Convert the isl1208 RTC device tree binding documentation to json-schema.
Update the example to match reality.
Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
---
v2->v3:
* Updated interrupt-names property by keeping the list of names.
* Removed Interrupts from required property as it may not be wired.
* Removed isil,ev-evienb from required property.
RFC->v2:
* Updated maintainers list
* Updated description from original bindings
* removed default from isil,ev-evienb properties to match with the original
bindings.
* Added conditional check for interrupts.
---
.../devicetree/bindings/rtc/isil,isl1208.txt | 38 ---------
.../devicetree/bindings/rtc/isil,isl1208.yaml | 81 +++++++++++++++++++
2 files changed, 81 insertions(+), 38 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/rtc/isil,isl1208.txt
create mode 100644 Documentation/devicetree/bindings/rtc/isil,isl1208.yaml
diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1208.txt b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt
deleted file mode 100644
index 51f003006f04..000000000000
--- a/Documentation/devicetree/bindings/rtc/isil,isl1208.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-Intersil ISL1209/19 I2C RTC/Alarm chip with event in
-
-ISL12X9 have additional pins EVIN and #EVDET for tamper detection, while the
-ISL1208 and ISL1218 do not. They are all use the same driver with the bindings
-described here, with chip specific properties as noted.
-
-Required properties supported by the device:
- - "compatible": Should be one of the following:
- - "isil,isl1208"
- - "isil,isl1209"
- - "isil,isl1218"
- - "isil,isl1219"
- - "reg": I2C bus address of the device
-
-Optional properties:
- - "interrupt-names": list which may contains "irq" and "evdet"
- evdet applies to isl1209 and isl1219 only
- - "interrupts": list of interrupts for "irq" and "evdet"
- evdet applies to isl1209 and isl1219 only
- - "isil,ev-evienb": Enable or disable internal pull on EVIN pin
- Applies to isl1209 and isl1219 only
- Possible values are 0 and 1
- Value 0 enables internal pull-up on evin pin, 1 disables it.
- Default will leave the non-volatile configuration of the pullup
- as is.
-
-Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 and #EVDET pin
-connected to SoC gpio2 pin 24 and internal pull-up enabled in EVIN pin.
-
- isl1219: rtc@68 {
- compatible = "isil,isl1219";
- reg = <0x68>;
- interrupt-names = "irq", "evdet";
- interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>,
- <&gpio2 24 IRQ_TYPE_EDGE_FALLING>;
- isil,ev-evienb = <1>;
- };
-
diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1208.yaml b/Documentation/devicetree/bindings/rtc/isil,isl1208.yaml
new file mode 100644
index 000000000000..aee3c211d914
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/isil,isl1208.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/isil,isl1208.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intersil ISL1209/19 I2C RTC/Alarm chip with event in
+
+maintainers:
+ - Trent Piepho <tpiepho@xxxxxxxxx>
+
+description: |
+ ISL12X9 have additional pins EVIN and #EVDET for tamper detection, while the
+ ISL1208 and ISL1218 do not.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - isil,isl1208
+ - isil,isl1209
+ - isil,isl1218
+ - isil,isl1219
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 2
+
+ interrupt-names:
+ items:
+ - const: irq
+ - const: evdet
+
+ isil,ev-evienb:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 1 ]
+ description: |
+ Enable or disable internal pull on EVIN pin
+ Default will leave the non-volatile configuration of the pullup
+ as is.
+ <0> : Enables internal pull-up on evin pin
+ <1> : Disables internal pull-up on evin pin
+
+required:
+ - compatible
+ - reg
+
+allOf:
+ - $ref: rtc.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - isil,isl1209
+ - isil,isl1219
+ then:
+ properties:
+ interrupts:
+ maxItems: 2
+ else:
+ properties:
+ interrupts:
+ maxItems: 1
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtc_twi: rtc@6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+ };
--
2.25.1
