On 11/05/2023 19:10, Tim Harvey wrote:
> The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
>
> The GW702x SOM contains the following:
> - i.MX8M Plus SoC
> - LPDDR4 memory
> - eMMC Boot device
> - Gateworks System Controller (GSC) with integrated EEPROM, button
> controller, and ADC's
> - PMIC
> - RGMII PHY (eQoS)
> - SOM connector providing:
> - eQoS GbE MII
> - 1x SPI
> - 2x I2C
> - 4x UART
> - 2x USB 3.0
> - 1x PCI
> - 1x SDIO (4-bit 3.3V)
> - 1x SDIO (4-bit 3.3V/1.8V)
> - GPIO
>
> The GW7905 Baseboard contains the following:
> - GPS
> - microSD
> - off-board I/O connector with I2C, SPI, GPIO
> - EERPOM
> - PCIe clock generator
> - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
> - 1x half-length miniPCIe socket with USB2.0 and USB3.0
> - USB 3.0 HUB
> - USB Type-C with USB PD Sink capability and peripheral support
> - USB Type-C with USB 3.0 host support
>
> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
> ---
> .../dts/freescale/imx8mp-venice-gw702x.dtsi | 589 ++++++++++++++++++
> .../dts/freescale/imx8mp-venice-gw7905-2x.dts | 28 +
> .../dts/freescale/imx8mp-venice-gw7905.dtsi | 358 +++++++++++
How do you compile it? Missing Makefile. This also suggests that maybe
you did not test it with dtbs_check...
> 3 files changed, 975 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
...
> + gsc: gsc@20 {
> + compatible = "gw,gsc";
> + reg = <0x20>;
> + pinctrl-0 = <&pinctrl_gsc>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + adc {
> + compatible = "gw,gsc-adc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@6 {
> + gw,mode = <0>;
> + reg = <0x06>;
> + label = "temp";
> + };
> +
> + channel@8 {
> + gw,mode = <1>;
> + reg = <0x08>;
> + label = "vdd_bat";
> + };
> +
> + channel@16 {
> + gw,mode = <4>;
> + reg = <0x16>;
> + label = "fan_tach";
> + };
> +
> + channel@82 {
> + gw,mode = <2>;
> + reg = <0x82>;
> + label = "vdd_vin";
> + gw,voltage-divider-ohms = <22100 1000>;
> + };
> +
> + channel@84 {
> + gw,mode = <2>;
> + reg = <0x84>;
> + label = "vdd_adc1";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel@86 {
> + gw,mode = <2>;
> + reg = <0x86>;
> + label = "vdd_adc2";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel@88 {
> + gw,mode = <2>;
> + reg = <0x88>;
> + label = "vdd_1p0";
> + };
> +
> + channel@8c {
> + gw,mode = <2>;
> + reg = <0x8c>;
> + label = "vdd_1p8";
> + };
> +
> + channel@8e {
> + gw,mode = <2>;
> + reg = <0x8e>;
> + label = "vdd_2p5";
> + };
> +
> + channel@90 {
> + gw,mode = <2>;
> + reg = <0x90>;
> + label = "vdd_3p3";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel@92 {
> + gw,mode = <2>;
> + reg = <0x92>;
> + label = "vdd_dram";
> + };
> +
> + channel@98 {
> + gw,mode = <2>;
> + reg = <0x98>;
> + label = "vdd_soc";
> + };
> +
> + channel@9a {
> + gw,mode = <2>;
> + reg = <0x9a>;
> + label = "vdd_arm";
> + };
> +
> + channel@a2 {
> + gw,mode = <2>;
> + reg = <0xa2>;
> + label = "vdd_gsc";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> + };
> +
> + fan-controller@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
Why do you need these two? I know binding expects them, but why? Anyway
compatible is first, reg is second property.
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> new file mode 100644
> index 000000000000..4a1bbbbe19e6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> @@ -0,0 +1,28 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp.dtsi"
> +#include "imx8mp-venice-gw702x.dtsi"
> +#include "imx8mp-venice-gw7905.dtsi"
> +
> +/ {
> + model = "Gateworks Venice GW7905-2x i.MX8MP Development Kit";
> + compatible = "gateworks,imx8mp-gw7905-2x", "fsl,imx8mp";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +};
> +
> +/* Disable SOM interfaces not used on baseboard */
> +&eqos {
> + status = "disabled";
> +};
> +
> +&usdhc1 {
> + status = "disabled";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> new file mode 100644
> index 000000000000..479190a6391f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> @@ -0,0 +1,358 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +/ {
> + aliases {
> + ethernet0 = &eqos;
> + };
> +
> + led-controller {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> + led-0 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-1 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_RED>;
> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
> +
> + pcie0_refclk: pcie0-refclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + };
> +
> + pps {
> + compatible = "pps-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pps>;
> + gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
> +
> + reg_usb2_vbus: regulator-usb2-vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usb2_en>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb2_vbus";
> + gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + compatible = "regulator-fixed";
> + regulator-name = "SD2_3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
Drop stay blank line
> +};
> +
> +/* off-board header */
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi2>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
Best regards,
Krzysztof
