * QCOM UFS host controller might have some non standard behaviours (quirks)
+ * than what is specified by UFSHCI specification. Advertise all such
+ * quirks to standard UFS host controller driver so standard takes them into
+ * account.
+ */
+static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
+{
+ u8 major;
+ u16 minor, step;
+
+ ufs_qcom_get_controller_revision(hba, &major, &minor, &step);
+
+ if (major == 0x1) {
+ hba->quirks |= (UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS
+ | UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP
+ | UFSHCD_QUIRK_BROKEN_LCC
+ | UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE);
+
+ if ((minor == 0x001) && (step == 0x0001))
+ hba->quirks |= UFSHCD_QUIRK_BROKEN_INTR_AGGR;
+ }
+}
+
+static int ufs_qcom_get_bus_vote(struct ufs_qcom_host *host,
+ const char *speed_mode)
+{
+ struct device *dev = host->hba->dev;
+ struct device_node *np = dev->of_node;
+ int err;
+ const char *key = "qcom,bus-vector-names";
+
+ if (!speed_mode) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ if (host->bus_vote.is_max_bw_needed && !!strcmp(speed_mode, "MIN"))
+ err = of_property_match_string(np, key, "MAX");
+ else
+ err = of_property_match_string(np, key, speed_mode);
+
+out:
+ if (err < 0)
+ dev_err(dev, "%s: Invalid %s mode %d\n",
+ __func__, speed_mode, err);
+ return err;
+}
+
+static int ufs_qcom_set_bus_vote(struct ufs_qcom_host *host, int vote)
+{
+ if (vote != host->bus_vote.curr_vote)
+ host->bus_vote.curr_vote = vote;
+
+ return 0;
+}
+
+static void ufs_qcom_get_speed_mode(struct ufs_pa_layer_attr *p, char *result)
+{
+ int gear = max_t(u32, p->gear_rx, p->gear_tx);
+ int lanes = max_t(u32, p->lane_rx, p->lane_tx);
+ int pwr;
+
+ /* default to PWM Gear 1, Lane 1 if power mode is not initialized */
+ if (!gear)
+ gear = 1;
+
+ if (!lanes)
+ lanes = 1;
+
+ if (!p->pwr_rx && !p->pwr_tx) {
+ pwr = SLOWAUTO_MODE;
+ snprintf(result, BUS_VECTOR_NAME_LEN, "MIN");
+ } else if (p->pwr_rx == FAST_MODE || p->pwr_rx == FASTAUTO_MODE ||
+ p->pwr_tx == FAST_MODE || p->pwr_tx == FASTAUTO_MODE) {
+ pwr = FAST_MODE;
+ snprintf(result, BUS_VECTOR_NAME_LEN, "%s_R%s_G%d_L%d", "HS",
+ p->hs_rate == PA_HS_MODE_B ? "B" : "A", gear, lanes);
+ } else {
+ pwr = SLOW_MODE;
+ snprintf(result, BUS_VECTOR_NAME_LEN, "%s_G%d_L%d",
+ "PWM", gear, lanes);
+ }
+}
+
+static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ int err;
+ int vote = 0;
+
+ /*
+ * In case ufs_qcom_init() is not yet done, simply ignore.
+ * This ufs_qcom_setup_clocks() shall be called from
+ * ufs_qcom_init() after init is done.
+ */
+ if (!host)
+ return 0;
+
+ if (on) {
+ err = ufs_qcom_phy_enable_iface_clk(host->generic_phy);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_enable_ref_clk(host->generic_phy);
+ if (err) {
+ dev_err(hba->dev, "%s enable phy ref clock failed, err=%d\n",
+ __func__, err);
+ ufs_qcom_phy_disable_iface_clk(host->generic_phy);
+ goto out;
+ }
+ /* enable the device ref clock */
+ ufs_qcom_phy_enable_dev_ref_clk(host->generic_phy);
+ vote = host->bus_vote.saved_vote;
+ if (vote == host->bus_vote.min_bw_vote)
+ ufs_qcom_update_bus_bw_vote(host);
+ } else {
+ /* M-PHY RMMI interface clocks can be turned off */
+ ufs_qcom_phy_disable_iface_clk(host->generic_phy);
+ if (!ufs_qcom_is_link_active(hba)) {
+ /* turn off UFS local PHY ref_clk */
+ ufs_qcom_phy_disable_ref_clk(host->generic_phy);
+ /* disable device ref_clk */
+ ufs_qcom_phy_disable_dev_ref_clk(host->generic_phy);
+ }
+ vote = host->bus_vote.min_bw_vote;
+ }
+
+ err = ufs_qcom_set_bus_vote(host, vote);
+ if (err)
+ dev_err(hba->dev, "%s: set bus vote failed %d\n",
+ __func__, err);
+
+out:
+ return err;
+}
+
+#define ANDROID_BOOT_DEV_MAX 30
+static char android_boot_dev[ANDROID_BOOT_DEV_MAX];
+static int get_android_boot_dev(char *str)
+{
+ strlcpy(android_boot_dev, str, ANDROID_BOOT_DEV_MAX);
+ return 1;
+}
+__setup("androidboot.bootdevice=", get_android_boot_dev);
+
+/**
+ * ufs_qcom_init - bind phy with controller
+ * @hba: host controller instance
+ *
+ * Binds PHY with controller and powers up PHY enabling clocks
+ * and regulators.
+ *
+ * Returns -EPROBE_DEFER if binding fails, returns negative error
+ * on phy power up failure and returns zero on success.
+ */
+static int ufs_qcom_init(struct ufs_hba *hba)
+{
+ int err;
+ struct device *dev = hba->dev;
+ struct ufs_qcom_host *host;
+
+ if (strlen(android_boot_dev) && strcmp(android_boot_dev, dev_name(dev)))
+ return -ENODEV;
+
+ host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
+ if (!host) {
+ err = -ENOMEM;
+ dev_err(dev, "%s: no memory for qcom ufs host\n", __func__);
+ goto out;
+ }
+
+ host->hba = hba;
+ hba->priv = (void *)host;
+
+ err = ufs_qcom_ice_get_dev(host);
+ if (err == -EPROBE_DEFER) {
+ /*
+ * UFS driver might be probed before ICE driver does.
+ * In that case we would like to return EPROBE_DEFER code
+ * in order to delay its probing.
+ */
+ dev_err(dev, "%s: required ICE device not probed yet err = %d\n",
+ __func__, err);
+ goto out_host_free;
+
+ } else if (err == -ENODEV) {
+ /*
+ * ICE device is not enabled in DTS file. No need for further
+ * initialization of ICE driver.
+ */
+ dev_warn(dev, "%s: ICE device is not enabled",
+ __func__);
+ } else if (err) {
+ dev_err(dev, "%s: ufs_qcom_ice_get_dev failed %d\n",
+ __func__, err);
+ goto out_host_free;
+ }
+
+ host->generic_phy = devm_phy_get(dev, "ufsphy");
+
+ if (IS_ERR(host->generic_phy)) {
+ err = PTR_ERR(host->generic_phy);
+ dev_err(dev, "%s: PHY get failed %d\n", __func__, err);
+ goto out;
+ }
+
+ /* restore the secure configuration */
+ ufs_qcom_update_sec_cfg(hba, true);
+
+ phy_init(host->generic_phy);
+ err = phy_power_on(host->generic_phy);
+ if (err)
+ goto out_unregister_bus;
+
+ err = ufs_qcom_init_lanes(host);
+ if (err)
+ goto out_disable_phy;
+
+ ufs_qcom_advertise_quirks(hba);
+
+ hba->caps |= UFSHCD_CAP_CLK_GATING | UFSHCD_CAP_CLK_SCALING;
+ hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND;
+
+ ufs_qcom_setup_clocks(hba, true);
+ if (host->ice.pdev) {
+ err = ufs_qcom_ice_init(host);
+ if (err) {
+ dev_err(dev, "%s: ICE driver initialization failed (%d)\n",
+ __func__, err);
+ device_remove_file(dev, &host->bus_vote.max_bus_bw);
+ goto out_disable_phy;
+ }
+ }
+
+ if (hba->dev->id < MAX_UFS_QCOM_HOSTS)
+ ufs_qcom_hosts[hba->dev->id] = host;
+
+ goto out;
+
+out_disable_phy:
+ phy_power_off(host->generic_phy);
+out_unregister_bus:
+ phy_exit(host->generic_phy);
+out_host_free:
+ devm_kfree(dev, host);
+ hba->priv = NULL;
+out:
+ return err;
+}
+
+static void ufs_qcom_exit(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+
+ ufs_qcom_disable_lane_clks(host);
+ phy_power_off(host->generic_phy);
+}
+
+
+static void ufs_qcom_clk_scale_notify(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = hba->priv;
+ struct ufs_pa_layer_attr *dev_req_params = &host->dev_req_params;
+
+ if (!dev_req_params)
+ return;
+
+ ufs_qcom_cfg_timers(hba, dev_req_params->gear_rx,
+ dev_req_params->pwr_rx,
+ dev_req_params->hs_rate);
+ ufs_qcom_update_bus_bw_vote(host);
+}
+
+/*
+ * This function should be called to restore the security configuration of UFS
+ * register space after coming out of UFS host core power collapse.
+ *
+ * @hba: host controller instance
+ * @restore_sec_cfg: Set "true" if secure configuration needs to be restored
+ * and set "false" when secure configuration is lost.
+ */
+static int ufs_qcom_update_sec_cfg(struct ufs_hba *hba, bool restore_sec_cfg)
+{
+ int ret = 0, scm_ret = 0;
+ struct ufs_qcom_host *host = hba->priv;
+
+ /* scm command buffer structrue */
+ struct msm_scm_cmd_buf {
+ unsigned int device_id;
+ unsigned int spare;
+ } cbuf = {0};
+ #define RESTORE_SEC_CFG_CMD 0x2
+ #define UFS_TZ_DEV_ID 19
+
+ if (!host || !hba->vreg_info.vdd_hba ||
+ !(host->sec_cfg_updated ^ restore_sec_cfg)) {
+ return 0;
+ } else if (!restore_sec_cfg) {
+ /*
+ * Clear the flag so next time when this function is called
+ * with restore_sec_cfg set to true, we can restore the secure
+ * configuration.
+ */
+ host->sec_cfg_updated = false;
+ goto out;
+ } else if (hba->clk_gating.state != CLKS_ON) {
+ /*
+ * Clocks should be ON to restore the host controller secure
+ * configuration.
+ */
+ goto out;
+ }
+
+ /*
+ * If we are here, Host controller clocks are running, Host controller
+ * power collapse feature is supported and Host controller has just came
+ * out of power collapse.
+ */
+ cbuf.device_id = UFS_TZ_DEV_ID;
+
+out:
+ dev_dbg(hba->dev, "%s: ip: restore_sec_cfg %d, op: restore_sec_cfg %d, ret %d scm_ret %d\n",
+ __func__, restore_sec_cfg, host->sec_cfg_updated, ret, scm_ret);
+ return ret;
+}
+
+/**
+ * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
+ *
+ * The variant operations configure the necessary controller and PHY
+ * handshake during initialization.
+ */
+static const struct ufs_hba_variant_ops ufs_hba_qcom_vops = {
+ .name = "qcom",
+ .init = ufs_qcom_init,
+ .exit = ufs_qcom_exit,
+ .clk_scale_notify = ufs_qcom_clk_scale_notify,
+ .setup_clocks = ufs_qcom_setup_clocks,
+ .hce_enable_notify = ufs_qcom_hce_enable_notify,
+ .link_startup_notify = ufs_qcom_link_startup_notify,
+ .pwr_change_notify = ufs_qcom_pwr_change_notify,
+ .suspend = ufs_qcom_suspend,
+ .resume = ufs_qcom_resume,
+ .update_sec_cfg = ufs_qcom_update_sec_cfg,
+ .crypto_engine_cfg = ufs_qcom_crytpo_engine_cfg,
+ .crypto_engine_eh = ufs_qcom_crypto_engine_eh,
+ .crypto_engine_get_err = ufs_qcom_crypto_engine_get_err,
+ .crypto_engine_reset_err = ufs_qcom_crypto_engine_reset_err,
+};
+EXPORT_SYMBOL(ufs_hba_qcom_vops);
diff --git a/drivers/scsi/ufs/ufs.h b/drivers/scsi/ufs/ufs.h
deleted file mode 100644
index 42c459a..0000000
--- a/drivers/scsi/ufs/ufs.h
+++ /dev/null
@@ -1,491 +0,0 @@
-/*
- * Universal Flash Storage Host controller driver
- *
- * This code is based on drivers/scsi/ufs/ufs.h
- * Copyright (C) 2011-2013 Samsung India Software Operations
- *
- * Authors:
- * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx>
- * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * See the COPYING file in the top-level directory or visit
- * <http://www.gnu.org/licenses/gpl-2.0.html>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * This program is provided "AS IS" and "WITH ALL FAULTS" and
- * without warranty of any kind. You are solely responsible for
- * determining the appropriateness of using and distributing
- * the program and assume all risks associated with your exercise
- * of rights with respect to the program, including but not limited
- * to infringement of third party rights, the risks and costs of
- * program errors, damage to or loss of data, programs or equipment,
- * and unavailability or interruption of operations. Under no
- * circumstances will the contributor of this Program be liable for
- * any damages of any kind arising from your use or distribution of
- * this program.
- */
-
-#ifndef _UFS_H
-#define _UFS_H
-
-#include <linux/mutex.h>
-#include <linux/types.h>
-
-#define MAX_CDB_SIZE 16
-#define GENERAL_UPIU_REQUEST_SIZE 32
-#define QUERY_DESC_MAX_SIZE 255
-#define QUERY_DESC_MIN_SIZE 2
-#define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \
- (sizeof(struct utp_upiu_header)))
-
-#define UPIU_HEADER_DWORD(byte3, byte2, byte1, byte0)\
- cpu_to_be32((byte3 << 24) | (byte2 << 16) |\
- (byte1 << 8) | (byte0))
-/*
- * UFS device may have standard LUs and LUN id could be from 0x00 to
- * 0x7F. Standard LUs use "Peripheral Device Addressing Format".
- * UFS device may also have the Well Known LUs (also referred as W-LU)
- * which again could be from 0x00 to 0x7F. For W-LUs, device only use
- * the "Extended Addressing Format" which means the W-LUNs would be
- * from 0xc100 (SCSI_W_LUN_BASE) onwards.
- * This means max. LUN number reported from UFS device could be 0xC17F.
- */
-#define UFS_UPIU_MAX_UNIT_NUM_ID 0x7F
-#define UFS_MAX_LUNS (SCSI_W_LUN_BASE + UFS_UPIU_MAX_UNIT_NUM_ID)
-#define UFS_UPIU_WLUN_ID (1 << 7)
-#define UFS_UPIU_MAX_GENERAL_LUN 8
-
-/* Well known logical unit id in LUN field of UPIU */
-enum {
- UFS_UPIU_REPORT_LUNS_WLUN = 0x81,
- UFS_UPIU_UFS_DEVICE_WLUN = 0xD0,
- UFS_UPIU_BOOT_WLUN = 0xB0,
- UFS_UPIU_RPMB_WLUN = 0xC4,
-};
-
-/*
- * UFS Protocol Information Unit related definitions
- */
-
-/* Task management functions */
-enum {
- UFS_ABORT_TASK = 0x01,
- UFS_ABORT_TASK_SET = 0x02,
- UFS_CLEAR_TASK_SET = 0x04,
- UFS_LOGICAL_RESET = 0x08,
- UFS_QUERY_TASK = 0x80,
- UFS_QUERY_TASK_SET = 0x81,
-};
-
-/* UTP UPIU Transaction Codes Initiator to Target */
-enum {
- UPIU_TRANSACTION_NOP_OUT = 0x00,
- UPIU_TRANSACTION_COMMAND = 0x01,
- UPIU_TRANSACTION_DATA_OUT = 0x02,
- UPIU_TRANSACTION_TASK_REQ = 0x04,
- UPIU_TRANSACTION_QUERY_REQ = 0x16,
-};
-
-/* UTP UPIU Transaction Codes Target to Initiator */
-enum {
- UPIU_TRANSACTION_NOP_IN = 0x20,
- UPIU_TRANSACTION_RESPONSE = 0x21,
- UPIU_TRANSACTION_DATA_IN = 0x22,
- UPIU_TRANSACTION_TASK_RSP = 0x24,
- UPIU_TRANSACTION_READY_XFER = 0x31,
- UPIU_TRANSACTION_QUERY_RSP = 0x36,
- UPIU_TRANSACTION_REJECT_UPIU = 0x3F,
-};
-
-/* UPIU Read/Write flags */
-enum {
- UPIU_CMD_FLAGS_NONE = 0x00,
- UPIU_CMD_FLAGS_WRITE = 0x20,
- UPIU_CMD_FLAGS_READ = 0x40,
-};
-
-/* UPIU Task Attributes */
-enum {
- UPIU_TASK_ATTR_SIMPLE = 0x00,
- UPIU_TASK_ATTR_ORDERED = 0x01,
- UPIU_TASK_ATTR_HEADQ = 0x02,
- UPIU_TASK_ATTR_ACA = 0x03,
-};
-
-/* UPIU Query request function */
-enum {
- UPIU_QUERY_FUNC_STANDARD_READ_REQUEST = 0x01,
- UPIU_QUERY_FUNC_STANDARD_WRITE_REQUEST = 0x81,
-};
-
-/* Flag idn for Query Requests*/
-enum flag_idn {
- QUERY_FLAG_IDN_FDEVICEINIT = 0x01,
- QUERY_FLAG_IDN_PWR_ON_WPE = 0x03,
- QUERY_FLAG_IDN_BKOPS_EN = 0x04,
-};
-
-/* Attribute idn for Query requests */
-enum attr_idn {
- QUERY_ATTR_IDN_ACTIVE_ICC_LVL = 0x03,
- QUERY_ATTR_IDN_BKOPS_STATUS = 0x05,
- QUERY_ATTR_IDN_EE_CONTROL = 0x0D,
- QUERY_ATTR_IDN_EE_STATUS = 0x0E,
-};
-
-/* Descriptor idn for Query requests */
-enum desc_idn {
- QUERY_DESC_IDN_DEVICE = 0x0,
- QUERY_DESC_IDN_CONFIGURAION = 0x1,
- QUERY_DESC_IDN_UNIT = 0x2,
- QUERY_DESC_IDN_RFU_0 = 0x3,
- QUERY_DESC_IDN_INTERCONNECT = 0x4,
- QUERY_DESC_IDN_STRING = 0x5,
- QUERY_DESC_IDN_RFU_1 = 0x6,
- QUERY_DESC_IDN_GEOMETRY = 0x7,
- QUERY_DESC_IDN_POWER = 0x8,
- QUERY_DESC_IDN_MAX,
-};
-
-enum desc_header_offset {
- QUERY_DESC_LENGTH_OFFSET = 0x00,
- QUERY_DESC_DESC_TYPE_OFFSET = 0x01,
-};
-
-enum ufs_desc_max_size {
- QUERY_DESC_DEVICE_MAX_SIZE = 0x1F,
- QUERY_DESC_CONFIGURAION_MAX_SIZE = 0x90,
- QUERY_DESC_UNIT_MAX_SIZE = 0x23,
- QUERY_DESC_INTERCONNECT_MAX_SIZE = 0x06,
- /*
- * Max. 126 UNICODE characters (2 bytes per character) plus 2 bytes
- * of descriptor header.
- */
- QUERY_DESC_STRING_MAX_SIZE = 0xFE,
- QUERY_DESC_GEOMETRY_MAZ_SIZE = 0x44,
- QUERY_DESC_POWER_MAX_SIZE = 0x62,
- QUERY_DESC_RFU_MAX_SIZE = 0x00,
-};
-
-/* Unit descriptor parameters offsets in bytes*/
-enum unit_desc_param {
- UNIT_DESC_PARAM_LEN = 0x0,
- UNIT_DESC_PARAM_TYPE = 0x1,
- UNIT_DESC_PARAM_UNIT_INDEX = 0x2,
- UNIT_DESC_PARAM_LU_ENABLE = 0x3,
- UNIT_DESC_PARAM_BOOT_LUN_ID = 0x4,
- UNIT_DESC_PARAM_LU_WR_PROTECT = 0x5,
- UNIT_DESC_PARAM_LU_Q_DEPTH = 0x6,
- UNIT_DESC_PARAM_MEM_TYPE = 0x8,
- UNIT_DESC_PARAM_DATA_RELIABILITY = 0x9,
- UNIT_DESC_PARAM_LOGICAL_BLK_SIZE = 0xA,
- UNIT_DESC_PARAM_LOGICAL_BLK_COUNT = 0xB,
- UNIT_DESC_PARAM_ERASE_BLK_SIZE = 0x13,
- UNIT_DESC_PARAM_PROVISIONING_TYPE = 0x17,
- UNIT_DESC_PARAM_PHY_MEM_RSRC_CNT = 0x18,
- UNIT_DESC_PARAM_CTX_CAPABILITIES = 0x20,
- UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1 = 0x22,
-};
-
-/*
- * Logical Unit Write Protect
- * 00h: LU not write protected
- * 01h: LU write protected when fPowerOnWPEn =1
- * 02h: LU permanently write protected when fPermanentWPEn =1
- */
-enum ufs_lu_wp_type {
- UFS_LU_NO_WP = 0x00,
- UFS_LU_POWER_ON_WP = 0x01,
- UFS_LU_PERM_WP = 0x02,
-};
-
-/* bActiveICCLevel parameter current units */
-enum {
- UFSHCD_NANO_AMP = 0,
- UFSHCD_MICRO_AMP = 1,
- UFSHCD_MILI_AMP = 2,
- UFSHCD_AMP = 3,
-};
-
-#define POWER_DESC_MAX_SIZE 0x62
-#define POWER_DESC_MAX_ACTV_ICC_LVLS 16
-
-/* Attribute bActiveICCLevel parameter bit masks definitions */
-#define ATTR_ICC_LVL_UNIT_OFFSET 14
-#define ATTR_ICC_LVL_UNIT_MASK (0x3 << ATTR_ICC_LVL_UNIT_OFFSET)
-#define ATTR_ICC_LVL_VALUE_MASK 0x3FF
-
-/* Power descriptor parameters offsets in bytes */
-enum power_desc_param_offset {
- PWR_DESC_LEN = 0x0,
- PWR_DESC_TYPE = 0x1,
- PWR_DESC_ACTIVE_LVLS_VCC_0 = 0x2,
- PWR_DESC_ACTIVE_LVLS_VCCQ_0 = 0x22,
- PWR_DESC_ACTIVE_LVLS_VCCQ2_0 = 0x42,
-};
-
-/* Exception event mask values */
-enum {
- MASK_EE_STATUS = 0xFFFF,
- MASK_EE_URGENT_BKOPS = (1 << 2),
-};
-
-/* Background operation status */
-enum bkops_status {
- BKOPS_STATUS_NO_OP = 0x0,
- BKOPS_STATUS_NON_CRITICAL = 0x1,
- BKOPS_STATUS_PERF_IMPACT = 0x2,
- BKOPS_STATUS_CRITICAL = 0x3,
- BKOPS_STATUS_MAX = BKOPS_STATUS_CRITICAL,
-};
-
-/* UTP QUERY Transaction Specific Fields OpCode */
-enum query_opcode {
- UPIU_QUERY_OPCODE_NOP = 0x0,
- UPIU_QUERY_OPCODE_READ_DESC = 0x1,
- UPIU_QUERY_OPCODE_WRITE_DESC = 0x2,
- UPIU_QUERY_OPCODE_READ_ATTR = 0x3,
- UPIU_QUERY_OPCODE_WRITE_ATTR = 0x4,
- UPIU_QUERY_OPCODE_READ_FLAG = 0x5,
- UPIU_QUERY_OPCODE_SET_FLAG = 0x6,
- UPIU_QUERY_OPCODE_CLEAR_FLAG = 0x7,
- UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8,
-};
-
-/* Query response result code */
-enum {
- QUERY_RESULT_SUCCESS = 0x00,
- QUERY_RESULT_NOT_READABLE = 0xF6,
- QUERY_RESULT_NOT_WRITEABLE = 0xF7,
- QUERY_RESULT_ALREADY_WRITTEN = 0xF8,
- QUERY_RESULT_INVALID_LENGTH = 0xF9,
- QUERY_RESULT_INVALID_VALUE = 0xFA,
- QUERY_RESULT_INVALID_SELECTOR = 0xFB,
- QUERY_RESULT_INVALID_INDEX = 0xFC,
- QUERY_RESULT_INVALID_IDN = 0xFD,
- QUERY_RESULT_INVALID_OPCODE = 0xFE,
- QUERY_RESULT_GENERAL_FAILURE = 0xFF,
-};
-
-/* UTP Transfer Request Command Type (CT) */
-enum {
- UPIU_COMMAND_SET_TYPE_SCSI = 0x0,
- UPIU_COMMAND_SET_TYPE_UFS = 0x1,
- UPIU_COMMAND_SET_TYPE_QUERY = 0x2,
-};
-
-/* UTP Transfer Request Command Offset */
-#define UPIU_COMMAND_TYPE_OFFSET 28
-
-/* Offset of the response code in the UPIU header */
-#define UPIU_RSP_CODE_OFFSET 8
-
-enum {
- MASK_SCSI_STATUS = 0xFF,
- MASK_TASK_RESPONSE = 0xFF00,
- MASK_RSP_UPIU_RESULT = 0xFFFF,
- MASK_QUERY_DATA_SEG_LEN = 0xFFFF,
- MASK_RSP_UPIU_DATA_SEG_LEN = 0xFFFF,
- MASK_RSP_EXCEPTION_EVENT = 0x10000,
-};
-
-/* Task management service response */
-enum {
- UPIU_TASK_MANAGEMENT_FUNC_COMPL = 0x00,
- UPIU_TASK_MANAGEMENT_FUNC_NOT_SUPPORTED = 0x04,
- UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED = 0x08,
- UPIU_TASK_MANAGEMENT_FUNC_FAILED = 0x05,
- UPIU_INCORRECT_LOGICAL_UNIT_NO = 0x09,
-};
-
-/* UFS device power modes */
-enum ufs_dev_pwr_mode {
- UFS_ACTIVE_PWR_MODE = 1,
- UFS_SLEEP_PWR_MODE = 2,
- UFS_POWERDOWN_PWR_MODE = 3,
-};
-
-/**
- * struct utp_upiu_header - UPIU header structure
- * @dword_0: UPIU header DW-0
- * @dword_1: UPIU header DW-1
- * @dword_2: UPIU header DW-2
- */
-struct utp_upiu_header {
- __be32 dword_0;
- __be32 dword_1;
- __be32 dword_2;
-};
-
-/**
- * struct utp_upiu_cmd - Command UPIU structure
- * @data_transfer_len: Data Transfer Length DW-3
- * @cdb: Command Descriptor Block CDB DW-4 to DW-7
- */
-struct utp_upiu_cmd {
- __be32 exp_data_transfer_len;
- u8 cdb[MAX_CDB_SIZE];
-};
-
-/**
- * struct utp_upiu_query - upiu request buffer structure for
- * query request.
- * @opcode: command to perform B-0
- * @idn: a value that indicates the particular type of data B-1
- * @index: Index to further identify data B-2
- * @selector: Index to further identify data B-3
- * @reserved_osf: spec reserved field B-4,5
- * @length: number of descriptor bytes to read/write B-6,7
- * @value: Attribute value to be written DW-5
- * @reserved: spec reserved DW-6,7
- */
-struct utp_upiu_query {
- u8 opcode;
- u8 idn;
- u8 index;
- u8 selector;
- __be16 reserved_osf;
- __be16 length;
- __be32 value;
- __be32 reserved[2];
-};
-
-/**
- * struct utp_upiu_req - general upiu request structure
- * @header:UPIU header structure DW-0 to DW-2
- * @sc: fields structure for scsi command DW-3 to DW-7
- * @qr: fields structure for query request DW-3 to DW-7
- */
-struct utp_upiu_req {
- struct utp_upiu_header header;
- union {
- struct utp_upiu_cmd sc;
- struct utp_upiu_query qr;
- };
-};
-
-/**
- * struct utp_cmd_rsp - Response UPIU structure
- * @residual_transfer_count: Residual transfer count DW-3
- * @reserved: Reserved double words DW-4 to DW-7
- * @sense_data_len: Sense data length DW-8 U16
- * @sense_data: Sense data field DW-8 to DW-12
- */
-struct utp_cmd_rsp {
- __be32 residual_transfer_count;
- __be32 reserved[4];
- __be16 sense_data_len;
- u8 sense_data[18];
-};
-
-/**
- * struct utp_upiu_rsp - general upiu response structure
- * @header: UPIU header structure DW-0 to DW-2
- * @sr: fields structure for scsi command DW-3 to DW-12
- * @qr: fields structure for query request DW-3 to DW-7
- */
-struct utp_upiu_rsp {
- struct utp_upiu_header header;
- union {
- struct utp_cmd_rsp sr;
- struct utp_upiu_query qr;
- };
-};
-
-/**
- * struct utp_upiu_task_req - Task request UPIU structure
- * @header - UPIU header structure DW0 to DW-2
- * @input_param1: Input parameter 1 DW-3
- * @input_param2: Input parameter 2 DW-4
- * @input_param3: Input parameter 3 DW-5
- * @reserved: Reserved double words DW-6 to DW-7
- */
-struct utp_upiu_task_req {
- struct utp_upiu_header header;
- __be32 input_param1;
- __be32 input_param2;
- __be32 input_param3;
- __be32 reserved[2];
-};
-
-/**
- * struct utp_upiu_task_rsp - Task Management Response UPIU structure
- * @header: UPIU header structure DW0-DW-2
- * @output_param1: Ouput parameter 1 DW3
- * @output_param2: Output parameter 2 DW4
- * @reserved: Reserved double words DW-5 to DW-7
- */
-struct utp_upiu_task_rsp {
- struct utp_upiu_header header;
- __be32 output_param1;
- __be32 output_param2;
- __be32 reserved[3];
-};
-
-/**
- * struct ufs_query_req - parameters for building a query request
- * @query_func: UPIU header query function
- * @upiu_req: the query request data
- */
-struct ufs_query_req {
- u8 query_func;
- struct utp_upiu_query upiu_req;
-};
-
-/**
- * struct ufs_query_resp - UPIU QUERY
- * @response: device response code
- * @upiu_res: query response data
- */
-struct ufs_query_res {
- u8 response;
- struct utp_upiu_query upiu_res;
-};
-
-#define UFS_VREG_VCC_MIN_UV 2700000 /* uV */
-#define UFS_VREG_VCC_MAX_UV 3600000 /* uV */
-#define UFS_VREG_VCC_1P8_MIN_UV 1700000 /* uV */
-#define UFS_VREG_VCC_1P8_MAX_UV 1950000 /* uV */
-#define UFS_VREG_VCCQ_MIN_UV 1100000 /* uV */
-#define UFS_VREG_VCCQ_MAX_UV 1300000 /* uV */
-#define UFS_VREG_VCCQ2_MIN_UV 1650000 /* uV */
-#define UFS_VREG_VCCQ2_MAX_UV 1950000 /* uV */
-
-/*
- * VCCQ & VCCQ2 current requirement when UFS device is in sleep state
- * and link is in Hibern8 state.
- */
-#define UFS_VREG_LPM_LOAD_UA 1000 /* uA */
-
-struct ufs_vreg {
- struct regulator *reg;
- const char *name;
- bool enabled;
- int min_uV;
- int max_uV;
- int min_uA;
- int max_uA;
-};
-
-struct ufs_vreg_info {
- struct ufs_vreg *vcc;
- struct ufs_vreg *vccq;
- struct ufs_vreg *vccq2;
- struct ufs_vreg *vdd_hba;
-};
-
-struct ufs_dev_info {
- bool f_power_on_wp_en;
- /* Keeps information if any of the LU is power on write protected */
- bool is_lu_power_on_wp;
-};
-
-#endif /* End of Header */
diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c
index 955ed55..2a18b8e 100644
--- a/drivers/scsi/ufs/ufshcd-pci.c
+++ b/drivers/scsi/ufs/ufshcd-pci.c
@@ -33,7 +33,7 @@
* this program.
*/
-#include "ufshcd.h"
+#include <linux/scsi/ufs/ufshcd.h>
#include <linux/pci.h>
#include <linux/pm_runtime.h>
diff --git a/drivers/scsi/ufs/ufshcd-pltfrm.c b/drivers/scsi/ufs/ufshcd-pltfrm.c
index 1c3467b..5170811 100644
--- a/drivers/scsi/ufs/ufshcd-pltfrm.c
+++ b/drivers/scsi/ufs/ufshcd-pltfrm.c
@@ -37,7 +37,7 @@
#include <linux/pm_runtime.h>
#include <linux/of.h>
-#include "ufshcd.h"
+#include <linux/scsi/ufs/ufshcd.h>
static const struct of_device_id ufs_of_match[];
static struct ufs_hba_variant_ops *get_variant_ops(struct device *dev)
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index a7ff00d..815eccb 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -40,8 +40,9 @@
#include <linux/async.h>
#include <linux/devfreq.h>
-#include "ufshcd.h"
-#include "unipro.h"
+#include <linux/scsi/ufs/ufshcd.h>
+#include <linux/scsi/ufs/unipro.h>
+#include "ufshci.h"
#define UFSHCD_ENABLE_INTRS (UTP_TRANSFER_REQ_COMPL |\
UTP_TASK_REQ_COMPL |\
@@ -778,11 +779,24 @@ static void ufshcd_clk_scaling_update_busy(struct ufs_hba *hba)
* @task_tag: Task tag of the command
*/
static inline
-void ufshcd_send_command(struct ufs_hba *hba, unsigned int task_tag)
+int ufshcd_send_command(struct ufs_hba *hba, unsigned int task_tag)
{
+ int ret = 0;
+
+ if (hba->vops->crypto_engine_cfg) {
+ ret = hba->vops->crypto_engine_cfg(hba, task_tag);
+ if (ret) {
+ dev_err(hba->dev,
+ "%s: failed to configure crypto engine %d\n",
+ __func__, ret);
+ return ret;
+ }
+ }
ufshcd_clk_scaling_start_busy(hba);
__set_bit(task_tag, &hba->outstanding_reqs);
ufshcd_writel(hba, 1 << task_tag, REG_UTP_TRANSFER_REQ_DOOR_BELL);
+
+ return ret;
}
/**
@@ -1335,7 +1349,14 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)
/* issue command to the controller */
spin_lock_irqsave(hba->host->host_lock, flags);
- ufshcd_send_command(hba, tag);
+
+ err = ufshcd_send_command(hba, tag);
+ if (err) {
+ dev_err(hba->dev, "%s: failed sending command, %d\n",
+ __func__, err);
+ err = DID_ERROR;
+ }
+
out_unlock:
spin_unlock_irqrestore(hba->host->host_lock, flags);
out:
@@ -1535,9 +1556,13 @@ static int ufshcd_exec_dev_cmd(struct ufs_hba *hba,
hba->dev_cmd.complete = &wait;
spin_lock_irqsave(hba->host->host_lock, flags);
- ufshcd_send_command(hba, tag);
+ err = ufshcd_send_command(hba, tag);
spin_unlock_irqrestore(hba->host->host_lock, flags);
-
+ if (err) {
+ dev_err(hba->dev, "%s: failed sending command, %d\n",
+ __func__, err);
+ goto out_put_tag;
+ }
err = ufshcd_wait_for_dev_cmd(hba, lrbp, timeout);
out_put_tag:
@@ -2516,6 +2541,15 @@ out:
}
/**
+ * ufshcd_hba_stop - Send controller to reset state
+ * @hba: per adapter instance
+ */
+static inline void ufshcd_hba_stop(struct ufs_hba *hba)
+{
+ ufshcd_writel(hba, CONTROLLER_DISABLE, REG_CONTROLLER_ENABLE);
+}
+
+/**
* ufshcd_hba_enable - initialize the controller
* @hba: per adapter instance
*
@@ -3017,6 +3051,42 @@ static void ufshcd_uic_cmd_compl(struct ufs_hba *hba, u32 intr_status)
}
/**
+ * ufshcd_abort_outstanding_requests - abort all outstanding transfer requests.
