From: Icenowy Zheng <icenowy@xxxxxxx>
Previously SPI controllers in Allwinner SoCs has a clock divider inside.
However now the clock divider is removed and to set the transfer clock
rate it's only needed to set the SPI module clock to the target value.
Add a quirk for this kind of SPI controllers.
Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
---
drivers/spi/spi-sun6i.c | 68 +++++++++++++++++++++++------------------
1 file changed, 38 insertions(+), 30 deletions(-)
diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
index 01a01cd86db5..82523011a3a5 100644
--- a/drivers/spi/spi-sun6i.c
+++ b/drivers/spi/spi-sun6i.c
@@ -87,6 +87,7 @@
struct sun6i_spi_cfg {
unsigned long fifo_depth;
+ bool has_clk_ctl;
};
struct sun6i_spi {
@@ -260,7 +261,7 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
struct spi_transfer *tfr)
{
struct sun6i_spi *sspi = spi_master_get_devdata(master);
- unsigned int mclk_rate, div, div_cdr1, div_cdr2, timeout;
+ unsigned int div, div_cdr1, div_cdr2, timeout;
unsigned int start, end, tx_time;
unsigned int trig_level;
unsigned int tx_len = 0, rx_len = 0;
@@ -350,39 +351,44 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg);
- /* Ensure that we have a parent clock fast enough */
- mclk_rate = clk_get_rate(sspi->mclk);
- if (mclk_rate < (2 * tfr->speed_hz)) {
- clk_set_rate(sspi->mclk, 2 * tfr->speed_hz);
- mclk_rate = clk_get_rate(sspi->mclk);
- }
+ if (sspi->cfg->has_clk_ctl) {
+ unsigned int mclk_rate = clk_get_rate(sspi->mclk);
+ /* Ensure that we have a parent clock fast enough */
+ if (mclk_rate < (2 * tfr->speed_hz)) {
+ clk_set_rate(sspi->mclk, 2 * tfr->speed_hz);
+ mclk_rate = clk_get_rate(sspi->mclk);
+ }
- /*
- * Setup clock divider.
- *
- * We have two choices there. Either we can use the clock
- * divide rate 1, which is calculated thanks to this formula:
- * SPI_CLK = MOD_CLK / (2 ^ cdr)
- * Or we can use CDR2, which is calculated with the formula:
- * SPI_CLK = MOD_CLK / (2 * (cdr + 1))
- * Wether we use the former or the latter is set through the
- * DRS bit.
- *
- * First try CDR2, and if we can't reach the expected
- * frequency, fall back to CDR1.
- */
- div_cdr1 = DIV_ROUND_UP(mclk_rate, tfr->speed_hz);
- div_cdr2 = DIV_ROUND_UP(div_cdr1, 2);
- if (div_cdr2 <= (SUN6I_CLK_CTL_CDR2_MASK + 1)) {
- reg = SUN6I_CLK_CTL_CDR2(div_cdr2 - 1) | SUN6I_CLK_CTL_DRS;
- tfr->effective_speed_hz = mclk_rate / (2 * div_cdr2);
+ /*
+ * Setup clock divider.
+ *
+ * We have two choices there. Either we can use the clock
+ * divide rate 1, which is calculated thanks to this formula:
+ * SPI_CLK = MOD_CLK / (2 ^ cdr)
+ * Or we can use CDR2, which is calculated with the formula:
+ * SPI_CLK = MOD_CLK / (2 * (cdr + 1))
+ * Wether we use the former or the latter is set through the
+ * DRS bit.
+ *
+ * First try CDR2, and if we can't reach the expected
+ * frequency, fall back to CDR1.
+ */
+ div_cdr1 = DIV_ROUND_UP(mclk_rate, tfr->speed_hz);
+ div_cdr2 = DIV_ROUND_UP(div_cdr1, 2);
+ if (div_cdr2 <= (SUN6I_CLK_CTL_CDR2_MASK + 1)) {
+ reg = SUN6I_CLK_CTL_CDR2(div_cdr2 - 1) | SUN6I_CLK_CTL_DRS;
+ tfr->effective_speed_hz = mclk_rate / (2 * div_cdr2);
+ } else {
+ div = min(SUN6I_CLK_CTL_CDR1_MASK, order_base_2(div_cdr1));
+ reg = SUN6I_CLK_CTL_CDR1(div);
+ tfr->effective_speed_hz = mclk_rate / (1 << div);
+ }
+
+ sun6i_spi_write(sspi, SUN6I_CLK_CTL_REG, reg);
} else {
- div = min(SUN6I_CLK_CTL_CDR1_MASK, order_base_2(div_cdr1));
- reg = SUN6I_CLK_CTL_CDR1(div);
- tfr->effective_speed_hz = mclk_rate / (1 << div);
+ clk_set_rate(sspi->mclk, tfr->speed_hz);
}
- sun6i_spi_write(sspi, SUN6I_CLK_CTL_REG, reg);
/* Finally enable the bus - doing so before might raise SCK to HIGH */
reg = sun6i_spi_read(sspi, SUN6I_GBL_CTL_REG);
reg |= SUN6I_GBL_CTL_BUS_ENABLE;
@@ -701,10 +707,12 @@ static void sun6i_spi_remove(struct platform_device *pdev)
static const struct sun6i_spi_cfg sun6i_a31_spi_cfg = {
.fifo_depth = SUN6I_FIFO_DEPTH,
+ .has_clk_ctl = true,
};
static const struct sun6i_spi_cfg sun8i_h3_spi_cfg = {
.fifo_depth = SUN8I_FIFO_DEPTH,
+ .has_clk_ctl = true,
};
static const struct of_device_id sun6i_spi_match[] = {
--
2.39.2
