v5 -- Remove DT property "brcm,completion-timeout-us" from
"DT bindings" commit. Although this error may be reported
as a completion timeout, its cause was traced to an
internal bus timeout which may occur even when there is
no PCIe access being processed. We set a timeout of four
seconds only if we are operating in "L1SS CLKREQ#" mode.
-- Correct CEM 2.0 reference provided by HW engineer,
s/3.2.5.2.5/3.2.5.2.2/ (Bjorn)
-- Add newline to dev_info() string (Stefan)
-- Change variable rval to unsigned (Stefan)
-- s/implementaion/implementation/ (Bjorn)
-- s/superpowersave/powersupersave/ (Bjorn)
-- Slightly modify message on "PERST#" commit.
-- Rebase to torvalds master
v4 -- New commit that asserts PERST# for 2711/RPi SOCs at PCIe RC
driver probe() time. This is done in Raspian Linux and its
absence may be the cause of a failing test case.
-- New commit that removes stale comment.
v3 -- Rewrote commit msgs and comments refering panics if L1SS
is enabled/disabled; the code snippet that unadvertises L1SS
eliminates the panic scenario. (Bjorn)
-- Add reference for "400ns of CLKREQ# assertion" blurb (Bjorn)
-- Put binding names in DT commit Subject (Bjorn)
-- Add a verb to a commit's subject line (Bjorn)
-- s/accomodat(\w+)/accommodat$1/g (Bjorn)
-- Rewrote commit msgs and comments refering panics if L1SS
is enabled/disabled; the code snippet that unadvertises L1SS
eliminates the panic scenario. (Bjorn)
v2 -- Changed binding property 'brcm,completion-timeout-msec' to
'brcm,completion-timeout-us'. (StefanW for standard suffix).
-- Warn when clamping timeout value, and include clamped
region in message. Also add min and max in YAML. (StefanW)
-- Qualify description of "brcm,completion-timeout-us" so that
it refers to PCIe transactions. (StefanW)
-- Remvove mention of Linux specifics in binding description. (StefanW)
-- s/clkreq#/CLKREQ#/g (Bjorn)
-- Refactor completion-timeout-us code to compare max and min to
value given by the property (as opposed to the computed value).
v1 -- The current driver assumes the downstream devices can
provide CLKREQ# for ASPM. These commits accomodate devices
w/ or w/o clkreq# and also handle L1SS-capable devices.
-- The Raspian Linux folks have already been using a PCIe RC
property "brcm,enable-l1ss". These commits use the same
property, in a backward-compatible manner, and the implementaion
adds more detail and also automatically identifies devices w/o
a clkreq# signal, i.e. most devices plugged into an RPi CM4
IO board.
Jim Quinlan (5):
dt-bindings: PCI: brcmstb: Add brcm,enable-l1ss property
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream
device
PCI: brcmstb: Set higher value for internal bus timeout
PCI: brcmstb: Don't assume 2711 bootloader leaves PERST# asserted
PCI: brcmstb: Remove stale comment
.../bindings/pci/brcm,stb-pcie.yaml | 9 ++
drivers/pci/controller/pcie-brcmstb.c | 91 ++++++++++++++++---
2 files changed, 89 insertions(+), 11 deletions(-)
base-commit: ac9a78681b921877518763ba0e89202254349d1b
--
2.17.1
