From: Jyri Sarha <jsarha@xxxxxx> The OLDI-LCD1EVM add on board has Rocktech RK101II01D-CT panel with integrated touch screen. The integrated touch screen is Goodix GT928. Add DT nodes for these and connect the endpoint nodes with DSS. This patch was picked from TI's public tree based on 5.10 LTS kernel. Signed-off-by: Jyri Sarha <jsarha@xxxxxx> Signed-off-by: Nikhil Devshatwar <nikhil.nd@xxxxxx> [abhatia1@xxxxxx: Make syntax changes to support 6.1 DTSO format] Signed-off-by: Aradhya Bhatia <a-bhatia1@xxxxxx> --- arch/arm64/boot/dts/ti/Makefile | 2 + .../dts/ti/k3-am654-evm-oldi-lcd1evm.dtso | 70 +++++++++++++++++++ 2 files changed, 72 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am654-evm-oldi-lcd1evm.dtso diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index 6acd12409d59..8956b19e587a 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-m2.dtb dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am654-evm-oldi-lcd1evm.dtbo # Boards with J7200 SoC dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb @@ -45,3 +46,4 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb # Enable support for device-tree overlays DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@ +DTC_FLAGS_k3-am654-base-board += -@ diff --git a/arch/arm64/boot/dts/ti/k3-am654-evm-oldi-lcd1evm.dtso b/arch/arm64/boot/dts/ti/k3-am654-evm-oldi-lcd1evm.dtso new file mode 100644 index 000000000000..b2c790b314cf --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am654-evm-oldi-lcd1evm.dtso @@ -0,0 +1,70 @@ +// SPDX-License-Identifier: GPL-2.0 +/** + * OLDI-LCD1EVM Rocktech integrated panel and touch DT overlay for AM654-EVM. + * + * Copyright (C) 2023 Texas Instruments Incorporated - http://www.ti.com/ + */ + +/dts-v1/; +/plugin/; + +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +&{/} { + display0 { + compatible = "rocktech,rk101ii01d-ct"; + backlight = <&lcd_bl>; + enable-gpios = <&pca9555 8 GPIO_ACTIVE_HIGH>; + port { + lcd_in0: endpoint { + remote-endpoint = <&oldi_out0>; + }; + }; + }; + + lcd_bl: backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = + <0 32 64 96 128 160 192 224 255>; + default-brightness-level = <8>; + }; +}; + +&dss { + status = "okay"; +}; + +&dss_ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + oldi_out0: endpoint { + remote-endpoint = <&lcd_in0>; + }; + }; +}; + +&main_i2c1 { + #address-cells = <1>; + #size-cells = <0>; + + gt928: touchscreen@14 { + status = "okay"; + compatible = "goodix,gt928"; + reg = <0x14>; + + interrupt-parent = <&pca9554>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + touchscreen-size-x = <1280>; + touchscreen-size-y = <800>; + + reset-gpios = <&pca9555 9 GPIO_ACTIVE_HIGH>; + irq-gpios = <&pca9554 3 GPIO_ACTIVE_HIGH>; + }; +}; -- 2.39.1
