Hello Neil,
I apologize for the delayed response, as I did not have access to my laptop
for a few days.
On Tue, May 09, 2023 at 09:44:33AM +0200, neil.armstrong@xxxxxxxxxx wrote:
> Hi,
>
> On 26/04/2023 12:29, Dmitry Rokosov wrote:
> > Amlogic A1 SoC family has USB2.0 controller based on dwc2 and dwc3
> > heads. It supports otg/host/peripheral modes.
> >
> > Signed-off-by: Yue Wang <yue.wang@xxxxxxxxxxx>
> > Signed-off-by: Hanjie Lin <hanjie.lin@xxxxxxxxxxx>
> > Signed-off-by: Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 59 +++++++++++++++++++++++
> > 1 file changed, 59 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > index ae7d39cff07a..5588ee602161 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > @@ -8,6 +8,8 @@
> > #include <dt-bindings/gpio/meson-a1-gpio.h>
> > #include <dt-bindings/clock/amlogic,a1-pll-clkc.h>
> > #include <dt-bindings/clock/amlogic,a1-clkc.h>
> > +#include <dt-bindings/power/meson-a1-power.h>
> > +#include <dt-bindings/reset/amlogic,meson-a1-reset.h>
> > / {
> > compatible = "amlogic,a1";
> > @@ -169,6 +171,17 @@ gpio_intc: interrupt-controller@0440 {
> > amlogic,channel-interrupts =
> > <49 50 51 52 53 54 55 56>;
> > };
> > +
> > + usb2_phy1: phy@4000 {
> > + compatible = "amlogic,a1-usb2-phy";
> > + clocks = <&clkc CLKID_USB_PHY_IN>;
> > + clock-names = "xtal";
> > + reg = <0x0 0x4000 0x0 0x60>;
> > + resets = <&reset RESET_USBPHY>;
> > + reset-names = "phy";
> > + #phy-cells = <0>;
> > + power-domains = <&pwrc PWRC_USB_ID>;
> > + };
> > };
> > gic: interrupt-controller@ff901000 {
> > @@ -192,6 +205,52 @@ spifc: spi@fd000400 {
> > #size-cells = <0>;
> > status = "disabled";
> > };
> > +
> > + usb: usb@fe004400 {
> > + status = "disabled";
> > + compatible = "amlogic,meson-a1-usb-ctrl";
> > + reg = <0x0 0xfe004400 0x0 0xa0>;
> > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + clocks = <&clkc CLKID_USB_CTRL>,
> > + <&clkc CLKID_USB_BUS>,
> > + <&clkc CLKID_USB_CTRL_IN>;
> > + clock-names = "usb_ctrl", "usb_bus", "xtal_usb_ctrl";
> > + resets = <&reset RESET_USBCTRL>;
> > + reset-name = "usb_ctrl";
> > +
> > + dr_mode = "otg";
> > +
> > + phys = <&usb2_phy1>;
> > + phy-names = "usb2-phy1";
> > +
> > + dwc2: usb@ff500000 {
> > + compatible = "amlogic,meson-a1-usb", "snps,dwc2";
> > + reg = <0x0 0xff500000 0x0 0x40000>;
> > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> > + phys = <&usb2_phy1>;
> > + phy-names = "usb2-phy";
> > + clocks = <&clkc CLKID_USB_PHY>;
> > + clock-names = "otg";
> > + dr_mode = "peripheral";
> > + g-rx-fifo-size = <192>;
> > + g-np-tx-fifo-size = <128>;
> > + g-tx-fifo-size = <128 128 16 16 16>;
> > + };
> > +
> > + dwc3: usb@ff400000 {
> > + compatible = "snps,dwc3";
> > + reg = <0x0 0xff400000 0x0 0x100000>;
> > + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
> > + dr_mode = "host";
> > + snps,dis_u2_susphy_quirk;
> > + snps,quirk-frame-length-adjustment = <0x20>;
> > + snps,parkmode-disable-ss-quirk;
> > + };
> > + };
> > };
> > timer {
>
> This patcj is fine, but depends on clock bindings & dt, so now Vinod took the PHY
> patch, please resend this wiyhout patches 1 & 5, then resend the DT patch later when
> the clock bindings is merged.
>
> Thanks,
> Neil
Sure, not a problem. I will resend the 3 patchsets in different series.
--
Thank you,
Dmitry
