Re: [PATCH v3 2/3] dt-bindings: Add pinctrl bindings for mt65xx/mt81xx.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, Nov 11, 2014 at 1:38 PM, Hongzhou Yang
<hongzhou.yang@xxxxxxxxxxxx> wrote:

> +* Mediatek MT65XX Pin Controller
> +
> +The Mediatek's Pin controller is used to control GPIO pins.

It's not GPIO pins, since they are not always general purpose. It's just
pins. Say "control SoC pins".

> +Required properties:
> +- compatible: value should be either of the following.
> +    (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
> +- mediatek,pctl-regmap: Should be a phandle of the syscfg node.
> +- gpio-controller : Marks the device node as a gpio controller.
> +- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
> +  binding is used, the amount of cells must be specified as 2. See the below
> +  mentioned gpio binding representation for description of particular cells.
> +
> +       Eg: <&pio 6 0>
> +       <[phandle of the gpio controller node]
> +       [pin number within the gpio controller]

It's not a pin number really, it is a GPIO offset. But incidentally it's
the same as the pin number. (This is OK...)

> +- mediatek,pins: 2 integers array, represents gpio pinmux number and config
> +  setting. The format as following
> +
> +    node {
> +     mediatek,pins = <PIN_NUMBER_PINMUX>;
> +                     GENERIC_PINCONFIG;
> +    };

As suggested by Sacha, use just "pins" and define the binding as a patch
to Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
that is generic for multiplexing, so we get some order here.

I want you however to put pin multiplexing and pin configuration into
different nodes if possible. I don't like combines muxing and config
nodes. If necessary tag the node with something.

In the end we can also move the parsing functions to the pinctrl core, as
long as the bindings are correct (possibly as a refactoring later).

> +               i2c0_pins_a: i2c0@0 {
> +                       pins1 {
> +                               mediatek,pins = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
> +                                               <MT8135_PIN_101_SCL0__FUNC_SCL0>;
> +                               bias-disable;
> +                       };
> +               };

I would split it up.

i2c0_pins_a: i2c0@0 {
        pins1 {
                pins = <MT8135_PIN_100_SDA0>;
                function = <MT8135_PIN_100_FUNC_SDA0>;
        };
        pins2 {
               pins = <MT8135_PIN_100_SDA0>;
               bias-disable;
        };
};

One node for the multiplexing, one node for the config. This is the
pattern used by most drivers, so I want to have this structure.

It is also easy to tell one node from the other: if it contains "function"
we know it's a multiplexing node, if it doesn't, it's a config node.

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux