According to Renesas Electronics (formerly Dialog Semiconductor), the
standard AUTO mode of the PMIC DA9061 can lead to stability problems
depending on the hardware revision. It is recommended to set a defined
mode such as PFM or PWM permanently. So set and limit the mode for
buck 1, 2 and 3 to a fixed one.
Fixes: 611b6c891e40 ("ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board")
Signed-off-by: Christoph Niedermaier <cniedermaier@xxxxxxxxxxxxxxxxxx>
Reviewed-by: Marek Vasut <marex@xxxxxxx>
---
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx>
Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
Cc: Li Yang <leoyang.li@xxxxxxx>
Cc: Marek Vasut <marex@xxxxxxx>
Cc: Fabio Estevam <festevam@xxxxxxx>
Cc: NXP Linux Team <linux-imx@xxxxxxx>
Cc: kernel@xxxxxxxxxxxxxxxxxx
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
To: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
---
arch/arm/boot/dts/imx6ull-dhcor-som.dtsi | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi b/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
index 5882c7565f64..32a6022625d9 100644
--- a/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/regulator/dlg,da9063-regulator.h>
#include "imx6ull.dtsi"
/ {
@@ -84,16 +85,20 @@
regulators {
vdd_soc_in_1v4: buck1 {
+ regulator-allowed-modes = <DA9063_BUCK_MODE_SLEEP>; /* PFM */
regulator-always-on;
regulator-boot-on;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SLEEP>;
regulator-max-microvolt = <1400000>;
regulator-min-microvolt = <1400000>;
regulator-name = "vdd_soc_in_1v4";
};
vcc_3v3: buck2 {
+ regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
regulator-always-on;
regulator-boot-on;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <3300000>;
regulator-name = "vcc_3v3";
@@ -106,8 +111,10 @@
* the voltage is set to 1.5V.
*/
vcc_ddr_1v35: buck3 {
+ regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
regulator-always-on;
regulator-boot-on;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
regulator-max-microvolt = <1500000>;
regulator-min-microvolt = <1500000>;
regulator-name = "vcc_ddr_1v35";
--
2.11.0