+ * @hba: per adapter instance
+ * @result: error result to inform scsi layer about
+ */
+void ufshcd_abort_outstanding_transfer_requests(struct ufs_hba *hba, int result)
+{
+ u8 index;
+ struct ufshcd_lrb *lrbp;
+ struct scsi_cmnd *cmd;
+
+ if (!hba->outstanding_reqs)
+ return;
+
+ for_each_set_bit(index, &hba->outstanding_reqs, hba->nutrs) {
+ lrbp = &hba->lrb[index];
+ cmd = lrbp->cmd;
+ if (cmd) {
+ scsi_dma_unmap(cmd);
+ cmd->result = result;
+ /* Mark completed command as NULL in LRB */
+ lrbp->cmd = NULL;
+ /* Clear pending transfer requests */
+ ufshcd_clear_cmd(hba, index);
+ __clear_bit(index, &hba->outstanding_tasks);
+ clear_bit_unlock(index, &hba->lrb_in_use);
+ /* Do not touch lrbp after scsi done */
+ cmd->scsi_done(cmd);
+ ufshcd_release(hba);
+ } else if (lrbp->command_type == UTP_CMD_TYPE_DEV_MANAGE) {
+ if (hba->dev_cmd.complete)
+ complete(hba->dev_cmd.complete);
+ }
+ }
+}
+
+/**
* ufshcd_transfer_req_compl - handle SCSI and query command completion
* @hba: per adapter instance
*/
@@ -3336,6 +3406,7 @@ static void ufshcd_err_handler(struct work_struct *work)
u32 err_tm = 0;
int err = 0;
int tag;
+ int crypto_engine_err = 0;
hba = container_of(work, struct ufs_hba, eh_work);
@@ -3354,6 +3425,9 @@ static void ufshcd_err_handler(struct work_struct *work)
/* Complete requests that have door-bell cleared by h/w */
ufshcd_transfer_req_compl(hba);
ufshcd_tmc_handler(hba);
+
+ if (hba->vops && hba->vops->crypto_engine_get_err)
+ crypto_engine_err = hba->vops->crypto_engine_get_err(hba);
spin_unlock_irqrestore(hba->host->host_lock, flags);
/* Clear pending transfer requests */
@@ -3435,8 +3509,12 @@ static void ufshcd_update_uic_error(struct ufs_hba *hba)
static void ufshcd_check_errors(struct ufs_hba *hba)
{
bool queue_eh_work = false;
+ int crypto_engine_err = 0;
- if (hba->errors & INT_FATAL_ERRORS)
+ if (hba->vops && hba->vops->crypto_engine_get_err)
+ crypto_engine_err = hba->vops->crypto_engine_get_err(hba);
+
+ if (hba->errors & INT_FATAL_ERRORS || crypto_engine_err)
queue_eh_work = true;
if (hba->errors & UIC_ERROR) {
@@ -3488,6 +3566,11 @@ static void ufshcd_tmc_handler(struct ufs_hba *hba)
*/
static void ufshcd_sl_intr(struct ufs_hba *hba, u32 intr_status)
{
+ bool crypto_engine_err = false;
+
+ if (hba->vops && hba->vops->crypto_engine_eh)
+ crypto_engine_err = hba->vops->crypto_engine_eh(hba);
+
hba->errors = UFSHCD_ERROR_MASK & intr_status;
if (hba->errors)
ufshcd_check_errors(hba);
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
deleted file mode 100644
index 4a574aa..0000000
--- a/drivers/scsi/ufs/ufshcd.h
+++ /dev/null
@@ -1,596 +0,0 @@
-/*
- * Universal Flash Storage Host controller driver
- *
- * This code is based on drivers/scsi/ufs/ufshcd.h
- * Copyright (C) 2011-2013 Samsung India Software Operations
- *
- * Authors:
- * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx>
- * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * See the COPYING file in the top-level directory or visit
- * <http://www.gnu.org/licenses/gpl-2.0.html>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * This program is provided "AS IS" and "WITH ALL FAULTS" and
- * without warranty of any kind. You are solely responsible for
- * determining the appropriateness of using and distributing
- * the program and assume all risks associated with your exercise
- * of rights with respect to the program, including but not limited
- * to infringement of third party rights, the risks and costs of
- * program errors, damage to or loss of data, programs or equipment,
- * and unavailability or interruption of operations. Under no
- * circumstances will the contributor of this Program be liable for
- * any damages of any kind arising from your use or distribution of
- * this program.
- */
-
-#ifndef _UFSHCD_H
-#define _UFSHCD_H
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/spinlock.h>
-#include <linux/workqueue.h>
-#include <linux/errno.h>
-#include <linux/types.h>
-#include <linux/wait.h>
-#include <linux/bitops.h>
-#include <linux/pm_runtime.h>
-#include <linux/clk.h>
-#include <linux/completion.h>
-#include <linux/regulator/consumer.h>
-
-#include <asm/irq.h>
-#include <asm/byteorder.h>
-#include <scsi/scsi.h>
-#include <scsi/scsi_cmnd.h>
-#include <scsi/scsi_host.h>
-#include <scsi/scsi_tcq.h>
-#include <scsi/scsi_dbg.h>
-#include <scsi/scsi_eh.h>
-
-#include "ufs.h"
-#include "ufshci.h"
-
-#define UFSHCD "ufshcd"
-#define UFSHCD_DRIVER_VERSION "0.2"
-
-struct ufs_hba;
-
-enum dev_cmd_type {
- DEV_CMD_TYPE_NOP = 0x0,
- DEV_CMD_TYPE_QUERY = 0x1,
-};
-
-/**
- * struct uic_command - UIC command structure
- * @command: UIC command
- * @argument1: UIC command argument 1
- * @argument2: UIC command argument 2
- * @argument3: UIC command argument 3
- * @cmd_active: Indicate if UIC command is outstanding
- * @result: UIC command result
- * @done: UIC command completion
- */
-struct uic_command {
- u32 command;
- u32 argument1;
- u32 argument2;
- u32 argument3;
- int cmd_active;
- int result;
- struct completion done;
-};
-
-/* Used to differentiate the power management options */
-enum ufs_pm_op {
- UFS_RUNTIME_PM,
- UFS_SYSTEM_PM,
- UFS_SHUTDOWN_PM,
-};
-
-#define ufshcd_is_runtime_pm(op) ((op) == UFS_RUNTIME_PM)
-#define ufshcd_is_system_pm(op) ((op) == UFS_SYSTEM_PM)
-#define ufshcd_is_shutdown_pm(op) ((op) == UFS_SHUTDOWN_PM)
-
-/* Host <-> Device UniPro Link state */
-enum uic_link_state {
- UIC_LINK_OFF_STATE = 0, /* Link powered down or disabled */
- UIC_LINK_ACTIVE_STATE = 1, /* Link is in Fast/Slow/Sleep state */
- UIC_LINK_HIBERN8_STATE = 2, /* Link is in Hibernate state */
-};
-
-#define ufshcd_is_link_off(hba) ((hba)->uic_link_state == UIC_LINK_OFF_STATE)
-#define ufshcd_is_link_active(hba) ((hba)->uic_link_state == \
- UIC_LINK_ACTIVE_STATE)
-#define ufshcd_is_link_hibern8(hba) ((hba)->uic_link_state == \
- UIC_LINK_HIBERN8_STATE)
-#define ufshcd_set_link_off(hba) ((hba)->uic_link_state = UIC_LINK_OFF_STATE)
-#define ufshcd_set_link_active(hba) ((hba)->uic_link_state = \
- UIC_LINK_ACTIVE_STATE)
-#define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \
- UIC_LINK_HIBERN8_STATE)
-
-/*
- * UFS Power management levels.
- * Each level is in increasing order of power savings.
- */
-enum ufs_pm_level {
- UFS_PM_LVL_0, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_ACTIVE_STATE */
- UFS_PM_LVL_1, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_HIBERN8_STATE */
- UFS_PM_LVL_2, /* UFS_SLEEP_PWR_MODE, UIC_LINK_ACTIVE_STATE */
- UFS_PM_LVL_3, /* UFS_SLEEP_PWR_MODE, UIC_LINK_HIBERN8_STATE */
- UFS_PM_LVL_4, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_HIBERN8_STATE */
- UFS_PM_LVL_5, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_OFF_STATE */
- UFS_PM_LVL_MAX
-};
-
-struct ufs_pm_lvl_states {
- enum ufs_dev_pwr_mode dev_state;
- enum uic_link_state link_state;
-};
-
-/**
- * struct ufshcd_lrb - local reference block
- * @utr_descriptor_ptr: UTRD address of the command
- * @ucd_req_ptr: UCD address of the command
- * @ucd_rsp_ptr: Response UPIU address for this command
- * @ucd_prdt_ptr: PRDT address of the command
- * @cmd: pointer to SCSI command
- * @sense_buffer: pointer to sense buffer address of the SCSI command
- * @sense_bufflen: Length of the sense buffer
- * @scsi_status: SCSI status of the command
- * @command_type: SCSI, UFS, Query.
- * @task_tag: Task tag of the command
- * @lun: LUN of the command
- * @intr_cmd: Interrupt command (doesn't participate in interrupt aggregation)
- */
-struct ufshcd_lrb {
- struct utp_transfer_req_desc *utr_descriptor_ptr;
- struct utp_upiu_req *ucd_req_ptr;
- struct utp_upiu_rsp *ucd_rsp_ptr;
- struct ufshcd_sg_entry *ucd_prdt_ptr;
-
- struct scsi_cmnd *cmd;
- u8 *sense_buffer;
- unsigned int sense_bufflen;
- int scsi_status;
-
- int command_type;
- int task_tag;
- u8 lun; /* UPIU LUN id field is only 8-bit wide */
- bool intr_cmd;
-};
-
-/**
- * struct ufs_query - holds relevent data structures for query request
- * @request: request upiu and function
- * @descriptor: buffer for sending/receiving descriptor
- * @response: response upiu and response
- */
-struct ufs_query {
- struct ufs_query_req request;
- u8 *descriptor;
- struct ufs_query_res response;
-};
-
-/**
- * struct ufs_dev_cmd - all assosiated fields with device management commands
- * @type: device management command type - Query, NOP OUT
- * @lock: lock to allow one command at a time
- * @complete: internal commands completion
- * @tag_wq: wait queue until free command slot is available
- */
-struct ufs_dev_cmd {
- enum dev_cmd_type type;
- struct mutex lock;
- struct completion *complete;
- wait_queue_head_t tag_wq;
- struct ufs_query query;
-};
-
-/**
- * struct ufs_clk_info - UFS clock related info
- * @list: list headed by hba->clk_list_head
- * @clk: clock node
- * @name: clock name
- * @max_freq: maximum frequency supported by the clock
- * @min_freq: min frequency that can be used for clock scaling
- * @curr_freq: indicates the current frequency that it is set to
- * @enabled: variable to check against multiple enable/disable
- */
-struct ufs_clk_info {
- struct list_head list;
- struct clk *clk;
- const char *name;
- u32 max_freq;
- u32 min_freq;
- u32 curr_freq;
- bool enabled;
-};
-
-#define PRE_CHANGE 0
-#define POST_CHANGE 1
-
-struct ufs_pa_layer_attr {
- u32 gear_rx;
- u32 gear_tx;
- u32 lane_rx;
- u32 lane_tx;
- u32 pwr_rx;
- u32 pwr_tx;
- u32 hs_rate;
-};
-
-struct ufs_pwr_mode_info {
- bool is_valid;
- struct ufs_pa_layer_attr info;
-};
-
-/**
- * struct ufs_hba_variant_ops - variant specific callbacks
- * @name: variant name
- * @init: called when the driver is initialized
- * @exit: called to cleanup everything done in init
- * @clk_scale_notify: notifies that clks are scaled up/down
- * @setup_clocks: called before touching any of the controller registers
- * @setup_regulators: called before accessing the host controller
- * @hce_enable_notify: called before and after HCE enable bit is set to allow
- * variant specific Uni-Pro initialization.
- * @link_startup_notify: called before and after Link startup is carried out
- * to allow variant specific Uni-Pro initialization.
- * @pwr_change_notify: called before and after a power mode change
- * is carried out to allow vendor spesific capabilities
- * to be set.
- * @suspend: called during host controller PM callback
- * @resume: called during host controller PM callback
- */
-struct ufs_hba_variant_ops {
- const char *name;
- int (*init)(struct ufs_hba *);
- void (*exit)(struct ufs_hba *);
- void (*clk_scale_notify)(struct ufs_hba *);
- int (*setup_clocks)(struct ufs_hba *, bool);
- int (*setup_regulators)(struct ufs_hba *, bool);
- int (*hce_enable_notify)(struct ufs_hba *, bool);
- int (*link_startup_notify)(struct ufs_hba *, bool);
- int (*pwr_change_notify)(struct ufs_hba *,
- bool, struct ufs_pa_layer_attr *,
- struct ufs_pa_layer_attr *);
- int (*suspend)(struct ufs_hba *, enum ufs_pm_op);
- int (*resume)(struct ufs_hba *, enum ufs_pm_op);
-};
-
-/* clock gating state */
-enum clk_gating_state {
- CLKS_OFF,
- CLKS_ON,
- REQ_CLKS_OFF,
- REQ_CLKS_ON,
-};
-
-/**
- * struct ufs_clk_gating - UFS clock gating related info
- * @gate_work: worker to turn off clocks after some delay as specified in
- * delay_ms
- * @ungate_work: worker to turn on clocks that will be used in case of
- * interrupt context
- * @state: the current clocks state
- * @delay_ms: gating delay in ms
- * @is_suspended: clk gating is suspended when set to 1 which can be used
- * during suspend/resume
- * @delay_attr: sysfs attribute to control delay_attr
- * @active_reqs: number of requests that are pending and should be waited for
- * completion before gating clocks.
- */
-struct ufs_clk_gating {
- struct delayed_work gate_work;
- struct work_struct ungate_work;
- enum clk_gating_state state;
- unsigned long delay_ms;
- bool is_suspended;
- struct device_attribute delay_attr;
- int active_reqs;
-};
-
-struct ufs_clk_scaling {
- ktime_t busy_start_t;
- bool is_busy_started;
- unsigned long tot_busy_t;
- unsigned long window_start_t;
-};
-
-/**
- * struct ufs_init_prefetch - contains data that is pre-fetched once during
- * initialization
- * @icc_level: icc level which was read during initialization
- */
-struct ufs_init_prefetch {
- u32 icc_level;
-};
-
-/**
- * struct ufs_hba - per adapter private structure
- * @mmio_base: UFSHCI base register address
- * @ucdl_base_addr: UFS Command Descriptor base address
- * @utrdl_base_addr: UTP Transfer Request Descriptor base address
- * @utmrdl_base_addr: UTP Task Management Descriptor base address
- * @ucdl_dma_addr: UFS Command Descriptor DMA address
- * @utrdl_dma_addr: UTRDL DMA address
- * @utmrdl_dma_addr: UTMRDL DMA address
- * @host: Scsi_Host instance of the driver
- * @dev: device handle
- * @lrb: local reference block
- * @lrb_in_use: lrb in use
- * @outstanding_tasks: Bits representing outstanding task requests
- * @outstanding_reqs: Bits representing outstanding transfer requests
- * @capabilities: UFS Controller Capabilities
- * @nutrs: Transfer Request Queue depth supported by controller
- * @nutmrs: Task Management Queue depth supported by controller
- * @ufs_version: UFS Version to which controller complies
- * @vops: pointer to variant specific operations
- * @priv: pointer to variant specific private data
- * @irq: Irq number of the controller
- * @active_uic_cmd: handle of active UIC command
- * @uic_cmd_mutex: mutex for uic command
- * @tm_wq: wait queue for task management
- * @tm_tag_wq: wait queue for free task management slots
- * @tm_slots_in_use: bit map of task management request slots in use
- * @pwr_done: completion for power mode change
- * @tm_condition: condition variable for task management
- * @ufshcd_state: UFSHCD states
- * @eh_flags: Error handling flags
- * @intr_mask: Interrupt Mask Bits
- * @ee_ctrl_mask: Exception event control mask
- * @is_powered: flag to check if HBA is powered
- * @is_init_prefetch: flag to check if data was pre-fetched in initialization
- * @init_prefetch_data: data pre-fetched during initialization
- * @eh_work: Worker to handle UFS errors that require s/w attention
- * @eeh_work: Worker to handle exception events
- * @errors: HBA errors
- * @uic_error: UFS interconnect layer error status
- * @saved_err: sticky error mask
- * @saved_uic_err: sticky UIC error mask
- * @dev_cmd: ufs device management command information
- * @auto_bkops_enabled: to track whether bkops is enabled in device
- * @vreg_info: UFS device voltage regulator information
- * @clk_list_head: UFS host controller clocks list node head
- * @pwr_info: holds current power mode
- * @max_pwr_info: keeps the device max valid pwm
- */
-struct ufs_hba {
- void __iomem *mmio_base;
-
- /* Virtual memory reference */
- struct utp_transfer_cmd_desc *ucdl_base_addr;
- struct utp_transfer_req_desc *utrdl_base_addr;
- struct utp_task_req_desc *utmrdl_base_addr;
-
- /* DMA memory reference */
- dma_addr_t ucdl_dma_addr;
- dma_addr_t utrdl_dma_addr;
- dma_addr_t utmrdl_dma_addr;
-
- struct Scsi_Host *host;
- struct device *dev;
- /*
- * This field is to keep a reference to "scsi_device" corresponding to
- * "UFS device" W-LU.
