Re: [PATCH v2 9/9] dt-bindings: Add documentation for rt5033 mfd, regulator and charger

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Linus!

On 20.04.23 10:03, Linus Walleij wrote:
On Thu, Apr 20, 2023 at 9:59 AM Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:

Hi Jakob,

thanks for your patch!

The following caught my eye:

On Sun, Apr 16, 2023 at 2:50 PM Jakob Hauser <jahau@xxxxxxxxxxxxxx> wrote:

Add device tree binding documentation for rt5033 multifunction device, voltage
regulator and battery charger.

Cc: Beomho Seo <beomho.seo@xxxxxxxxxxx>
Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Signed-off-by: Jakob Hauser <jahau@xxxxxxxxxxxxxx>
---
The patch is based on linux-next (tag "next-20230413").
(...)
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/richtek,rt5033-charger.yaml
(...)
+  richtek,pre-microamp:
+    description:
+      Current of pre-charge mode. The pre-charge current levels are 350 mA to
+      650 mA programmed by I2C per 100 mA.
+    maxItems: 1
+
+  richtek,fast-microamp:
+    description:
+      Current of fast-charge mode. The fast-charge current levels are 700 mA
+      to 2000 mA programmed by I2C per 100 mA.
+    maxItems: 1
+
+  richtek,eoc-microamp:
+    description:
+      This property is end of charge current. Its level ranges from 150 mA to
+      600 mA. Between 150 mA and 300 mA in 50 mA steps, between 300 mA and 600 mA
+      in 100 mA steps.
+    maxItems: 1
+
+  richtek,pre-threshold-microvolt:
+    description:
+      Voltage of pre-charge mode. If the battery voltage is below the pre-charge
+      threshold voltage, the charger is in pre-charge mode with pre-charge current.
+      Its levels are 2.3 V to 3.8 V programmed by I2C per 0.1 V.
+    maxItems: 1
+
+  richtek,const-microvolt:
+    description:
+      Battery regulation voltage of constant voltage mode. This voltage levels from
+      3.65 V to 4.4 V by I2C per 0.025 V.
+    maxItems: 1

These are very generic currents and voltages, and their usage is well known
and generic. So they should not be prefixed "richtek,".

Use the properties already defined in
Documentation/devicetree/bindings/power/supply/battery.yaml
for these:

precharge-current-microamp
constant-charge-current-max-microamp
charge-term-current-microamp
precharge-upper-limit-microvolt
constant-charge-voltage-max-microvolt

Please double-check, I think those are the ones you need.

Perhaps it is possible to just $ref these properties directly and add
the additional restrictions on top.

On second thought, these are really weird properties to have on the
*charger* isn't it?

It is really *battery* restrictions.

A charger can charge many different batteries with different CC/CV
settings.

I think your charger should contain a phandle to a battery and the battery
node should contain these limits.

   monitored-battery:
     $ref: /schemas/types.yaml#/definitions/phandle
     description: phandle to battery node

Then you can just use the standard battery bindings for these properties
on the battery.

See for example:
Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml

There will be driver changes needed too, but this will be way cleaner.

Yours,
Linus Walleij

These are interesting hints!

I was first a bit confused by the term "battery". I associated that term with the driver "rt5033-battery". But I think that thought was wrong. The driver "rt5033-battery" is just the fuel gauge.

Hardware-wise, the mfd (incl. charger) and fuel gauge are on different I2C lines. Therefore, the different drivers access different registers.

Charger registers:
https://github.com/torvalds/linux/blob/v6.3-rc7/include/linux/mfd/rt5033-private.h#L13-L23

Fuel gauge registers:
https://github.com/torvalds/linux/blob/v6.3-rc7/include/linux/mfd/rt5033-private.h#L215-L243

The things being set or read in those registers kind of determine which things are done in which driver.

The properties we talk about here are the settings for the charger. They tell the charger how it should behave. It makes sense to process those settings within the charger driver. The fuel gauge, on the other hand, returns information like actual voltage and percentage.

The only thing that seems not placed well is the "status" property like charging/discharging/not-charging/etc. At RT5033 this information is within the charger register. Userspace layer "UPower" expects this from the "battery" device. Patch 8 of this series v2 carries that property from the charger over to the fuel gauge. Though this is a bit of a quirk. And it creates dependencies between two drivers which actually would be independent from each other.

---------------------------------

Back to the topic. When we talk about "battery" here, it seems to me that it's about the representation in the devicetree.

Currently it is:

    pmic@34 {
        compatible = "richtek,rt5033";
        ....
        charger {
            compatible = "richtek,rt5033-charger";
            richtek,pre-microamp = <450000>;
            richtek,fast-microamp = <1000000>;
            richtek,eoc-microamp = <150000>;
            richtek,pre-threshold-microvolt = <3500000>;
            richtek,const-microvolt = <4350000>;
            extcon = <&muic>;
        };
    };

According to your remarks, the properties could be "outsourced" into a
battery node. (Btw. I have double-checked the property names.)

    battery: battery {
        compatible = "simple-battery";
        precharge-current-microamp = <450000>;
        constant-charge-current-max-microamp = <1000000>;
        charge-term-current-microamp = <150000>;
        precharge-upper-limit-microvolt = <3500000>;
        constant-charge-voltage-max-microvolt = <4350000>;
    };

    pmic@34 {
        compatible = "richtek,rt5033";
        ....
        charger {
            compatible = "richtek,rt5033-charger";
            monitored-battery = <&battery>;
            extcon = <&muic>;
        };
    };

Personally I would choose the current implementation for two reasons (possibly weak ones):

1) The original author of the driver and documentation is Beomho Seo. I tried to preserve the original structure as far as possible. This is probably rather a question of editing than a technical one.

2) At least in my mind it's still the setup for the charger. It sets up a the charging behavior of a certain consumer device. And the choice of their values is limited to the hardware of the charger. Accordingly the dt-bindings would say what the charger hardware is capable to do. Therefore I'd say it's reasonable to have those values in the charger node and use vendor properties.

I agree to you that actually the physical battery is determining how these values should be set. In the end, as far as I can see, it is a representation thing in the devicetree. At least in our case here.

Not sure how to proceed here. I would stick to the current implementation. If someone strongly prefers the "battery" representation style, I'm open to switch to this.

However, I'm not sure how the dt-bindings would look like in that case. Those battery properties would not be part of the RT5033 node, thus they basically would not be part of the RT5033 documentation. Again I think it makes sense to handle those properties within the charger node as "charger settings" properties.

Kind regards,
Jakob




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux