Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
* CAN1: Primary bxCAN for managing the communication between a secondary
bxCAN and the 512-byte SRAM memory.
* CAN2: Secondary bxCAN with no direct access to the SRAM memory.
This means that the two bxCAN cells share the 512-byte SRAM memory and
CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
* CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
512-byte SRAM memory.
-------------------------------------------------------------------------
| features | CAN1 | CAN2 | CAN 3 |
-------------------------------------------------------------------------
| SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte |
-------------------------------------------------------------------------
| Filters | 26 filters shared between CAN1 & CAN2 | 14 filters |
-------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@xxxxxxxxxxxxxxxxxxxx>
---
Changes in v2:
- Move after the patch "can: bxcan: add support for single peripheral configuration".
- Add node gcan3.
- Rename gcan as gcan1.
- Add property "st,can-secondary" to can2 node.
- Drop patch "dt-bindings: mfd: stm32f7: add binding definition for CAN3"
because it has been accepted.
- Add patch "ARM: dts: stm32f429: put can2 in secondary mode".
- Add patch "dt-bindings: net: can: add "st,can-secondary" property".
arch/arm/boot/dts/stm32f746.dtsi | 47 ++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index dc868e6da40e..973698bc9ef4 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -257,6 +257,23 @@ rtc: rtc@40002800 {
status = "disabled";
};
+ can3: can@40003400 {
+ compatible = "st,stm32f4-bxcan";
+ reg = <0x40003400 0x200>;
+ interrupts = <104>, <105>, <106>, <107>;
+ interrupt-names = "tx", "rx0", "rx1", "sce";
+ resets = <&rcc STM32F7_APB1_RESET(CAN3)>;
+ clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+ st,gcan = <&gcan3>;
+ status = "disabled";
+ };
+
+ gcan3: gcan@40003600 {
+ compatible = "st,stm32f4-gcan", "syscon";
+ reg = <0x40003600 0x200>;
+ clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+ };
+
usart2: serial@40004400 {
compatible = "st,stm32f7-uart";
reg = <0x40004400 0x400>;
@@ -337,6 +354,36 @@ i2c4: i2c@40006000 {
status = "disabled";
};
+ can1: can@40006400 {
+ compatible = "st,stm32f4-bxcan";
+ reg = <0x40006400 0x200>;
+ interrupts = <19>, <20>, <21>, <22>;
+ interrupt-names = "tx", "rx0", "rx1", "sce";
+ resets = <&rcc STM32F7_APB1_RESET(CAN1)>;
+ clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+ st,can-primary;
+ st,gcan = <&gcan1>;
+ status = "disabled";
+ };
+
+ gcan1: gcan@40006600 {
+ compatible = "st,stm32f4-gcan", "syscon";
+ reg = <0x40006600 0x200>;
+ clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+ };
+
+ can2: can@40006800 {
+ compatible = "st,stm32f4-bxcan";
+ reg = <0x40006800 0x200>;
+ interrupts = <63>, <64>, <65>, <66>;
+ interrupt-names = "tx", "rx0", "rx1", "sce";
+ resets = <&rcc STM32F7_APB1_RESET(CAN2)>;
+ clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN2)>;
+ st,can-secondary;
+ st,gcan = <&gcan1>;
+ status = "disabled";
+ };
+
cec: cec@40006c00 {
compatible = "st,stm32-cec";
reg = <0x40006C00 0x400>;
--
2.32.0