- */
- struct scsi_device *sdev_ufs_device;
-
- enum ufs_dev_pwr_mode curr_dev_pwr_mode;
- enum uic_link_state uic_link_state;
- /* Desired UFS power management level during runtime PM */
- enum ufs_pm_level rpm_lvl;
- /* Desired UFS power management level during system PM */
- enum ufs_pm_level spm_lvl;
- int pm_op_in_progress;
-
- struct ufshcd_lrb *lrb;
- unsigned long lrb_in_use;
-
- unsigned long outstanding_tasks;
- unsigned long outstanding_reqs;
-
- u32 capabilities;
- int nutrs;
- int nutmrs;
- u32 ufs_version;
- struct ufs_hba_variant_ops *vops;
- void *priv;
- unsigned int irq;
- bool is_irq_enabled;
-
-
- wait_queue_head_t tm_wq;
- wait_queue_head_t tm_tag_wq;
- unsigned long tm_condition;
- unsigned long tm_slots_in_use;
-
- struct uic_command *active_uic_cmd;
- struct mutex uic_cmd_mutex;
- struct completion *uic_async_done;
-
- u32 ufshcd_state;
- u32 eh_flags;
- u32 intr_mask;
- u16 ee_ctrl_mask;
- bool is_powered;
- bool is_init_prefetch;
- struct ufs_init_prefetch init_prefetch_data;
-
- /* Work Queues */
- struct work_struct eh_work;
- struct work_struct eeh_work;
-
- /* HBA Errors */
- u32 errors;
- u32 uic_error;
- u32 saved_err;
- u32 saved_uic_err;
-
- /* Device management request data */
- struct ufs_dev_cmd dev_cmd;
-
- /* Keeps information of the UFS device connected to this host */
- struct ufs_dev_info dev_info;
- bool auto_bkops_enabled;
- struct ufs_vreg_info vreg_info;
- struct list_head clk_list_head;
-
- bool wlun_dev_clr_ua;
-
- struct ufs_pa_layer_attr pwr_info;
- struct ufs_pwr_mode_info max_pwr_info;
-
- struct ufs_clk_gating clk_gating;
- /* Control to enable/disable host capabilities */
- u32 caps;
- /* Allow dynamic clk gating */
-#define UFSHCD_CAP_CLK_GATING (1 << 0)
- /* Allow hiberb8 with clk gating */
-#define UFSHCD_CAP_HIBERN8_WITH_CLK_GATING (1 << 1)
- /* Allow dynamic clk scaling */
-#define UFSHCD_CAP_CLK_SCALING (1 << 2)
- /* Allow auto bkops to enabled during runtime suspend */
-#define UFSHCD_CAP_AUTO_BKOPS_SUSPEND (1 << 3)
-
- struct devfreq *devfreq;
- struct ufs_clk_scaling clk_scaling;
- bool is_sys_suspended;
-};
-
-/* Returns true if clocks can be gated. Otherwise false */
-static inline bool ufshcd_is_clkgating_allowed(struct ufs_hba *hba)
-{
- return hba->caps & UFSHCD_CAP_CLK_GATING;
-}
-static inline bool ufshcd_can_hibern8_during_gating(struct ufs_hba *hba)
-{
- return hba->caps & UFSHCD_CAP_HIBERN8_WITH_CLK_GATING;
-}
-static inline int ufshcd_is_clkscaling_enabled(struct ufs_hba *hba)
-{
- return hba->caps & UFSHCD_CAP_CLK_SCALING;
-}
-static inline bool ufshcd_can_autobkops_during_suspend(struct ufs_hba *hba)
-{
- return hba->caps & UFSHCD_CAP_AUTO_BKOPS_SUSPEND;
-}
-
-#define ufshcd_writel(hba, val, reg) \
- writel((val), (hba)->mmio_base + (reg))
-#define ufshcd_readl(hba, reg) \
- readl((hba)->mmio_base + (reg))
-
-/**
- * ufshcd_rmwl - read modify write into a register
- * @hba - per adapter instance
- * @mask - mask to apply on read value
- * @val - actual value to write
- * @reg - register address
- */
-static inline void ufshcd_rmwl(struct ufs_hba *hba, u32 mask, u32 val, u32 reg)
-{
- u32 tmp;
-
- tmp = ufshcd_readl(hba, reg);
- tmp &= ~mask;
- tmp |= (val & mask);
- ufshcd_writel(hba, tmp, reg);
-}
-
-int ufshcd_alloc_host(struct device *, struct ufs_hba **);
-int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int);
-void ufshcd_remove(struct ufs_hba *);
-
-/**
- * ufshcd_hba_stop - Send controller to reset state
- * @hba: per adapter instance
- */
-static inline void ufshcd_hba_stop(struct ufs_hba *hba)
-{
- ufshcd_writel(hba, CONTROLLER_DISABLE, REG_CONTROLLER_ENABLE);
-}
-
-static inline void check_upiu_size(void)
-{
- BUILD_BUG_ON(ALIGNED_UPIU_SIZE <
- GENERAL_UPIU_REQUEST_SIZE + QUERY_DESC_MAX_SIZE);
-}
-
-extern int ufshcd_runtime_suspend(struct ufs_hba *hba);
-extern int ufshcd_runtime_resume(struct ufs_hba *hba);
-extern int ufshcd_runtime_idle(struct ufs_hba *hba);
-extern int ufshcd_system_suspend(struct ufs_hba *hba);
-extern int ufshcd_system_resume(struct ufs_hba *hba);
-extern int ufshcd_shutdown(struct ufs_hba *hba);
-extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel,
- u8 attr_set, u32 mib_val, u8 peer);
-extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel,
- u32 *mib_val, u8 peer);
-
-/* UIC command interfaces for DME primitives */
-#define DME_LOCAL 0
-#define DME_PEER 1
-#define ATTR_SET_NOR 0 /* NORMAL */
-#define ATTR_SET_ST 1 /* STATIC */
-
-static inline int ufshcd_dme_set(struct ufs_hba *hba, u32 attr_sel,
- u32 mib_val)
-{
- return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR,
- mib_val, DME_LOCAL);
-}
-
-static inline int ufshcd_dme_st_set(struct ufs_hba *hba, u32 attr_sel,
- u32 mib_val)
-{
- return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST,
- mib_val, DME_LOCAL);
-}
-
-static inline int ufshcd_dme_peer_set(struct ufs_hba *hba, u32 attr_sel,
- u32 mib_val)
-{
- return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR,
- mib_val, DME_PEER);
-}
-
-static inline int ufshcd_dme_peer_st_set(struct ufs_hba *hba, u32 attr_sel,
- u32 mib_val)
-{
- return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST,
- mib_val, DME_PEER);
-}
-
-static inline int ufshcd_dme_get(struct ufs_hba *hba,
- u32 attr_sel, u32 *mib_val)
-{
- return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_LOCAL);
-}
-
-static inline int ufshcd_dme_peer_get(struct ufs_hba *hba,
- u32 attr_sel, u32 *mib_val)
-{
- return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER);
-}
-
-int ufshcd_hold(struct ufs_hba *hba, bool async);
-void ufshcd_release(struct ufs_hba *hba);
-#endif /* End of Header */
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
deleted file mode 100644
index 3fc3e21..0000000
--- a/drivers/scsi/ufs/unipro.h
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * drivers/scsi/ufs/unipro.h
- *
- * Copyright (C) 2013 Samsung Electronics Co., Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef _UNIPRO_H_
-#define _UNIPRO_H_
-
-/*
- * M-TX Configuration Attributes
- */
-#define TX_MODE 0x0021
-#define TX_HSRATE_SERIES 0x0022
-#define TX_HSGEAR 0x0023
-#define TX_PWMGEAR 0x0024
-#define TX_AMPLITUDE 0x0025
-#define TX_HS_SLEWRATE 0x0026
-#define TX_SYNC_SOURCE 0x0027
-#define TX_HS_SYNC_LENGTH 0x0028
-#define TX_HS_PREPARE_LENGTH 0x0029
-#define TX_LS_PREPARE_LENGTH 0x002A
-#define TX_HIBERN8_CONTROL 0x002B
-#define TX_LCC_ENABLE 0x002C
-#define TX_PWM_BURST_CLOSURE_EXTENSION 0x002D
-#define TX_BYPASS_8B10B_ENABLE 0x002E
-#define TX_DRIVER_POLARITY 0x002F
-#define TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE 0x0030
-#define TX_LS_TERMINATED_LINE_DRIVE_ENABLE 0x0031
-#define TX_LCC_SEQUENCER 0x0032
-#define TX_MIN_ACTIVATETIME 0x0033
-#define TX_PWM_G6_G7_SYNC_LENGTH 0x0034
-
-/*
- * M-RX Configuration Attributes
- */
-#define RX_MODE 0x00A1
-#define RX_HSRATE_SERIES 0x00A2
-#define RX_HSGEAR 0x00A3
-#define RX_PWMGEAR 0x00A4
-#define RX_LS_TERMINATED_ENABLE 0x00A5
-#define RX_HS_UNTERMINATED_ENABLE 0x00A6
-#define RX_ENTER_HIBERN8 0x00A7
-#define RX_BYPASS_8B10B_ENABLE 0x00A8
-#define RX_TERMINATION_FORCE_ENABLE 0x0089
-
-#define is_mphy_tx_attr(attr) (attr < RX_MODE)
-/*
- * PHY Adpater attributes
- */
-#define PA_ACTIVETXDATALANES 0x1560
-#define PA_ACTIVERXDATALANES 0x1580
-#define PA_TXTRAILINGCLOCKS 0x1564
-#define PA_PHY_TYPE 0x1500
-#define PA_AVAILTXDATALANES 0x1520
-#define PA_AVAILRXDATALANES 0x1540
-#define PA_MINRXTRAILINGCLOCKS 0x1543
-#define PA_TXPWRSTATUS 0x1567
-#define PA_RXPWRSTATUS 0x1582
-#define PA_TXFORCECLOCK 0x1562
-#define PA_TXPWRMODE 0x1563
-#define PA_LEGACYDPHYESCDL 0x1570
-#define PA_MAXTXSPEEDFAST 0x1521
-#define PA_MAXTXSPEEDSLOW 0x1522
-#define PA_MAXRXSPEEDFAST 0x1541
-#define PA_MAXRXSPEEDSLOW 0x1542
-#define PA_TXLINKSTARTUPHS 0x1544
-#define PA_TXSPEEDFAST 0x1565
-#define PA_TXSPEEDSLOW 0x1566
-#define PA_REMOTEVERINFO 0x15A0
-#define PA_TXGEAR 0x1568
-#define PA_TXTERMINATION 0x1569
-#define PA_HSSERIES 0x156A
-#define PA_PWRMODE 0x1571
-#define PA_RXGEAR 0x1583
-#define PA_RXTERMINATION 0x1584
-#define PA_MAXRXPWMGEAR 0x1586
-#define PA_MAXRXHSGEAR 0x1587
-#define PA_RXHSUNTERMCAP 0x15A5
-#define PA_RXLSTERMCAP 0x15A6
-#define PA_PACPREQTIMEOUT 0x1590
-#define PA_PACPREQEOBTIMEOUT 0x1591
-#define PA_HIBERN8TIME 0x15A7
-#define PA_LOCALVERINFO 0x15A9
-#define PA_TACTIVATE 0x15A8
-#define PA_PACPFRAMECOUNT 0x15C0
-#define PA_PACPERRORCOUNT 0x15C1
-#define PA_PHYTESTCONTROL 0x15C2
-#define PA_PWRMODEUSERDATA0 0x15B0
-#define PA_PWRMODEUSERDATA1 0x15B1
-#define PA_PWRMODEUSERDATA2 0x15B2
-#define PA_PWRMODEUSERDATA3 0x15B3
-#define PA_PWRMODEUSERDATA4 0x15B4
-#define PA_PWRMODEUSERDATA5 0x15B5
-#define PA_PWRMODEUSERDATA6 0x15B6
-#define PA_PWRMODEUSERDATA7 0x15B7
-#define PA_PWRMODEUSERDATA8 0x15B8
-#define PA_PWRMODEUSERDATA9 0x15B9
-#define PA_PWRMODEUSERDATA10 0x15BA
-#define PA_PWRMODEUSERDATA11 0x15BB
-#define PA_CONNECTEDTXDATALANES 0x1561
-#define PA_CONNECTEDRXDATALANES 0x1581
-#define PA_LOGICALLANEMAP 0x15A1
-#define PA_SLEEPNOCONFIGTIME 0x15A2
-#define PA_STALLNOCONFIGTIME 0x15A3
-#define PA_SAVECONFIGTIME 0x15A4
-
-/* PA power modes */
-enum {
- FAST_MODE = 1,
- SLOW_MODE = 2,
- FASTAUTO_MODE = 4,
- SLOWAUTO_MODE = 5,
- UNCHANGED = 7,
-};
-
-/* PA TX/RX Frequency Series */
-enum {
- PA_HS_MODE_A = 1,
- PA_HS_MODE_B = 2,
-};
-
-enum ufs_pwm_gear_tag {
- UFS_PWM_DONT_CHANGE, /* Don't change Gear */
- UFS_PWM_G1, /* PWM Gear 1 (default for reset) */
- UFS_PWM_G2, /* PWM Gear 2 */
- UFS_PWM_G3, /* PWM Gear 3 */
- UFS_PWM_G4, /* PWM Gear 4 */
- UFS_PWM_G5, /* PWM Gear 5 */
- UFS_PWM_G6, /* PWM Gear 6 */
- UFS_PWM_G7, /* PWM Gear 7 */
-};
-
-enum ufs_hs_gear_tag {
- UFS_HS_DONT_CHANGE, /* Don't change Gear */
- UFS_HS_G1, /* HS Gear 1 (default for reset) */
- UFS_HS_G2, /* HS Gear 2 */
- UFS_HS_G3, /* HS Gear 3 */
-};
-
-/*
- * Data Link Layer Attributes
- */
-#define DL_TC0TXFCTHRESHOLD 0x2040
-#define DL_FC0PROTTIMEOUTVAL 0x2041
-#define DL_TC0REPLAYTIMEOUTVAL 0x2042
-#define DL_AFC0REQTIMEOUTVAL 0x2043
-#define DL_AFC0CREDITTHRESHOLD 0x2044
-#define DL_TC0OUTACKTHRESHOLD 0x2045
-#define DL_TC1TXFCTHRESHOLD 0x2060
-#define DL_FC1PROTTIMEOUTVAL 0x2061
-#define DL_TC1REPLAYTIMEOUTVAL 0x2062
-#define DL_AFC1REQTIMEOUTVAL 0x2063
-#define DL_AFC1CREDITTHRESHOLD 0x2064
-#define DL_TC1OUTACKTHRESHOLD 0x2065
-#define DL_TXPREEMPTIONCAP 0x2000
-#define DL_TC0TXMAXSDUSIZE 0x2001
-#define DL_TC0RXINITCREDITVAL 0x2002
-#define DL_TC0TXBUFFERSIZE 0x2005
-#define DL_PEERTC0PRESENT 0x2046
-#define DL_PEERTC0RXINITCREVAL 0x2047
-#define DL_TC1TXMAXSDUSIZE 0x2003
-#define DL_TC1RXINITCREDITVAL 0x2004
-#define DL_TC1TXBUFFERSIZE 0x2006
-#define DL_PEERTC1PRESENT 0x2066
-#define DL_PEERTC1RXINITCREVAL 0x2067
-
-/*
- * Network Layer Attributes
- */
-#define N_DEVICEID 0x3000
-#define N_DEVICEID_VALID 0x3001
-#define N_TC0TXMAXSDUSIZE 0x3020
-#define N_TC1TXMAXSDUSIZE 0x3021
-
-/*
- * Transport Layer Attributes
- */
-#define T_NUMCPORTS 0x4000
-#define T_NUMTESTFEATURES 0x4001
-#define T_CONNECTIONSTATE 0x4020
-#define T_PEERDEVICEID 0x4021
-#define T_PEERCPORTID 0x4022
-#define T_TRAFFICCLASS 0x4023
-#define T_PROTOCOLID 0x4024
-#define T_CPORTFLAGS 0x4025
-#define T_TXTOKENVALUE 0x4026
-#define T_RXTOKENVALUE 0x4027
-#define T_LOCALBUFFERSPACE 0x4028
-#define T_PEERBUFFERSPACE 0x4029
-#define T_CREDITSTOSEND 0x402A
-#define T_CPORTMODE 0x402B
-#define T_TC0TXMAXSDUSIZE 0x4060
-#define T_TC1TXMAXSDUSIZE 0x4061
-
-/* Boolean attribute values */
-enum {
- FALSE = 0,
- TRUE,
-};
-
-#endif /* _UNIPRO_H_ */
diff --git a/include/linux/phy/phy-qcom-ufs.h b/include/linux/phy/phy-qcom-ufs.h
new file mode 100644
index 0000000..27f93a7
--- /dev/null
+++ b/include/linux/phy/phy-qcom-ufs.h
@@ -0,0 +1,205 @@
+/*
+ * Copyright (c) 2013-2014, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_H_
+#define UFS_QCOM_PHY_H_
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+#include <linux/scsi/ufs/ufshcd.h>
+#include <linux/scsi/ufs/unipro.h>
+#include <linux/scsi/ufs/ufs-qcom.h>
+
+#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \
+ { \
+ .reg_offset = reg, \
+ .cfg_value = val, \
+ }
+
+#define UFS_QCOM_PHY_NAME_LEN 30
+
+enum {
+ MASK_SERDES_START = 0x1,
+ MASK_PCS_READY = 0x1,
+};
+
+enum {
+ OFFSET_SERDES_START = 0x0,
+};
+
+struct ufs_qcom_phy_stored_attributes {
+ u32 att;
+ u32 value;
+};
+
+struct ufs_qcom_phy_calibration {
+ u32 reg_offset;
+ u32 cfg_value;
+};
+
+struct ufs_qcom_phy {
+ struct list_head list;
+ struct device *dev;
+ void __iomem *mmio;
+ void __iomem *dev_ref_clk_ctrl_mmio;
+ struct clk *tx_iface_clk;
+ struct clk *rx_iface_clk;
+ bool is_iface_clk_enabled;
+ struct clk *ref_clk_src;
+ struct clk *ref_clk_parent;
+ struct clk *ref_clk;
+ bool is_ref_clk_enabled;
+ bool is_dev_ref_clk_enabled;
+ struct ufs_qcom_phy_vreg vdda_pll;
+ struct ufs_qcom_phy_vreg vdda_phy;
+ struct ufs_qcom_phy_vreg vddp_ref_clk;
+ unsigned int quirks;
+ u8 host_ctrl_rev_major;
+ u16 host_ctrl_rev_minor;
+ u16 host_ctrl_rev_step;
+
+ /*
+ * As part of UFS power management, UFS link would be put in hibernate
+ * and UFS device would be put in SLEEP mode as part of runtime/system
+ * suspend callback. But when system goes into suspend with VDD
+ * minimization, UFS PHY states are being reset which means UFS link
+ * hibernate exit command on system resume would fail.
+ * If this quirk is enabled then above issue is workaround by saving
+ * the UFS PHY state information before system goes into suspend and
+ * restoring the saved state information during system resume but
+ * before executing the hibern8 exit command.
+ * Note that this quirk will help restoring the PHY state if even when
+ * link in not kept in hibern8 during suspend.
+ *
+ * Here is the list of steps to save/restore the configuration:
+ * Before entering into system suspend:
+ * 1. Read Critical PCS SWI Registers + less critical PHY CSR
+ * 2. Read RMMI Attributes
+ * Enter into system suspend
+ * After exiting from system suspend:
+ * 1. Set UFS_PHY_SOFT_RESET bit in UFS_CFG1 register of the UFS
+ * Controller
+ * 2. Write 0x01 to the UFS_PHY_POWER_DOWN_CONTROL register in the
+ * UFS PHY
+ * 3. Write back the values of the PHY SWI registers
+ * 4. Clear UFS_PHY_SOFT_RESET bit in UFS_CFG1 register of the UFS
+ * Controller
+ * 5. Write 0x01 to the UFS_PHY_PHY_START in the UFS PHY. This will
+ * start the PLL calibration and bring-up of the PHY.
+ * 6. Write back the values to the PHY RMMI Attributes
+ * 7. Wait for UFS_PHY_PCS_READY_STATUS[0] to be '1'
+ */
+ #define UFS_QCOM_PHY_QUIRK_CFG_RESTORE (1 << 0)
+
+ /*
+ * If UFS PHY power down is deasserted and power is restored to analog
+ * circuits, the rx_sigdet can glitch. If the glitch is wide enough,
+ * it can trigger the digital logic to think it saw a DIF-N and cause
+ * it to exit Hibern8. Disabling the rx_sigdet during power-up masks
+ * the glitch.
+ */
+ #define UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE (1 << 1)
+
+ /*
+ * If UFS link is put into Hibern8 and if UFS PHY analog hardware is
+ * power collapsed (by clearing UFS_PHY_POWER_DOWN_CONTROL), Hibern8
+ * exit might fail even after powering on UFS PHY analog hardware.
+ * Enabling this quirk will help to solve above issue by doing
+ * custom PHY settings just before PHY analog power collapse.
+ */
+ #define UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE (1 << 2)
+
+ char name[UFS_QCOM_PHY_NAME_LEN];
+ struct ufs_qcom_phy_calibration *cached_regs;
+ int cached_regs_table_size;
+ bool is_powered_on;
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops;
+};
+
+/**
+ * struct ufs_qcom_phy_specific_ops - set of pointers to functions which have a
+ * specific implementation per phy. Each UFS phy, should implement
+ * those functions according to its spec and requirements
+ * @calibrate_phy: pointer to a function that calibrate the phy
+ * @start_serdes: pointer to a function that starts the serdes
+ * @save_configuration: pointer to a function that saves phy
+ * configuration
+ * @is_physical_coding_sublayer_ready: pointer to a function that
+ * checks pcs readiness
+ * @set_tx_lane_enable: pointer to a function that enable tx lanes
+ * @power_control: pointer to a function that controls analog rail of phy
+ * and writes to QSERDES_RX_SIGDET_CNTRL attribute
+ */
+struct ufs_qcom_phy_specific_ops {
+ int (*calibrate_phy) (struct ufs_qcom_phy *phy);
+ void (*start_serdes) (struct ufs_qcom_phy *phy);
+ void (*save_configuration)(struct ufs_qcom_phy *phy);
+ void (*restore_configuration)(struct ufs_qcom_phy *phy);
+ int (*is_physical_coding_sublayer_ready) (struct ufs_qcom_phy *phy);
+ void (*set_tx_lane_enable) (struct ufs_qcom_phy *phy, u32 val);
+ void (*power_control) (struct ufs_qcom_phy *phy, bool val);
+};
+
+int ufs_qcom_phy_cfg_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg, bool on);
+int ufs_qcom_phy_enable_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg);
+int ufs_qcom_phy_disable_vreg(struct phy *phy,
+ struct ufs_qcom_phy_vreg *vreg);
+int ufs_qcom_phy_enable_ref_clk(struct phy *phy);
+void ufs_qcom_phy_disable_ref_clk(struct phy *phy);
+void ufs_qcom_phy_enable_dev_ref_clk(struct phy *);
+void ufs_qcom_phy_disable_dev_ref_clk(struct phy *);
+int ufs_qcom_phy_enable_iface_clk(struct phy *phy);
+void ufs_qcom_phy_disable_iface_clk(struct phy *phy);
+void ufs_qcom_phy_restore_swi_regs(struct phy *phy);
+int ufs_qcom_phy_link_startup_post_change(struct phy *phy,
+ struct ufs_hba *hba);
+int ufs_qcom_phy_base_init(struct platform_device *pdev,
+ struct ufs_qcom_phy *ufs_qcom_phy_ops);
+int ufs_qcom_phy_is_cfg_restore_quirk_enabled(struct phy *phy);
+struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy);
+int ufs_qcom_phy_start_serdes(struct phy *generic_phy);
+int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes);
+int ufs_qcom_phy_calibrate_phy(struct phy *generic_phy);
+int ufs_qcom_phy_is_pcs_ready(struct phy *generic_phy);
+int ufs_qcom_phy_save_configuration(struct phy *generic_phy);
+int ufs_qcom_phy_restore_configuration(struct phy *generic_phy);
+void ufs_qcom_phy_save_controller_version(struct phy *generic_phy,
+ u8 major, u16 minor, u16 step);
+int ufs_qcom_phy_power_on(struct phy *generic_phy);
+int ufs_qcom_phy_power_off(struct phy *generic_phy);
+int ufs_qcom_phy_exit(struct phy *generic_phy);
+int ufs_qcom_phy_init_clks(struct phy *generic_phy,
+ struct ufs_qcom_phy *phy_common);
+int ufs_qcom_phy_init_vregulators(struct phy *generic_phy,
+ struct ufs_qcom_phy *phy_common);
+int ufs_qcom_phy_remove(struct phy *generic_phy,
+ struct ufs_qcom_phy *ufs_qcom_phy);
+struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
+ struct ufs_qcom_phy *common_cfg,
+ struct phy_ops *ufs_qcom_phy_gen_ops,
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops);
+int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ struct ufs_qcom_phy_calibration *tbl_A, int tbl_size_A,
+ struct ufs_qcom_phy_calibration *tbl_B, int tbl_size_B,
+ int rate);
+#endif
diff --git a/include/linux/scsi/ufs/ufs-qcom.h b/include/linux/scsi/ufs/ufs-qcom.h
new file mode 100644
index 0000000..e38e997
--- /dev/null
+++ b/include/linux/scsi/ufs/ufs-qcom.h
@@ -0,0 +1,210 @@
+/* Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_H_
+#define UFS_QCOM_H_
+
+#include <linux/phy/phy.h>
+
+#define MAX_UFS_QCOM_HOSTS 1
+#define MAX_U32 (~(u32)0)
+#define MPHY_TX_FSM_STATE 0x41
+#define TX_FSM_HIBERN8 0x1
+#define HBRN8_POLL_TOUT_MS 100
+#define DEFAULT_CLK_RATE_HZ 1000000
+#define BUS_VECTOR_NAME_LEN 32
+
+#define UFS_HW_VER_MAJOR_SHFT (28)
+#define UFS_HW_VER_MAJOR_MASK (0x000F << UFS_HW_VER_MAJOR_SHFT)
+#define UFS_HW_VER_MINOR_SHFT (16)
+#define UFS_HW_VER_MINOR_MASK (0x0FFF << UFS_HW_VER_MINOR_SHFT)
+#define UFS_HW_VER_STEP_SHFT (0)
+#define UFS_HW_VER_STEP_MASK (0xFFFF << UFS_HW_VER_STEP_SHFT)
+
+/* vendor specific pre-defined parameters */
+#define SLOW 1
+#define FAST 2
+
+#define UFS_QCOM_LIMIT_NUM_LANES_RX 2
+#define UFS_QCOM_LIMIT_NUM_LANES_TX 2
+#define UFS_QCOM_LIMIT_HSGEAR_RX UFS_HS_G2
+#define UFS_QCOM_LIMIT_HSGEAR_TX UFS_HS_G2
+#define UFS_QCOM_LIMIT_PWMGEAR_RX UFS_PWM_G4
+#define UFS_QCOM_LIMIT_PWMGEAR_TX UFS_PWM_G4
+#define UFS_QCOM_LIMIT_RX_PWR_PWM SLOW_MODE
+#define UFS_QCOM_LIMIT_TX_PWR_PWM SLOW_MODE
+#define UFS_QCOM_LIMIT_RX_PWR_HS FAST_MODE
+#define UFS_QCOM_LIMIT_TX_PWR_HS FAST_MODE
+#define UFS_QCOM_LIMIT_HS_RATE PA_HS_MODE_B
+#define UFS_QCOM_LIMIT_DESIRED_MODE FAST
+
+/* QCOM UFS host controller vendor specific registers */
+enum {
+ REG_UFS_SYS1CLK_1US = 0xC0,
+ REG_UFS_TX_SYMBOL_CLK_NS_US = 0xC4,
+ REG_UFS_LOCAL_PORT_ID_REG = 0xC8,
+ REG_UFS_PA_ERR_CODE = 0xCC,
+ REG_UFS_RETRY_TIMER_REG = 0xD0,
+ REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8,
+ REG_UFS_CFG1 = 0xDC,
+ REG_UFS_CFG2 = 0xE0,
+ REG_UFS_HW_VERSION = 0xE4,
+
+ UFS_DBG_RD_REG_UAWM = 0x100,
+ UFS_DBG_RD_REG_UARM = 0x200,
+ UFS_DBG_RD_REG_TXUC = 0x300,
+ UFS_DBG_RD_REG_RXUC = 0x400,
+ UFS_DBG_RD_REG_DFC = 0x500,
+ UFS_DBG_RD_REG_TRLUT = 0x600,
+ UFS_DBG_RD_REG_TMRLUT = 0x700,
+ UFS_UFS_DBG_RD_REG_OCSC = 0x800,
+
+ UFS_UFS_DBG_RD_DESC_RAM = 0x1500,
+ UFS_UFS_DBG_RD_PRDT_RAM = 0x1700,
+ UFS_UFS_DBG_RD_RESP_RAM = 0x1800,
+ UFS_UFS_DBG_RD_EDTL_RAM = 0x1900,
+};
+
+/* bit definitions for REG_UFS_CFG2 register */
+#define UAWM_HW_CGC_EN (1 << 0)
+#define UARM_HW_CGC_EN (1 << 1)
+#define TXUC_HW_CGC_EN (1 << 2)
+#define RXUC_HW_CGC_EN (1 << 3)
+#define DFC_HW_CGC_EN (1 << 4)
+#define TRLUT_HW_CGC_EN (1 << 5)
+#define TMRLUT_HW_CGC_EN (1 << 6)
+#define OCSC_HW_CGC_EN (1 << 7)
+
+#define REG_UFS_CFG2_CGC_EN_ALL (UAWM_HW_CGC_EN | UARM_HW_CGC_EN |\
+ TXUC_HW_CGC_EN | RXUC_HW_CGC_EN |\
+ DFC_HW_CGC_EN | TRLUT_HW_CGC_EN |\
+ TMRLUT_HW_CGC_EN | OCSC_HW_CGC_EN)
+
+/* bit offset */
+enum {
+ OFFSET_UFS_PHY_SOFT_RESET = 1,
+ OFFSET_CLK_NS_REG = 10,
+};
+
+/* bit masks */
+enum {
+ MASK_UFS_PHY_SOFT_RESET = 0x2,
+ MASK_TX_SYMBOL_CLK_1US_REG = 0x3FF,
+ MASK_CLK_NS_REG = 0xFFFC00,
+};
+
+enum ufs_qcom_phy_init_type {
+ UFS_PHY_INIT_FULL,
+ UFS_PHY_INIT_CFG_RESTORE,
+};
+
+struct ufs_qcom_phy_vreg {
+ const char *name;
+ struct regulator *reg;
+ int max_uA;
+ int min_uV;
+ int max_uV;
+ bool enabled;
+ bool is_always_on;
+};
+
+static inline void
+ufs_qcom_get_controller_revision(struct ufs_hba *hba,
+ u8 *major, u16 *minor, u16 *step)
+{
+ u32 ver = ufshcd_readl(hba, REG_UFS_HW_VERSION);
+
+ *major = (ver & UFS_HW_VER_MAJOR_MASK) >> UFS_HW_VER_MAJOR_SHFT;
+ *minor = (ver & UFS_HW_VER_MINOR_MASK) >> UFS_HW_VER_MINOR_SHFT;
+ *step = (ver & UFS_HW_VER_STEP_MASK) >> UFS_HW_VER_STEP_SHFT;
+};
+
+static inline void ufs_qcom_assert_reset(struct ufs_hba *hba)
+{
+ ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET,
+ 1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1);
+ mb();
+}
+
+static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba)
+{
+ ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET,
+ 0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1);
+ mb();
+}
+
+struct ufs_qcom_bus_vote {
+ uint32_t client_handle;
+ uint32_t curr_vote;
+ int min_bw_vote;
+ int max_bw_vote;
+ int saved_vote;
+ bool is_max_bw_needed;
+ struct device_attribute max_bus_bw;
+};
+
+/**
+ * struct ufs_qcom_ice_data - ICE related information
+ * @vops: pointer to variant operations of ICE
+ * @async_done: completion for supporting ICE's driver asynchronous nature
+ * @pdev: pointer to the proper ICE platform device
+ * @state: UFS-ICE interface's internal state (see
+ * ufs-qcom-ice.h for possible internal states)
+ * @quirks: UFS-ICE interface related quirks
+ * @crypto_engine_err: crypto engine errors
+ */
+struct ufs_qcom_ice_data {
+ struct qcom_ice_variant_ops *vops;
+ struct completion async_done;
+ struct platform_device *pdev;
+ int state;
+
+ /*
+ * If UFS host controller should handle cryptographic engine's
+ * errors, enables this quirk.
+ */
+ #define UFS_QCOM_ICE_QUIRK_HANDLE_CRYPTO_ENGINE_ERRORS UFS_BIT(0)
+
+ u16 quirks;
+
+ bool crypto_engine_err;
+};
+
+struct ufs_qcom_host {
+ struct phy *generic_phy;
+ struct ufs_hba *hba;
+ struct ufs_qcom_bus_vote bus_vote;
+ struct ufs_pa_layer_attr dev_req_params;
+ struct clk *rx_l0_sync_clk;
+ struct clk *tx_l0_sync_clk;
+ struct clk *rx_l1_sync_clk;
+ struct clk *tx_l1_sync_clk;
+ bool is_lane_clks_enabled;
+ bool sec_cfg_updated;
+ struct ufs_qcom_ice_data ice;
+ u32 lanes_per_direction;
+};
+
+#define ufs_qcom_is_link_off(hba) ufshcd_is_link_off(hba)
+#define ufs_qcom_is_link_active(hba) ufshcd_is_link_active(hba)
+#define ufs_qcom_is_link_hibern8(hba) ufshcd_is_link_hibern8(hba)
+
+#define MAX_PROP_NAME 32
+#define VDDA_PHY_MIN_UV 1000000
+#define VDDA_PHY_MAX_UV 1000000
+#define VDDA_PLL_MIN_UV 1800000
+#define VDDA_PLL_MAX_UV 1800000
+#define VDDP_REF_CLK_MIN_UV 1200000
+#define VDDP_REF_CLK_MAX_UV 1200000
+
+#endif /* UFS_QCOM_H_ */
diff --git a/include/linux/scsi/ufs/ufs.h b/include/linux/scsi/ufs/ufs.h
new file mode 100644
index 0000000..42c459a
--- /dev/null
+++ b/include/linux/scsi/ufs/ufs.h
@@ -0,0 +1,491 @@
+/*
+ * Universal Flash Storage Host controller driver
+ *
+ * This code is based on drivers/scsi/ufs/ufs.h
+ * Copyright (C) 2011-2013 Samsung India Software Operations
+ *
+ * Authors:
+ * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx>
+ * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * See the COPYING file in the top-level directory or visit
+ * <http://www.gnu.org/licenses/gpl-2.0.html>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This program is provided "AS IS" and "WITH ALL FAULTS" and
+ * without warranty of any kind. You are solely responsible for
+ * determining the appropriateness of using and distributing
+ * the program and assume all risks associated with your exercise
+ * of rights with respect to the program, including but not limited
+ * to infringement of third party rights, the risks and costs of
+ * program errors, damage to or loss of data, programs or equipment,
+ * and unavailability or interruption of operations. Under no
+ * circumstances will the contributor of this Program be liable for
+ * any damages of any kind arising from your use or distribution of
+ * this program.
