Convert the NAU8825 audio CODEC bindings to DT schema.
Signed-off-by: David Lin <CTLIN0@xxxxxxxxxxx>
Changes:
V3 -> V4:
- remove the description from interrupts, clocks and clock-names properites
- add sound-dai-cells property and update the dts example
V2 -> V3:
- refine node name from "nau8825" to "codec" for generic purpose
V1 -> V2:
- add interrupts properties
- add maximum to nuvoton,jack-insert-debounce and nuvoton,jack-eject-debounce properites
- add a enum item for nuvoton,short-key-debounce properites
- add default value for most properites
- add maxItems to clocks properites and mclk entries to clock-names properites
- refine wrong indentation from clocks and clock-names
- refine dts example for interrupts and clocks
- remove headset label from dts example
---
.../devicetree/bindings/sound/nau8825.txt | 111 --------
.../bindings/sound/nuvoton,nau8825.yaml | 239 ++++++++++++++++++
2 files changed, 239 insertions(+), 111 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt
create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml
diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt
deleted file mode 100644
index a9c34526f4cb..000000000000
--- a/Documentation/devicetree/bindings/sound/nau8825.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-Nuvoton NAU8825 audio codec
-
-This device supports I2C only.
-
-Required properties:
- - compatible : Must be "nuvoton,nau8825"
-
- - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
-
-Optional properties:
- - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
- - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
- otherwise pin in high impedance state.
- - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
- - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
-
- - nuvoton,vref-impedance: VREF Impedance selection
- 0 - Open
- 1 - 25 kOhm
- 2 - 125 kOhm
- 3 - 2.5 kOhm
-
- - nuvoton,micbias-voltage: Micbias voltage level.
- 0 - VDDA
- 1 - VDDA
- 2 - VDDA * 1.1
- 3 - VDDA * 1.2
- 4 - VDDA * 1.3
- 5 - VDDA * 1.4
- 6 - VDDA * 1.53
- 7 - VDDA * 1.53
-
- - nuvoton,sar-threshold-num: Number of buttons supported
- - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
- SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
- where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
- Refer datasheet section 10.2 for more information about threshold calculation.
-
- - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
-
- - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
- 0 - VDDA
- 1 - VDDA
- 2 - VDDA * 1.1
- 3 - VDDA * 1.2
- 4 - VDDA * 1.3
- 5 - VDDA * 1.4
- 6 - VDDA * 1.53
- 7 - VDDA * 1.53
-
- - nuvoton,sar-compare-time: SAR compare time
- 0 - 500 ns
- 1 - 1 us
- 2 - 2 us
- 3 - 4 us
-
- - nuvoton,sar-sampling-time: SAR sampling time
- 0 - 2 us
- 1 - 4 us
- 2 - 8 us
- 3 - 16 us
-
- - nuvoton,short-key-debounce: Button short key press debounce time.
- 0 - 30 ms
- 1 - 50 ms
- 2 - 100 ms
- 3 - 30 ms
-
- - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
- - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
-
- - nuvoton,crosstalk-enable: make crosstalk function enable if set.
-
- - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set.
- Otherwise, the drive keeps normal strength.
-
- - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The
- default value is 125 and range between 125 to 500 ms.
-
- - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
- clocks described in clock-names
- - clock-names: should include "mclk" for the MCLK master clock
-
-Example:
-
- headset: nau8825@1a {
- compatible = "nuvoton,nau8825";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
- nuvoton,jkdet-enable;
- nuvoton,jkdet-pull-enable;
- nuvoton,jkdet-pull-up;
- nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
- nuvoton,vref-impedance = <2>;
- nuvoton,micbias-voltage = <6>;
- // Setup 4 buttons impedance according to Android specification
- nuvoton,sar-threshold-num = <4>;
- nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
- nuvoton,sar-hysteresis = <1>;
- nuvoton,sar-voltage = <0>;
- nuvoton,sar-compare-time = <0>;
- nuvoton,sar-sampling-time = <0>;
- nuvoton,short-key-debounce = <2>;
- nuvoton,jack-insert-debounce = <7>;
- nuvoton,jack-eject-debounce = <7>;
- nuvoton,crosstalk-enable;
-
- clock-names = "mclk";
- clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>;
- };
diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml
new file mode 100644
index 000000000000..a54f194a0b49
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml
@@ -0,0 +1,239 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/nuvoton,nau8825.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NAU8825 audio CODEC
+
+maintainers:
+ - John Hsu <KCHSU0@xxxxxxxxxxx>
+
+allOf:
+ - $ref: dai-common.yaml#
+
+properties:
+ compatible:
+ enum:
+ - nuvoton,nau8825
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ nuvoton,jkdet-enable:
+ description:
+ Enable jack detection via JKDET pin.
+ type: boolean
+
+ nuvoton,jkdet-pull-enable:
+ description:
+ Enable JKDET pin pull.
