Currently the DWC3 driver supports only single port controller which requires at most two PHYs ie HS and SS PHYs. There are SoCs that has DWC3 controller with multiple ports that can operate in host mode. Some of the port supports both SS+HS and other port supports only HS mode. This change primarily refactors the Phy logic in core driver to allow multiport support with Generic Phy's. Chananges have been tested on QCOM SoC SA8295P which has 4 ports (2 are HS+SS capable and 2 are HS only capable). Changes in v8: Reorganised code in patch-5 Fixed nitpicks in code according to comments received on v7 Fixed indentation in DT patches Added drive strength for pinctrl nodes in SA8295 DT Changes in v7: Added power event irq's for Multiport controller. Udpated commit text for patch-9 (adding DT changes for enabling first port of multiport controller on sa8540-ride). Fixed check-patch warnings for driver code. Fixed DT binding errors for changes in snps,dwc3.yaml Reabsed code on top of usb-next Changes in v6: Updated comments in code after. Updated variables names appropriately as per review comments. Updated commit text in patch-2 and added additional info as per review comments. The patch header in v5 doesn't have "PATHCH v5" notation present. Corrected it in this version. Changes in v5: Added DT support for first port of Teritiary USB controller on SA8540-Ride Added support for reading port info from XHCI Extended Params registers. Changes in RFC v4: Added DT support for SA8295p. Changes in RFC v3: Incase any PHY init fails, then clear/exit the PHYs that are already initialized. Changes in RFC v2: Changed dwc3_count_phys to return the number of PHY Phandles in the node. This will be used now in dwc3_extract_num_phys to increment num_usb2_phy and num_usb3_phy. Added new parameter "ss_idx" in dwc3_core_get_phy_ny_node and changed its structure such that the first half is for HS-PHY and second half is for SS-PHY. In dwc3_core_get_phy, for multiport controller, only if SS-PHY phandle is present, pass proper SS_IDX else pass -1. Link to v7: https://lore.kernel.org/all/20230501143445.3851-1-quic_kriskura@xxxxxxxxxxx/ Link to v6: https://lore.kernel.org/all/20230405125759.4201-1-quic_kriskura@xxxxxxxxxxx/ Link to v5: https://lore.kernel.org/all/20230310163420.7582-1-quic_kriskura@xxxxxxxxxxx/ Link to RFC v4: https://lore.kernel.org/all/20230115114146.12628-1-quic_kriskura@xxxxxxxxxxx/ Link to RFC v3: https://lore.kernel.org/all/1654709787-23686-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r Link to RFC v2: https://lore.kernel.org/all/1653560029-6937-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r Test results: Bus 3/4 represent multiport controller having 4 HS ports and 2 SS ports. / # dmesg |grep hub [ 0.029029] usbcore: registered new interface driver hub [ 1.372812] hub 1-0:1.0: USB hub found [ 1.389142] hub 1-0:1.0: 1 port detected [ 1.414721] hub 2-0:1.0: USB hub found [ 1.427669] hub 2-0:1.0: 1 port detected [ 2.931465] hub 3-0:1.0: USB hub found [ 2.935340] hub 3-0:1.0: 4 ports detected [ 2.948721] hub 4-0:1.0: USB hub found [ 2.952604] hub 4-0:1.0: 2 ports detected / # / # lsusb Bus 003 Device 001: ID 1d6b:0002 Bus 001 Device 001: ID 1d6b:0002 Bus 003 Device 005: ID 0b0e:0300 Bus 003 Device 002: ID 046d:c077 Bus 004 Device 001: ID 1d6b:0003 Bus 002 Device 001: ID 1d6b:0003 Bus 003 Device 004: ID 03f0:0024 Bus 003 Device 003: ID 046d:c016 Krishna Kurapati (9): dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport dt-bindings: usb: Add bindings for multiport properties on DWC3 controller usb: dwc3: core: Access XHCI address space temporarily to read port info usb: dwc3: core: Skip setting event buffers for host only controllers usb: dwc3: core: Refactor PHY logic to support Multiport Controller usb: dwc3: qcom: Add multiport controller support for qcom wrapper arm64: dts: qcom: sc8280xp: Add multiport controller node for SC8280 arm64: dts: qcom: sa8295p: Enable tertiary controller and its 4 USB ports arm64: dts: qcom: sa8540-ride: Enable first port of tertiary usb controller .../devicetree/bindings/usb/qcom,dwc3.yaml | 22 + .../devicetree/bindings/usb/snps,dwc3.yaml | 13 +- arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 52 +++ arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 + arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 66 +++ drivers/usb/dwc3/core.c | 389 +++++++++++++++--- drivers/usb/dwc3/core.h | 28 +- drivers/usb/dwc3/drd.c | 13 +- drivers/usb/dwc3/dwc3-qcom.c | 28 +- 9 files changed, 543 insertions(+), 90 deletions(-) -- 2.40.0