+ */
+
+#ifndef _UFS_H
+#define _UFS_H
+
+#include <linux/mutex.h>
+#include <linux/types.h>
+
+#define MAX_CDB_SIZE 16
+#define GENERAL_UPIU_REQUEST_SIZE 32
+#define QUERY_DESC_MAX_SIZE 255
+#define QUERY_DESC_MIN_SIZE 2
+#define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \
+ (sizeof(struct utp_upiu_header)))
+
+#define UPIU_HEADER_DWORD(byte3, byte2, byte1, byte0)\
+ cpu_to_be32((byte3 << 24) | (byte2 << 16) |\
+ (byte1 << 8) | (byte0))
+/*
+ * UFS device may have standard LUs and LUN id could be from 0x00 to
+ * 0x7F. Standard LUs use "Peripheral Device Addressing Format".
+ * UFS device may also have the Well Known LUs (also referred as W-LU)
+ * which again could be from 0x00 to 0x7F. For W-LUs, device only use
+ * the "Extended Addressing Format" which means the W-LUNs would be
+ * from 0xc100 (SCSI_W_LUN_BASE) onwards.
+ * This means max. LUN number reported from UFS device could be 0xC17F.
+ */
+#define UFS_UPIU_MAX_UNIT_NUM_ID 0x7F
+#define UFS_MAX_LUNS (SCSI_W_LUN_BASE + UFS_UPIU_MAX_UNIT_NUM_ID)
+#define UFS_UPIU_WLUN_ID (1 << 7)
+#define UFS_UPIU_MAX_GENERAL_LUN 8
+
+/* Well known logical unit id in LUN field of UPIU */
+enum {
+ UFS_UPIU_REPORT_LUNS_WLUN = 0x81,
+ UFS_UPIU_UFS_DEVICE_WLUN = 0xD0,
+ UFS_UPIU_BOOT_WLUN = 0xB0,
+ UFS_UPIU_RPMB_WLUN = 0xC4,
+};
+
+/*
+ * UFS Protocol Information Unit related definitions
+ */
+
+/* Task management functions */
+enum {
+ UFS_ABORT_TASK = 0x01,
+ UFS_ABORT_TASK_SET = 0x02,
+ UFS_CLEAR_TASK_SET = 0x04,
+ UFS_LOGICAL_RESET = 0x08,
+ UFS_QUERY_TASK = 0x80,
+ UFS_QUERY_TASK_SET = 0x81,
+};
+
+/* UTP UPIU Transaction Codes Initiator to Target */
+enum {
+ UPIU_TRANSACTION_NOP_OUT = 0x00,
+ UPIU_TRANSACTION_COMMAND = 0x01,
+ UPIU_TRANSACTION_DATA_OUT = 0x02,
+ UPIU_TRANSACTION_TASK_REQ = 0x04,
+ UPIU_TRANSACTION_QUERY_REQ = 0x16,
+};
+
+/* UTP UPIU Transaction Codes Target to Initiator */
+enum {
+ UPIU_TRANSACTION_NOP_IN = 0x20,
+ UPIU_TRANSACTION_RESPONSE = 0x21,
+ UPIU_TRANSACTION_DATA_IN = 0x22,
+ UPIU_TRANSACTION_TASK_RSP = 0x24,
+ UPIU_TRANSACTION_READY_XFER = 0x31,
+ UPIU_TRANSACTION_QUERY_RSP = 0x36,
+ UPIU_TRANSACTION_REJECT_UPIU = 0x3F,
+};
+
+/* UPIU Read/Write flags */
+enum {
+ UPIU_CMD_FLAGS_NONE = 0x00,
+ UPIU_CMD_FLAGS_WRITE = 0x20,
+ UPIU_CMD_FLAGS_READ = 0x40,
+};
+
+/* UPIU Task Attributes */
+enum {
+ UPIU_TASK_ATTR_SIMPLE = 0x00,
+ UPIU_TASK_ATTR_ORDERED = 0x01,
+ UPIU_TASK_ATTR_HEADQ = 0x02,
+ UPIU_TASK_ATTR_ACA = 0x03,
+};
+
+/* UPIU Query request function */
+enum {
+ UPIU_QUERY_FUNC_STANDARD_READ_REQUEST = 0x01,
+ UPIU_QUERY_FUNC_STANDARD_WRITE_REQUEST = 0x81,
+};
+
+/* Flag idn for Query Requests*/
+enum flag_idn {
+ QUERY_FLAG_IDN_FDEVICEINIT = 0x01,
+ QUERY_FLAG_IDN_PWR_ON_WPE = 0x03,
+ QUERY_FLAG_IDN_BKOPS_EN = 0x04,
+};
+
+/* Attribute idn for Query requests */
+enum attr_idn {
+ QUERY_ATTR_IDN_ACTIVE_ICC_LVL = 0x03,
+ QUERY_ATTR_IDN_BKOPS_STATUS = 0x05,
+ QUERY_ATTR_IDN_EE_CONTROL = 0x0D,
+ QUERY_ATTR_IDN_EE_STATUS = 0x0E,
+};
+
+/* Descriptor idn for Query requests */
+enum desc_idn {
+ QUERY_DESC_IDN_DEVICE = 0x0,
+ QUERY_DESC_IDN_CONFIGURAION = 0x1,
+ QUERY_DESC_IDN_UNIT = 0x2,
+ QUERY_DESC_IDN_RFU_0 = 0x3,
+ QUERY_DESC_IDN_INTERCONNECT = 0x4,
+ QUERY_DESC_IDN_STRING = 0x5,
+ QUERY_DESC_IDN_RFU_1 = 0x6,
+ QUERY_DESC_IDN_GEOMETRY = 0x7,
+ QUERY_DESC_IDN_POWER = 0x8,
+ QUERY_DESC_IDN_MAX,
+};
+
+enum desc_header_offset {
+ QUERY_DESC_LENGTH_OFFSET = 0x00,
+ QUERY_DESC_DESC_TYPE_OFFSET = 0x01,
+};
+
+enum ufs_desc_max_size {
+ QUERY_DESC_DEVICE_MAX_SIZE = 0x1F,
+ QUERY_DESC_CONFIGURAION_MAX_SIZE = 0x90,
+ QUERY_DESC_UNIT_MAX_SIZE = 0x23,
+ QUERY_DESC_INTERCONNECT_MAX_SIZE = 0x06,
+ /*
+ * Max. 126 UNICODE characters (2 bytes per character) plus 2 bytes
+ * of descriptor header.
+ */
+ QUERY_DESC_STRING_MAX_SIZE = 0xFE,
+ QUERY_DESC_GEOMETRY_MAZ_SIZE = 0x44,
+ QUERY_DESC_POWER_MAX_SIZE = 0x62,
+ QUERY_DESC_RFU_MAX_SIZE = 0x00,
+};
+
+/* Unit descriptor parameters offsets in bytes*/
+enum unit_desc_param {
+ UNIT_DESC_PARAM_LEN = 0x0,
+ UNIT_DESC_PARAM_TYPE = 0x1,
+ UNIT_DESC_PARAM_UNIT_INDEX = 0x2,
+ UNIT_DESC_PARAM_LU_ENABLE = 0x3,
+ UNIT_DESC_PARAM_BOOT_LUN_ID = 0x4,
+ UNIT_DESC_PARAM_LU_WR_PROTECT = 0x5,
+ UNIT_DESC_PARAM_LU_Q_DEPTH = 0x6,
+ UNIT_DESC_PARAM_MEM_TYPE = 0x8,
+ UNIT_DESC_PARAM_DATA_RELIABILITY = 0x9,
+ UNIT_DESC_PARAM_LOGICAL_BLK_SIZE = 0xA,
+ UNIT_DESC_PARAM_LOGICAL_BLK_COUNT = 0xB,
+ UNIT_DESC_PARAM_ERASE_BLK_SIZE = 0x13,
+ UNIT_DESC_PARAM_PROVISIONING_TYPE = 0x17,
+ UNIT_DESC_PARAM_PHY_MEM_RSRC_CNT = 0x18,
+ UNIT_DESC_PARAM_CTX_CAPABILITIES = 0x20,
+ UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1 = 0x22,
+};
+
+/*
+ * Logical Unit Write Protect
+ * 00h: LU not write protected
+ * 01h: LU write protected when fPowerOnWPEn =1
+ * 02h: LU permanently write protected when fPermanentWPEn =1
+ */
+enum ufs_lu_wp_type {
+ UFS_LU_NO_WP = 0x00,
+ UFS_LU_POWER_ON_WP = 0x01,
+ UFS_LU_PERM_WP = 0x02,
+};
+
+/* bActiveICCLevel parameter current units */
+enum {
+ UFSHCD_NANO_AMP = 0,
+ UFSHCD_MICRO_AMP = 1,
+ UFSHCD_MILI_AMP = 2,
+ UFSHCD_AMP = 3,
+};
+
+#define POWER_DESC_MAX_SIZE 0x62
+#define POWER_DESC_MAX_ACTV_ICC_LVLS 16
+
+/* Attribute bActiveICCLevel parameter bit masks definitions */
+#define ATTR_ICC_LVL_UNIT_OFFSET 14
+#define ATTR_ICC_LVL_UNIT_MASK (0x3 << ATTR_ICC_LVL_UNIT_OFFSET)
+#define ATTR_ICC_LVL_VALUE_MASK 0x3FF
+
+/* Power descriptor parameters offsets in bytes */
+enum power_desc_param_offset {
+ PWR_DESC_LEN = 0x0,
+ PWR_DESC_TYPE = 0x1,
+ PWR_DESC_ACTIVE_LVLS_VCC_0 = 0x2,
+ PWR_DESC_ACTIVE_LVLS_VCCQ_0 = 0x22,
+ PWR_DESC_ACTIVE_LVLS_VCCQ2_0 = 0x42,
+};
+
+/* Exception event mask values */
+enum {
+ MASK_EE_STATUS = 0xFFFF,
+ MASK_EE_URGENT_BKOPS = (1 << 2),
+};
+
+/* Background operation status */
+enum bkops_status {
+ BKOPS_STATUS_NO_OP = 0x0,
+ BKOPS_STATUS_NON_CRITICAL = 0x1,
+ BKOPS_STATUS_PERF_IMPACT = 0x2,
+ BKOPS_STATUS_CRITICAL = 0x3,
+ BKOPS_STATUS_MAX = BKOPS_STATUS_CRITICAL,
+};
+
+/* UTP QUERY Transaction Specific Fields OpCode */
+enum query_opcode {
+ UPIU_QUERY_OPCODE_NOP = 0x0,
+ UPIU_QUERY_OPCODE_READ_DESC = 0x1,
+ UPIU_QUERY_OPCODE_WRITE_DESC = 0x2,
+ UPIU_QUERY_OPCODE_READ_ATTR = 0x3,
+ UPIU_QUERY_OPCODE_WRITE_ATTR = 0x4,
+ UPIU_QUERY_OPCODE_READ_FLAG = 0x5,
+ UPIU_QUERY_OPCODE_SET_FLAG = 0x6,
+ UPIU_QUERY_OPCODE_CLEAR_FLAG = 0x7,
+ UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8,
+};
+
+/* Query response result code */
+enum {
+ QUERY_RESULT_SUCCESS = 0x00,
+ QUERY_RESULT_NOT_READABLE = 0xF6,
+ QUERY_RESULT_NOT_WRITEABLE = 0xF7,
+ QUERY_RESULT_ALREADY_WRITTEN = 0xF8,
+ QUERY_RESULT_INVALID_LENGTH = 0xF9,
+ QUERY_RESULT_INVALID_VALUE = 0xFA,
+ QUERY_RESULT_INVALID_SELECTOR = 0xFB,
+ QUERY_RESULT_INVALID_INDEX = 0xFC,
+ QUERY_RESULT_INVALID_IDN = 0xFD,
+ QUERY_RESULT_INVALID_OPCODE = 0xFE,
+ QUERY_RESULT_GENERAL_FAILURE = 0xFF,
+};
+
+/* UTP Transfer Request Command Type (CT) */
+enum {
+ UPIU_COMMAND_SET_TYPE_SCSI = 0x0,
+ UPIU_COMMAND_SET_TYPE_UFS = 0x1,
+ UPIU_COMMAND_SET_TYPE_QUERY = 0x2,
+};
+
+/* UTP Transfer Request Command Offset */
+#define UPIU_COMMAND_TYPE_OFFSET 28
+
+/* Offset of the response code in the UPIU header */
+#define UPIU_RSP_CODE_OFFSET 8
+
+enum {
+ MASK_SCSI_STATUS = 0xFF,
+ MASK_TASK_RESPONSE = 0xFF00,
+ MASK_RSP_UPIU_RESULT = 0xFFFF,
+ MASK_QUERY_DATA_SEG_LEN = 0xFFFF,
+ MASK_RSP_UPIU_DATA_SEG_LEN = 0xFFFF,
+ MASK_RSP_EXCEPTION_EVENT = 0x10000,
+};
+
+/* Task management service response */
+enum {
+ UPIU_TASK_MANAGEMENT_FUNC_COMPL = 0x00,
+ UPIU_TASK_MANAGEMENT_FUNC_NOT_SUPPORTED = 0x04,
+ UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED = 0x08,
+ UPIU_TASK_MANAGEMENT_FUNC_FAILED = 0x05,
+ UPIU_INCORRECT_LOGICAL_UNIT_NO = 0x09,
+};
+
+/* UFS device power modes */
+enum ufs_dev_pwr_mode {
+ UFS_ACTIVE_PWR_MODE = 1,
+ UFS_SLEEP_PWR_MODE = 2,
+ UFS_POWERDOWN_PWR_MODE = 3,
+};
+
+/**
+ * struct utp_upiu_header - UPIU header structure
+ * @dword_0: UPIU header DW-0
+ * @dword_1: UPIU header DW-1
+ * @dword_2: UPIU header DW-2
+ */
+struct utp_upiu_header {
+ __be32 dword_0;
+ __be32 dword_1;
+ __be32 dword_2;
+};
+
+/**
+ * struct utp_upiu_cmd - Command UPIU structure
+ * @data_transfer_len: Data Transfer Length DW-3
+ * @cdb: Command Descriptor Block CDB DW-4 to DW-7
+ */
+struct utp_upiu_cmd {
+ __be32 exp_data_transfer_len;
+ u8 cdb[MAX_CDB_SIZE];
+};
+
+/**
+ * struct utp_upiu_query - upiu request buffer structure for
+ * query request.
+ * @opcode: command to perform B-0
+ * @idn: a value that indicates the particular type of data B-1
+ * @index: Index to further identify data B-2
+ * @selector: Index to further identify data B-3
+ * @reserved_osf: spec reserved field B-4,5
+ * @length: number of descriptor bytes to read/write B-6,7
+ * @value: Attribute value to be written DW-5
+ * @reserved: spec reserved DW-6,7
+ */
+struct utp_upiu_query {
+ u8 opcode;
+ u8 idn;
+ u8 index;
+ u8 selector;
+ __be16 reserved_osf;
+ __be16 length;
+ __be32 value;
+ __be32 reserved[2];
+};
+
+/**
+ * struct utp_upiu_req - general upiu request structure
+ * @header:UPIU header structure DW-0 to DW-2
+ * @sc: fields structure for scsi command DW-3 to DW-7
+ * @qr: fields structure for query request DW-3 to DW-7
+ */
+struct utp_upiu_req {
+ struct utp_upiu_header header;
+ union {
+ struct utp_upiu_cmd sc;
+ struct utp_upiu_query qr;
+ };
+};
+
+/**
+ * struct utp_cmd_rsp - Response UPIU structure
+ * @residual_transfer_count: Residual transfer count DW-3
+ * @reserved: Reserved double words DW-4 to DW-7
+ * @sense_data_len: Sense data length DW-8 U16
+ * @sense_data: Sense data field DW-8 to DW-12
+ */
+struct utp_cmd_rsp {
+ __be32 residual_transfer_count;
+ __be32 reserved[4];
+ __be16 sense_data_len;
+ u8 sense_data[18];
+};
+
+/**
+ * struct utp_upiu_rsp - general upiu response structure
+ * @header: UPIU header structure DW-0 to DW-2
+ * @sr: fields structure for scsi command DW-3 to DW-12
+ * @qr: fields structure for query request DW-3 to DW-7
+ */
+struct utp_upiu_rsp {
+ struct utp_upiu_header header;
+ union {
+ struct utp_cmd_rsp sr;
+ struct utp_upiu_query qr;
+ };
+};
+
+/**
+ * struct utp_upiu_task_req - Task request UPIU structure
+ * @header - UPIU header structure DW0 to DW-2
+ * @input_param1: Input parameter 1 DW-3
+ * @input_param2: Input parameter 2 DW-4
+ * @input_param3: Input parameter 3 DW-5
+ * @reserved: Reserved double words DW-6 to DW-7
+ */
+struct utp_upiu_task_req {
+ struct utp_upiu_header header;
+ __be32 input_param1;
+ __be32 input_param2;
+ __be32 input_param3;
+ __be32 reserved[2];
+};
+
+/**
+ * struct utp_upiu_task_rsp - Task Management Response UPIU structure
+ * @header: UPIU header structure DW0-DW-2
+ * @output_param1: Ouput parameter 1 DW3
+ * @output_param2: Output parameter 2 DW4
+ * @reserved: Reserved double words DW-5 to DW-7
+ */
+struct utp_upiu_task_rsp {
+ struct utp_upiu_header header;
+ __be32 output_param1;
+ __be32 output_param2;
+ __be32 reserved[3];
+};
+
+/**
+ * struct ufs_query_req - parameters for building a query request
+ * @query_func: UPIU header query function
+ * @upiu_req: the query request data
+ */
+struct ufs_query_req {
+ u8 query_func;
+ struct utp_upiu_query upiu_req;
+};
+
+/**
+ * struct ufs_query_resp - UPIU QUERY
+ * @response: device response code
+ * @upiu_res: query response data
+ */
+struct ufs_query_res {
+ u8 response;
+ struct utp_upiu_query upiu_res;
+};
+
+#define UFS_VREG_VCC_MIN_UV 2700000 /* uV */
+#define UFS_VREG_VCC_MAX_UV 3600000 /* uV */
+#define UFS_VREG_VCC_1P8_MIN_UV 1700000 /* uV */
+#define UFS_VREG_VCC_1P8_MAX_UV 1950000 /* uV */
+#define UFS_VREG_VCCQ_MIN_UV 1100000 /* uV */
+#define UFS_VREG_VCCQ_MAX_UV 1300000 /* uV */
+#define UFS_VREG_VCCQ2_MIN_UV 1650000 /* uV */
+#define UFS_VREG_VCCQ2_MAX_UV 1950000 /* uV */
+
+/*
+ * VCCQ & VCCQ2 current requirement when UFS device is in sleep state
+ * and link is in Hibern8 state.
+ */
+#define UFS_VREG_LPM_LOAD_UA 1000 /* uA */
+
+struct ufs_vreg {
+ struct regulator *reg;
+ const char *name;
+ bool enabled;
+ int min_uV;
+ int max_uV;
+ int min_uA;
+ int max_uA;
+};
+
+struct ufs_vreg_info {
+ struct ufs_vreg *vcc;
+ struct ufs_vreg *vccq;
+ struct ufs_vreg *vccq2;
+ struct ufs_vreg *vdd_hba;
+};
+
+struct ufs_dev_info {
+ bool f_power_on_wp_en;
+ /* Keeps information if any of the LU is power on write protected */
+ bool is_lu_power_on_wp;
+};
+
+#endif /* End of Header */
diff --git a/include/linux/scsi/ufs/ufshcd.h b/include/linux/scsi/ufs/ufshcd.h
new file mode 100644
index 0000000..713723d
--- /dev/null
+++ b/include/linux/scsi/ufs/ufshcd.h
@@ -0,0 +1,654 @@
+/*
+ * Universal Flash Storage Host controller driver
+ *
+ * This code is based on drivers/scsi/ufs/ufshcd.h
+ * Copyright (C) 2011-2013 Samsung India Software Operations
+ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
+ *
+ * Authors:
+ * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx>
+ * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * See the COPYING file in the top-level directory or visit
+ * <http://www.gnu.org/licenses/gpl-2.0.html>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This program is provided "AS IS" and "WITH ALL FAULTS" and
+ * without warranty of any kind. You are solely responsible for
+ * determining the appropriateness of using and distributing
+ * the program and assume all risks associated with your exercise
+ * of rights with respect to the program, including but not limited
+ * to infringement of third party rights, the risks and costs of
+ * program errors, damage to or loss of data, programs or equipment,
+ * and unavailability or interruption of operations. Under no
+ * circumstances will the contributor of this Program be liable for
+ * any damages of any kind arising from your use or distribution of
+ * this program.
+ */
+
+#ifndef _UFSHCD_H
+#define _UFSHCD_H
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+#include <linux/errno.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/bitops.h>
+#include <linux/pm_runtime.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/regulator/consumer.h>
+
+#include <asm/irq.h>
+#include <asm/byteorder.h>
+#include <scsi/scsi.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_tcq.h>
+#include <scsi/scsi_dbg.h>
+#include <scsi/scsi_eh.h>
+
+#include "ufs.h"
+
+#define UFSHCD "ufshcd"
+#define UFSHCD_DRIVER_VERSION "0.2"
+
+struct ufs_hba;
+
+/**
+ * readl_poll_timeout - Periodically poll an address until a condition is met or a timeout occurs
+ * @addr: Address to poll
+ * @val: Variable to read the value into
+ * @cond: Break condition (usually involving @val)
+ * @sleep_us: Maximum time to sleep between reads in us (0 tight-loops)
+ * @timeout_us: Timeout in us, 0 means never timeout
+ *
+ * Returns 0 on success and -ETIMEDOUT upon a timeout. In either
+ * case, the last read value at @addr is stored in @val. Must not
+ * be called from atomic context if sleep_us or timeout_us are used.
+ */
+#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \
+({ \
+ ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \
+ might_sleep_if(timeout_us); \
+ for (;;) { \
+ (val) = readl(addr); \
+ if (cond) \
+ break; \
+ if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \
+ (val) = readl(addr); \
+ break; \
+ } \
+ if (sleep_us) \
+ usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \
+ } \
+ (cond) ? 0 : -ETIMEDOUT; \
+})
+
+enum dev_cmd_type {
+ DEV_CMD_TYPE_NOP = 0x0,
+ DEV_CMD_TYPE_QUERY = 0x1,
+};
+
+/**
+ * struct uic_command - UIC command structure
+ * @command: UIC command
+ * @argument1: UIC command argument 1
+ * @argument2: UIC command argument 2
+ * @argument3: UIC command argument 3
+ * @cmd_active: Indicate if UIC command is outstanding
+ * @result: UIC command result
+ * @done: UIC command completion
+ */
+struct uic_command {
+ u32 command;
+ u32 argument1;
+ u32 argument2;
+ u32 argument3;
+ int cmd_active;
+ int result;
+ struct completion done;
+};
+
+/* Used to differentiate the power management options */
+enum ufs_pm_op {
+ UFS_RUNTIME_PM,
+ UFS_SYSTEM_PM,
+ UFS_SHUTDOWN_PM,
+};
+
+#define ufshcd_is_runtime_pm(op) ((op) == UFS_RUNTIME_PM)
+#define ufshcd_is_system_pm(op) ((op) == UFS_SYSTEM_PM)
+#define ufshcd_is_shutdown_pm(op) ((op) == UFS_SHUTDOWN_PM)
+
+/* Host <-> Device UniPro Link state */
+enum uic_link_state {
+ UIC_LINK_OFF_STATE = 0, /* Link powered down or disabled */
+ UIC_LINK_ACTIVE_STATE = 1, /* Link is in Fast/Slow/Sleep state */
+ UIC_LINK_HIBERN8_STATE = 2, /* Link is in Hibernate state */
+};
+
+#define ufshcd_is_link_off(hba) ((hba)->uic_link_state == UIC_LINK_OFF_STATE)
+#define ufshcd_is_link_active(hba) ((hba)->uic_link_state == \
+ UIC_LINK_ACTIVE_STATE)
+#define ufshcd_is_link_hibern8(hba) ((hba)->uic_link_state == \
+ UIC_LINK_HIBERN8_STATE)
+#define ufshcd_set_link_off(hba) ((hba)->uic_link_state = UIC_LINK_OFF_STATE)
+#define ufshcd_set_link_active(hba) ((hba)->uic_link_state = \
+ UIC_LINK_ACTIVE_STATE)
+#define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \
+ UIC_LINK_HIBERN8_STATE)
+
+/*
+ * UFS Power management levels.
+ * Each level is in increasing order of power savings.
+ */
+enum ufs_pm_level {
+ UFS_PM_LVL_0, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_ACTIVE_STATE */
+ UFS_PM_LVL_1, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_HIBERN8_STATE */
+ UFS_PM_LVL_2, /* UFS_SLEEP_PWR_MODE, UIC_LINK_ACTIVE_STATE */
+ UFS_PM_LVL_3, /* UFS_SLEEP_PWR_MODE, UIC_LINK_HIBERN8_STATE */
+ UFS_PM_LVL_4, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_HIBERN8_STATE */
+ UFS_PM_LVL_5, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_OFF_STATE */
+ UFS_PM_LVL_MAX
+};
+
+struct ufs_pm_lvl_states {
+ enum ufs_dev_pwr_mode dev_state;
+ enum uic_link_state link_state;
+};
+
+/**
+ * struct ufshcd_lrb - local reference block
+ * @utr_descriptor_ptr: UTRD address of the command
+ * @ucd_req_ptr: UCD address of the command
+ * @ucd_rsp_ptr: Response UPIU address for this command
+ * @ucd_prdt_ptr: PRDT address of the command
+ * @cmd: pointer to SCSI command
+ * @sense_buffer: pointer to sense buffer address of the SCSI command
+ * @sense_bufflen: Length of the sense buffer
+ * @scsi_status: SCSI status of the command
+ * @command_type: SCSI, UFS, Query.
+ * @task_tag: Task tag of the command
+ * @lun: LUN of the command
+ * @intr_cmd: Interrupt command (doesn't participate in interrupt aggregation)
+ */
+struct ufshcd_lrb {
+ struct utp_transfer_req_desc *utr_descriptor_ptr;
+ struct utp_upiu_req *ucd_req_ptr;
+ struct utp_upiu_rsp *ucd_rsp_ptr;
+ struct ufshcd_sg_entry *ucd_prdt_ptr;
+
+ struct scsi_cmnd *cmd;
+ u8 *sense_buffer;
+ unsigned int sense_bufflen;
+ int scsi_status;
+
+ int command_type;
+ int task_tag;
+ u8 lun; /* UPIU LUN id field is only 8-bit wide */
+ bool intr_cmd;
+};
+
+/**
+ * struct ufs_query - holds relevent data structures for query request
+ * @request: request upiu and function
+ * @descriptor: buffer for sending/receiving descriptor
+ * @response: response upiu and response
+ */
+struct ufs_query {
+ struct ufs_query_req request;
+ u8 *descriptor;
+ struct ufs_query_res response;
+};
+
+/**
+ * struct ufs_dev_cmd - all assosiated fields with device management commands
+ * @type: device management command type - Query, NOP OUT
+ * @lock: lock to allow one command at a time
+ * @complete: internal commands completion
+ * @tag_wq: wait queue until free command slot is available
+ */
+struct ufs_dev_cmd {
+ enum dev_cmd_type type;
+ struct mutex lock;
+ struct completion *complete;
+ wait_queue_head_t tag_wq;
+ struct ufs_query query;
+};
+
+/**
+ * struct ufs_clk_info - UFS clock related info
+ * @list: list headed by hba->clk_list_head
+ * @clk: clock node
+ * @name: clock name
+ * @max_freq: maximum frequency supported by the clock
+ * @min_freq: min frequency that can be used for clock scaling
+ * @curr_freq: indicates the current frequency that it is set to
+ * @enabled: variable to check against multiple enable/disable
+ */
+struct ufs_clk_info {
+ struct list_head list;
+ struct clk *clk;
+ const char *name;
+ u32 max_freq;
+ u32 min_freq;
+ u32 curr_freq;
+ bool enabled;
+};
+
+#define PRE_CHANGE 0
+#define POST_CHANGE 1
+
+struct ufs_pa_layer_attr {
+ u32 gear_rx;
+ u32 gear_tx;
+ u32 lane_rx;
+ u32 lane_tx;
+ u32 pwr_rx;
+ u32 pwr_tx;
+ u32 hs_rate;
+};
+
+struct ufs_pwr_mode_info {
+ bool is_valid;
+ struct ufs_pa_layer_attr info;
+};
+
+/**
+ * struct ufs_hba_variant_ops - variant specific callbacks
+ * @name: variant name
+ * @init: called when the driver is initialized
+ * @exit: called to cleanup everything done in init
+ * @clk_scale_notify: notifies that clks are scaled up/down
+ * @setup_clocks: called before touching any of the controller registers
+ * @setup_regulators: called before accessing the host controller
+ * @hce_enable_notify: called before and after HCE enable bit is set to allow
+ * variant specific Uni-Pro initialization.
+ * @link_startup_notify: called before and after Link startup is carried out
+ * to allow variant specific Uni-Pro initialization.
+ * @pwr_change_notify: called before and after a power mode change
+ * is carried out to allow vendor spesific capabilities
+ * to be set.
+ * @suspend: called during host controller PM callback
+ * @resume: called during host controller PM callback
+ */
+struct ufs_hba_variant_ops {
+ const char *name;
+ int (*init)(struct ufs_hba *);
+ void (*exit)(struct ufs_hba *);
+ void (*clk_scale_notify)(struct ufs_hba *);
+ int (*setup_clocks)(struct ufs_hba *, bool);
+ int (*setup_regulators)(struct ufs_hba *, bool);
+ int (*hce_enable_notify)(struct ufs_hba *, bool);
+ int (*link_startup_notify)(struct ufs_hba *, bool);
+ int (*pwr_change_notify)(struct ufs_hba *,
+ bool, struct ufs_pa_layer_attr *,
+ struct ufs_pa_layer_attr *);
+ int (*suspend)(struct ufs_hba *, enum ufs_pm_op);
+ int (*resume)(struct ufs_hba *, enum ufs_pm_op);
+ int (*update_sec_cfg)(struct ufs_hba *hba, bool restore_sec_cfg);
+ int (*crypto_engine_cfg)(struct ufs_hba *, unsigned int);
+ int (*crypto_engine_eh)(struct ufs_hba *);
+ int (*crypto_engine_get_err)(struct ufs_hba *);
+ void (*crypto_engine_reset_err)(struct ufs_hba *);
+};
+
+/* clock gating state */
+enum clk_gating_state {
+ CLKS_OFF,
+ CLKS_ON,
+ REQ_CLKS_OFF,
+ REQ_CLKS_ON,
+};
+
+/**
+ * struct ufs_clk_gating - UFS clock gating related info
+ * @gate_work: worker to turn off clocks after some delay as specified in
+ * delay_ms
+ * @ungate_work: worker to turn on clocks that will be used in case of
+ * interrupt context
+ * @state: the current clocks state
+ * @delay_ms: gating delay in ms
+ * @is_suspended: clk gating is suspended when set to 1 which can be used
+ * during suspend/resume
+ * @delay_attr: sysfs attribute to control delay_attr
+ * @active_reqs: number of requests that are pending and should be waited for
+ * completion before gating clocks.
+ */
+struct ufs_clk_gating {
+ struct delayed_work gate_work;
+ struct work_struct ungate_work;
+ enum clk_gating_state state;
+ unsigned long delay_ms;
+ bool is_suspended;
+ struct device_attribute delay_attr;
+ int active_reqs;
+};
+
+struct ufs_clk_scaling {
+ ktime_t busy_start_t;
+ bool is_busy_started;
+ unsigned long tot_busy_t;
+ unsigned long window_start_t;
+};
+
+/**
+ * struct ufs_init_prefetch - contains data that is pre-fetched once during
+ * initialization
+ * @icc_level: icc level which was read during initialization
+ */
+struct ufs_init_prefetch {
+ u32 icc_level;
+};
+
+/**
+ * struct ufs_hba - per adapter private structure
+ * @mmio_base: UFSHCI base register address
+ * @ucdl_base_addr: UFS Command Descriptor base address
+ * @utrdl_base_addr: UTP Transfer Request Descriptor base address
+ * @utmrdl_base_addr: UTP Task Management Descriptor base address
+ * @ucdl_dma_addr: UFS Command Descriptor DMA address
+ * @utrdl_dma_addr: UTRDL DMA address
+ * @utmrdl_dma_addr: UTMRDL DMA address
+ * @host: Scsi_Host instance of the driver
+ * @dev: device handle
+ * @lrb: local reference block
+ * @lrb_in_use: lrb in use
+ * @outstanding_tasks: Bits representing outstanding task requests
+ * @outstanding_reqs: Bits representing outstanding transfer requests
+ * @capabilities: UFS Controller Capabilities
+ * @nutrs: Transfer Request Queue depth supported by controller
+ * @nutmrs: Task Management Queue depth supported by controller
+ * @ufs_version: UFS Version to which controller complies
+ * @vops: pointer to variant specific operations
+ * @priv: pointer to variant specific private data
+ * @irq: Irq number of the controller
+ * @active_uic_cmd: handle of active UIC command
+ * @uic_cmd_mutex: mutex for uic command
+ * @tm_wq: wait queue for task management
+ * @tm_tag_wq: wait queue for free task management slots
+ * @tm_slots_in_use: bit map of task management request slots in use
+ * @pwr_done: completion for power mode change
+ * @tm_condition: condition variable for task management
+ * @ufshcd_state: UFSHCD states
+ * @eh_flags: Error handling flags
+ * @intr_mask: Interrupt Mask Bits
+ * @ee_ctrl_mask: Exception event control mask
+ * @is_powered: flag to check if HBA is powered
+ * @is_init_prefetch: flag to check if data was pre-fetched in initialization
+ * @init_prefetch_data: data pre-fetched during initialization
+ * @eh_work: Worker to handle UFS errors that require s/w attention
+ * @eeh_work: Worker to handle exception events
+ * @errors: HBA errors
+ * @uic_error: UFS interconnect layer error status
+ * @saved_err: sticky error mask
+ * @saved_uic_err: sticky UIC error mask
+ * @dev_cmd: ufs device management command information
+ * @auto_bkops_enabled: to track whether bkops is enabled in device
+ * @vreg_info: UFS device voltage regulator information
+ * @clk_list_head: UFS host controller clocks list node head
+ * @pwr_info: holds current power mode
+ * @max_pwr_info: keeps the device max valid pwm
+ */
+struct ufs_hba {
+ void __iomem *mmio_base;
+
+ /* Virtual memory reference */
+ struct utp_transfer_cmd_desc *ucdl_base_addr;
+ struct utp_transfer_req_desc *utrdl_base_addr;
+ struct utp_task_req_desc *utmrdl_base_addr;
+
+ /* DMA memory reference */
+ dma_addr_t ucdl_dma_addr;
+ dma_addr_t utrdl_dma_addr;
+ dma_addr_t utmrdl_dma_addr;
+
+ struct Scsi_Host *host;
+ struct device *dev;
+ /*
+ * This field is to keep a reference to "scsi_device" corresponding to
+ * "UFS device" W-LU.