+ If set - pin pull enabled, otherwise pin in high impedance state.
+ type: boolean
+
+ nuvoton,jkdet-pull-up:
+ description:
+ Pull-up JKDET pin.
+ If set then JKDET pin is pull up, otherwise pull down.
+ type: boolean
+
+ nuvoton,jkdet-polarity:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ JKDET pin polarity.
+ enum:
+ - 0 # active high
+ - 1 # active low
+ default: 1
+
+ nuvoton,vref-impedance:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ VREF Impedance selection.
+ enum:
+ - 0 # Open
+ - 1 # 25 kOhm
+ - 2 # 125 kOhm
+ - 3 # 2.5 kOhm
+ default: 2
+
+ nuvoton,micbias-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Micbias voltage level.
+ enum:
+ - 0 # VDDA
+ - 1 # VDDA
+ - 2 # VDDA * 1.1
+ - 3 # VDDA * 1.2
+ - 4 # VDDA * 1.3
+ - 5 # VDDA * 1.4
+ - 6 # VDDA * 1.53
+ - 7 # VDDA * 1.53
+ default: 6
+
+ nuvoton,sar-threshold-num:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Number of buttons supported.
+ minimum: 1
+ maximum: 4
+ default: 4
+
+ nuvoton,sar-threshold:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ Impedance threshold for each button. Array that contains up to 8 buttons
+ configuration. SAR value is calculated as
+ SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is
+ configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by
+ 'nuvoton,sar-voltage', R - button impedance.
+ Refer datasheet section 10.2 for more information about threshold
+ calculation.
+ minItems: 1
+ maxItems: 4
+ items:
+ minimum: 0
+ maximum: 255
+
+ nuvoton,sar-hysteresis:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Button impedance measurement hysteresis.
+ default: 0
+
+ nuvoton,sar-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Reference voltage for button impedance measurement.
+ enum:
+ - 0 # VDDA
+ - 1 # VDDA
+ - 2 # VDDA * 1.1
+ - 3 # VDDA * 1.2
+ - 4 # VDDA * 1.3
+ - 5 # VDDA * 1.4
+ - 6 # VDDA * 1.53
+ - 7 # VDDA * 1.53
+ default: 6
+
+ nuvoton,sar-compare-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ SAR compare time.
+ enum:
+ - 0 # 500 ns
+ - 1 # 1 us
+ - 2 # 2 us
+ - 3 # 4 us
+ default: 1
+
+ nuvoton,sar-sampling-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ SAR sampling time.
+ enum:
+ - 0 # 2 us
+ - 1 # 4 us
+ - 2 # 8 us
+ - 3 # 16 us
+ default: 1
+
+ nuvoton,short-key-debounce:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Button short key press debounce time.
+ enum:
+ - 0 # 30 ms
+ - 1 # 50 ms
+ - 2 # 100 ms
+ - 3 # 30 ms
+ default: 3
+
+ nuvoton,jack-insert-debounce:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ number from 0 to 7 that sets debounce time to 2^(n+2) ms.
+ maximum: 7
+ default: 7
+
+ nuvoton,jack-eject-debounce:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ number from 0 to 7 that sets debounce time to 2^(n+2) ms
+ maximum: 7
+ default: 0
+
+ nuvoton,crosstalk-enable:
+ description:
+ make crosstalk function enable if set.
+ type: boolean
+
+ nuvoton,adcout-drive-strong:
+ description:
+ make the drive strength of ADCOUT IO PIN strong if set.
+ Otherwise, the drive keeps normal strength.
+ type: boolean
+
+ nuvoton,adc-delay-ms:
+ description:
+ Delay (in ms) to make input path stable and avoid pop noise.
+ The default value is 125 and range between 125 to 500 ms.
+ minimum: 125
+ maximum: 500
+ default: 125
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: mclk
+
+ '#sound-dai-cells':
+ const: 0
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ codec@1a {
+ #sound-dai-cells = <0>;
+ compatible = "nuvoton,nau8825";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+ nuvoton,jkdet-enable;
+ nuvoton,jkdet-pull-enable;
+ nuvoton,jkdet-pull-up;
+ nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+ nuvoton,vref-impedance = <2>;
+ nuvoton,micbias-voltage = <6>;
+ // Setup 4 buttons impedance according to Android specification
+ nuvoton,sar-threshold-num = <4>;
+ nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+ nuvoton,sar-hysteresis = <1>;
+ nuvoton,sar-voltage = <0>;
+ nuvoton,sar-compare-time = <0>;
+ nuvoton,sar-sampling-time = <0>;
+ nuvoton,short-key-debounce = <2>;
+ nuvoton,jack-insert-debounce = <7>;
+ nuvoton,jack-eject-debounce = <7>;
+ nuvoton,crosstalk-enable;
+
+ clock-names = "mclk";
+ clocks = <&tegra_pmc 1>;
+ };
+ };
--
2.25.1
