Hi Konrad,
On Montag, 30. Jänner 2023 21:37:29 CEST Luca Weiss wrote:
> On Montag, 30. Jänner 2023 19:42:51 CET Konrad Dybcio wrote:
> > On 30.01.2023 19:36, Luca Weiss wrote:
> > > On Montag, 30. Jänner 2023 19:30:04 CET Konrad Dybcio wrote:
> > >> On 30.01.2023 19:20, luca@xxxxxxxxx wrote:
> > >>> From: Craig Tatlor <ctatlor97@xxxxxxxxx>
> > >>>
> > >>> The qfprom actually starts at 0xfc4b8000 instead of 0xfc4bc000 as
> > >>> defined previously. Adjust the tsens offsets accordingly.
> > >>>
> > >>> [luca@xxxxxxxxx: extract to standalone patch]
> > >>>
> > >>> Fixes: c59ffb519357 ("arm: dts: msm8974: Add thermal zones, tsens and
> > >>> qfprom nodes") Signed-off-by: Craig Tatlor <ctatlor97@xxxxxxxxx>
> > >>> Signed-off-by: Luca Weiss <luca@xxxxxxxxx>
> > >>> ---
> > >>
> > >> Isn't this a raw vs ecc-corrected values problem?
> > >
> > > Not quite sure what you mean.
> >
> > The QFPROM is split into two parts: one where raw values
> > are stored, and the other one where ECC-corrected copies
> > of them reside. Usually it's at offset of 0x4000. We should
> > generally be using the ECC-corrected ones, because.. well..
> > they are ECC-corrected.. You may want to check if the
> > fuse you're adding reads the same value at +0x4000.
>
> Yeah that actually seems to work...
>
> But downstream's using this +0x4000 only for tsens it seems
>
> <0xfc4bc000 0x1000> as "tsens_eeprom_physical"
>
> qcom,clock-krait-8974 is using this:
>
> <0xfc4b80b0 0x08> as "efuse"
>
> Also seems HDMI driver is using a mix for HDCP stuff
>
> drivers/video/msm/mdss/mdss_hdmi_util.h:
>
> /* QFPROM Registers for HDMI/HDCP */
> #define QFPROM_RAW_FEAT_CONFIG_ROW0_LSB (0x000000F8)
> #define QFPROM_RAW_FEAT_CONFIG_ROW0_MSB (0x000000FC)
> #define HDCP_KSV_LSB (0x000060D8)
> #define HDCP_KSV_MSB (0x000060DC)
>
> Any clue why Qualcomm used it this way in downstream? I'd rather not deviate
> too much if not for a good reason...
Any comments on the above?
Regards
Luca
>
> Regards
> Luca
>
> > Konrad
> >
> > > The original intention behind this patch is to allow to use the pvs fuse
> > > at
> > > (now) 0xb0 which was inaccessible with the former definition.
> > >
> > > pvs: pvs@b0 {
> > >
> > > reg = <0xb0 0x8>;
> > >
> > > };
> > >
> > > Regards
> > > Luca
> > >
> > >> Konrad
> > >>
> > >>> arch/arm/boot/dts/qcom-msm8974.dtsi | 12 ++++++------
> > >>> 1 file changed, 6 insertions(+), 6 deletions(-)
> > >>>
> > >>> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > >>> b/arch/arm/boot/dts/qcom-msm8974.dtsi index 8d216a3c0851..922d235c6065
> > >>> 100644
> > >>> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > >>> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > >>> @@ -1132,16 +1132,16 @@ restart@fc4ab000 {
> > >>>
> > >>> reg = <0xfc4ab000 0x4>;
> > >>>
> > >>> };
> > >>>
> > >>> - qfprom: qfprom@fc4bc000 {
> > >>> + qfprom: qfprom@fc4b8000 {
> > >>>
> > >>> compatible = "qcom,msm8974-qfprom",
> > >
> > > "qcom,qfprom";
> > >
> > >>> - reg = <0xfc4bc000 0x1000>;
> > >>> + reg = <0xfc4b8000 0x7000>;
> > >>>
> > >>> #address-cells = <1>;
> > >>> #size-cells = <1>;
> > >>>
> > >>> - tsens_calib: calib@d0 {
> > >>> - reg = <0xd0 0x18>;
> > >>> + tsens_calib: calib@40d0 {
> > >>> + reg = <0x40d0 0x18>;
> > >>>
> > >>> };
> > >>>
> > >>> - tsens_backup: backup@440 {
> > >>> - reg = <0x440 0x10>;
> > >>> + tsens_backup: backup@4440 {
> > >>> + reg = <0x4440 0x10>;
> > >>>
> > >>> };
> > >>>
> > >>> };
> > >>>
> > >>> ---
> > >>> base-commit: 6d796c50f84ca79f1722bb131799e5a5710c4700
> > >>> change-id: 20230130-msm8974-qfprom-619c0e8f26eb
> > >>>
> > >>> Best regards,