+ */
+ struct scsi_device *sdev_ufs_device;
+
+ enum ufs_dev_pwr_mode curr_dev_pwr_mode;
+ enum uic_link_state uic_link_state;
+ /* Desired UFS power management level during runtime PM */
+ enum ufs_pm_level rpm_lvl;
+ /* Desired UFS power management level during system PM */
+ enum ufs_pm_level spm_lvl;
+ int pm_op_in_progress;
+
+ struct ufshcd_lrb *lrb;
+ unsigned long lrb_in_use;
+
+ unsigned long outstanding_tasks;
+ unsigned long outstanding_reqs;
+
+ u32 capabilities;
+ int nutrs;
+ int nutmrs;
+ u32 ufs_version;
+ struct ufs_hba_variant_ops *vops;
+ void *priv;
+ unsigned int irq;
+ bool is_irq_enabled;
+
+ /* Interrupt aggregation support is broken */
+ #define UFSHCD_QUIRK_BROKEN_INTR_AGGR UFS_BIT(0)
+
+ /*
+ * delay before each dme command is required as the unipro
+ * layer has shown instabilities
+ */
+ #define UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS UFS_BIT(1)
+
+ /*
+ * If UFS host controller is having issue in processing LCC (Line
+ * Control Command) coming from device then enable this quirk.
+ * When this quirk is enabled, host controller driver should disable
+ * the LCC transmission on UFS device (by clearing TX_LCC_ENABLE
+ * attribute of device to 0).
+ */
+ #define UFSHCD_QUIRK_BROKEN_LCC UFS_BIT(2)
+
+ /*
+ * The attribute PA_RXHSUNTERMCAP specifies whether or not the
+ * inbound Link supports unterminated line in HS mode. Setting this
+ * attribute to 1 fixes moving to HS gear.
+ */
+ #define UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP UFS_BIT(3)
+
+ /*
+ * This quirk needs to be enabled if the host contoller only allows
+ * accessing the peer dme attributes in AUTO mode (FAST AUTO or
+ * SLOW AUTO).
+ */
+ #define UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE UFS_BIT(4)
+
+ unsigned int quirks; /* Deviations from standard UFSHCI spec. */
+
+ /* Device deviations from standard UFS device spec. */
+ unsigned int dev_quirks;
+
+ wait_queue_head_t tm_wq;
+ wait_queue_head_t tm_tag_wq;
+ unsigned long tm_condition;
+ unsigned long tm_slots_in_use;
+
+ struct uic_command *active_uic_cmd;
+ struct mutex uic_cmd_mutex;
+ struct completion *uic_async_done;
+
+ u32 ufshcd_state;
+ u32 eh_flags;
+ u32 intr_mask;
+ u16 ee_ctrl_mask;
+ bool is_powered;
+ bool is_init_prefetch;
+ struct ufs_init_prefetch init_prefetch_data;
+
+ /* Work Queues */
+ struct work_struct eh_work;
+ struct work_struct eeh_work;
+
+ /* HBA Errors */
+ u32 errors;
+ u32 uic_error;
+ u32 saved_err;
+ u32 saved_uic_err;
+
+ /* Device management request data */
+ struct ufs_dev_cmd dev_cmd;
+
+ /* Keeps information of the UFS device connected to this host */
+ struct ufs_dev_info dev_info;
+ bool auto_bkops_enabled;
+ struct ufs_vreg_info vreg_info;
+ struct list_head clk_list_head;
+
+ bool wlun_dev_clr_ua;
+
+ struct ufs_pa_layer_attr pwr_info;
+ struct ufs_pwr_mode_info max_pwr_info;
+
+ struct ufs_clk_gating clk_gating;
+ /* Control to enable/disable host capabilities */
+ u32 caps;
+ /* Allow dynamic clk gating */
+#define UFSHCD_CAP_CLK_GATING (1 << 0)
+ /* Allow hiberb8 with clk gating */
+#define UFSHCD_CAP_HIBERN8_WITH_CLK_GATING (1 << 1)
+ /* Allow dynamic clk scaling */
+#define UFSHCD_CAP_CLK_SCALING (1 << 2)
+ /* Allow auto bkops to enabled during runtime suspend */
+#define UFSHCD_CAP_AUTO_BKOPS_SUSPEND (1 << 3)
+
+ struct devfreq *devfreq;
+ struct ufs_clk_scaling clk_scaling;
+ bool is_sys_suspended;
+};
+
+/* Returns true if clocks can be gated. Otherwise false */
+static inline bool ufshcd_is_clkgating_allowed(struct ufs_hba *hba)
+{
+ return hba->caps & UFSHCD_CAP_CLK_GATING;
+}
+static inline bool ufshcd_can_hibern8_during_gating(struct ufs_hba *hba)
+{
+ return hba->caps & UFSHCD_CAP_HIBERN8_WITH_CLK_GATING;
+}
+static inline int ufshcd_is_clkscaling_enabled(struct ufs_hba *hba)
+{
+ return hba->caps & UFSHCD_CAP_CLK_SCALING;
+}
+static inline bool ufshcd_can_autobkops_during_suspend(struct ufs_hba *hba)
+{
+ return hba->caps & UFSHCD_CAP_AUTO_BKOPS_SUSPEND;
+}
+
+#define ufshcd_writel(hba, val, reg) \
+ writel((val), (hba)->mmio_base + (reg))
+#define ufshcd_readl(hba, reg) \
+ readl((hba)->mmio_base + (reg))
+
+/**
+ * ufshcd_rmwl - read modify write into a register
+ * @hba - per adapter instance
+ * @mask - mask to apply on read value
+ * @val - actual value to write
+ * @reg - register address
+ */
+static inline void ufshcd_rmwl(struct ufs_hba *hba, u32 mask, u32 val, u32 reg)
+{
+ u32 tmp;
+
+ tmp = ufshcd_readl(hba, reg);
+ tmp &= ~mask;
+ tmp |= (val & mask);
+ ufshcd_writel(hba, tmp, reg);
+}
+
+int ufshcd_alloc_host(struct device *, struct ufs_hba **);
+int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int);
+void ufshcd_remove(struct ufs_hba *);
+
+extern int ufshcd_runtime_suspend(struct ufs_hba *hba);
+extern int ufshcd_runtime_resume(struct ufs_hba *hba);
+extern int ufshcd_runtime_idle(struct ufs_hba *hba);
+extern int ufshcd_system_suspend(struct ufs_hba *hba);
+extern int ufshcd_system_resume(struct ufs_hba *hba);
+extern int ufshcd_shutdown(struct ufs_hba *hba);
+extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel,
+ u8 attr_set, u32 mib_val, u8 peer);
+extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel,
+ u32 *mib_val, u8 peer);
+
+/* UIC command interfaces for DME primitives */
+#define DME_LOCAL 0
+#define DME_PEER 1
+#define ATTR_SET_NOR 0 /* NORMAL */
+#define ATTR_SET_ST 1 /* STATIC */
+
+static inline int ufshcd_dme_set(struct ufs_hba *hba, u32 attr_sel,
+ u32 mib_val)
+{
+ return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR,
+ mib_val, DME_LOCAL);
+}
+
+static inline int ufshcd_dme_st_set(struct ufs_hba *hba, u32 attr_sel,
+ u32 mib_val)
+{
+ return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST,
+ mib_val, DME_LOCAL);
+}
+
+static inline int ufshcd_dme_peer_set(struct ufs_hba *hba, u32 attr_sel,
+ u32 mib_val)
+{
+ return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR,
+ mib_val, DME_PEER);
+}
+
+static inline int ufshcd_dme_peer_st_set(struct ufs_hba *hba, u32 attr_sel,
+ u32 mib_val)
+{
+ return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST,
+ mib_val, DME_PEER);
+}
+
+static inline int ufshcd_dme_get(struct ufs_hba *hba,
+ u32 attr_sel, u32 *mib_val)
+{
+ return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_LOCAL);
+}
+
+static inline int ufshcd_dme_peer_get(struct ufs_hba *hba,
+ u32 attr_sel, u32 *mib_val)
+{
+ return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER);
+}
+
+int ufshcd_hold(struct ufs_hba *hba, bool async);
+void ufshcd_release(struct ufs_hba *hba);
+void ufshcd_abort_outstanding_transfer_requests(struct ufs_hba *hba,
+ int result);
+#endif /* End of Header */
diff --git a/include/linux/scsi/ufs/unipro.h b/include/linux/scsi/ufs/unipro.h
new file mode 100644
index 0000000..3fc3e21
--- /dev/null
+++ b/include/linux/scsi/ufs/unipro.h
@@ -0,0 +1,207 @@
+/*
+ * drivers/scsi/ufs/unipro.h
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _UNIPRO_H_
+#define _UNIPRO_H_
+
+/*
+ * M-TX Configuration Attributes
+ */
+#define TX_MODE 0x0021
+#define TX_HSRATE_SERIES 0x0022
+#define TX_HSGEAR 0x0023
+#define TX_PWMGEAR 0x0024
+#define TX_AMPLITUDE 0x0025
+#define TX_HS_SLEWRATE 0x0026
+#define TX_SYNC_SOURCE 0x0027
+#define TX_HS_SYNC_LENGTH 0x0028
+#define TX_HS_PREPARE_LENGTH 0x0029
+#define TX_LS_PREPARE_LENGTH 0x002A
+#define TX_HIBERN8_CONTROL 0x002B
+#define TX_LCC_ENABLE 0x002C
+#define TX_PWM_BURST_CLOSURE_EXTENSION 0x002D
+#define TX_BYPASS_8B10B_ENABLE 0x002E
+#define TX_DRIVER_POLARITY 0x002F
+#define TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE 0x0030
+#define TX_LS_TERMINATED_LINE_DRIVE_ENABLE 0x0031
+#define TX_LCC_SEQUENCER 0x0032
+#define TX_MIN_ACTIVATETIME 0x0033
+#define TX_PWM_G6_G7_SYNC_LENGTH 0x0034
+
+/*
+ * M-RX Configuration Attributes
+ */
+#define RX_MODE 0x00A1
+#define RX_HSRATE_SERIES 0x00A2
+#define RX_HSGEAR 0x00A3
+#define RX_PWMGEAR 0x00A4
+#define RX_LS_TERMINATED_ENABLE 0x00A5
+#define RX_HS_UNTERMINATED_ENABLE 0x00A6
+#define RX_ENTER_HIBERN8 0x00A7
+#define RX_BYPASS_8B10B_ENABLE 0x00A8
+#define RX_TERMINATION_FORCE_ENABLE 0x0089
+
+#define is_mphy_tx_attr(attr) (attr < RX_MODE)
+/*
+ * PHY Adpater attributes
+ */
+#define PA_ACTIVETXDATALANES 0x1560
+#define PA_ACTIVERXDATALANES 0x1580
+#define PA_TXTRAILINGCLOCKS 0x1564
+#define PA_PHY_TYPE 0x1500
+#define PA_AVAILTXDATALANES 0x1520
+#define PA_AVAILRXDATALANES 0x1540
+#define PA_MINRXTRAILINGCLOCKS 0x1543
+#define PA_TXPWRSTATUS 0x1567
+#define PA_RXPWRSTATUS 0x1582
+#define PA_TXFORCECLOCK 0x1562
+#define PA_TXPWRMODE 0x1563
+#define PA_LEGACYDPHYESCDL 0x1570
+#define PA_MAXTXSPEEDFAST 0x1521
+#define PA_MAXTXSPEEDSLOW 0x1522
+#define PA_MAXRXSPEEDFAST 0x1541
+#define PA_MAXRXSPEEDSLOW 0x1542
+#define PA_TXLINKSTARTUPHS 0x1544
+#define PA_TXSPEEDFAST 0x1565
+#define PA_TXSPEEDSLOW 0x1566
+#define PA_REMOTEVERINFO 0x15A0
+#define PA_TXGEAR 0x1568
+#define PA_TXTERMINATION 0x1569
+#define PA_HSSERIES 0x156A
+#define PA_PWRMODE 0x1571
+#define PA_RXGEAR 0x1583
+#define PA_RXTERMINATION 0x1584
+#define PA_MAXRXPWMGEAR 0x1586
+#define PA_MAXRXHSGEAR 0x1587
+#define PA_RXHSUNTERMCAP 0x15A5
+#define PA_RXLSTERMCAP 0x15A6
+#define PA_PACPREQTIMEOUT 0x1590
+#define PA_PACPREQEOBTIMEOUT 0x1591
+#define PA_HIBERN8TIME 0x15A7
+#define PA_LOCALVERINFO 0x15A9
+#define PA_TACTIVATE 0x15A8
+#define PA_PACPFRAMECOUNT 0x15C0
+#define PA_PACPERRORCOUNT 0x15C1
+#define PA_PHYTESTCONTROL 0x15C2
+#define PA_PWRMODEUSERDATA0 0x15B0
+#define PA_PWRMODEUSERDATA1 0x15B1
+#define PA_PWRMODEUSERDATA2 0x15B2
+#define PA_PWRMODEUSERDATA3 0x15B3
+#define PA_PWRMODEUSERDATA4 0x15B4
+#define PA_PWRMODEUSERDATA5 0x15B5
+#define PA_PWRMODEUSERDATA6 0x15B6
+#define PA_PWRMODEUSERDATA7 0x15B7
+#define PA_PWRMODEUSERDATA8 0x15B8
+#define PA_PWRMODEUSERDATA9 0x15B9
+#define PA_PWRMODEUSERDATA10 0x15BA
+#define PA_PWRMODEUSERDATA11 0x15BB
+#define PA_CONNECTEDTXDATALANES 0x1561
+#define PA_CONNECTEDRXDATALANES 0x1581
+#define PA_LOGICALLANEMAP 0x15A1
+#define PA_SLEEPNOCONFIGTIME 0x15A2
+#define PA_STALLNOCONFIGTIME 0x15A3
+#define PA_SAVECONFIGTIME 0x15A4
+
+/* PA power modes */
+enum {
+ FAST_MODE = 1,
+ SLOW_MODE = 2,
+ FASTAUTO_MODE = 4,
+ SLOWAUTO_MODE = 5,
+ UNCHANGED = 7,
+};
+
+/* PA TX/RX Frequency Series */
+enum {
+ PA_HS_MODE_A = 1,
+ PA_HS_MODE_B = 2,
+};
+
+enum ufs_pwm_gear_tag {
+ UFS_PWM_DONT_CHANGE, /* Don't change Gear */
+ UFS_PWM_G1, /* PWM Gear 1 (default for reset) */
+ UFS_PWM_G2, /* PWM Gear 2 */
+ UFS_PWM_G3, /* PWM Gear 3 */
+ UFS_PWM_G4, /* PWM Gear 4 */
+ UFS_PWM_G5, /* PWM Gear 5 */
+ UFS_PWM_G6, /* PWM Gear 6 */
+ UFS_PWM_G7, /* PWM Gear 7 */
+};
+
+enum ufs_hs_gear_tag {
+ UFS_HS_DONT_CHANGE, /* Don't change Gear */
+ UFS_HS_G1, /* HS Gear 1 (default for reset) */
+ UFS_HS_G2, /* HS Gear 2 */
+ UFS_HS_G3, /* HS Gear 3 */
+};
+
+/*
+ * Data Link Layer Attributes
+ */
+#define DL_TC0TXFCTHRESHOLD 0x2040
+#define DL_FC0PROTTIMEOUTVAL 0x2041
+#define DL_TC0REPLAYTIMEOUTVAL 0x2042
+#define DL_AFC0REQTIMEOUTVAL 0x2043
+#define DL_AFC0CREDITTHRESHOLD 0x2044
+#define DL_TC0OUTACKTHRESHOLD 0x2045
+#define DL_TC1TXFCTHRESHOLD 0x2060
+#define DL_FC1PROTTIMEOUTVAL 0x2061
+#define DL_TC1REPLAYTIMEOUTVAL 0x2062
+#define DL_AFC1REQTIMEOUTVAL 0x2063
+#define DL_AFC1CREDITTHRESHOLD 0x2064
+#define DL_TC1OUTACKTHRESHOLD 0x2065
+#define DL_TXPREEMPTIONCAP 0x2000
+#define DL_TC0TXMAXSDUSIZE 0x2001
+#define DL_TC0RXINITCREDITVAL 0x2002
+#define DL_TC0TXBUFFERSIZE 0x2005
+#define DL_PEERTC0PRESENT 0x2046
+#define DL_PEERTC0RXINITCREVAL 0x2047
+#define DL_TC1TXMAXSDUSIZE 0x2003
+#define DL_TC1RXINITCREDITVAL 0x2004
+#define DL_TC1TXBUFFERSIZE 0x2006
+#define DL_PEERTC1PRESENT 0x2066
+#define DL_PEERTC1RXINITCREVAL 0x2067
+
+/*
+ * Network Layer Attributes
+ */
+#define N_DEVICEID 0x3000
+#define N_DEVICEID_VALID 0x3001
+#define N_TC0TXMAXSDUSIZE 0x3020
+#define N_TC1TXMAXSDUSIZE 0x3021
+
+/*
+ * Transport Layer Attributes
+ */
+#define T_NUMCPORTS 0x4000
+#define T_NUMTESTFEATURES 0x4001
+#define T_CONNECTIONSTATE 0x4020
+#define T_PEERDEVICEID 0x4021
+#define T_PEERCPORTID 0x4022
+#define T_TRAFFICCLASS 0x4023
+#define T_PROTOCOLID 0x4024
+#define T_CPORTFLAGS 0x4025
+#define T_TXTOKENVALUE 0x4026
+#define T_RXTOKENVALUE 0x4027
+#define T_LOCALBUFFERSPACE 0x4028
+#define T_PEERBUFFERSPACE 0x4029
+#define T_CREDITSTOSEND 0x402A
+#define T_CPORTMODE 0x402B
+#define T_TC0TXMAXSDUSIZE 0x4060
+#define T_TC1TXMAXSDUSIZE 0x4061
+
+/* Boolean attribute values */
+enum {
+ FALSE = 0,
+ TRUE,
+};
+
+#endif /* _UNIPRO_H_ */
--
1.8.5.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
