Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts | 2 --
arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts | 1 -
arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts | 3 ---
3 files changed, 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
index 7a80e1c9f126..aa0e0e8d2a97 100644
--- a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
@@ -268,7 +268,6 @@ bluetooth_default_state: bluetooth-default-state {
function = "gpio";
drive-strength = <8>;
bias-disable;
- input-enable;
};
wlan_hostwake_default_state: wlan-hostwake-default-state {
@@ -276,7 +275,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
function = "gpio";
drive-strength = <2>;
bias-disable;
- input-enable;
};
wlan_regulator_default_state: wlan-regulator-default-state {
diff --git a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
index d64096028ab1..5593a3a60d6c 100644
--- a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
@@ -352,7 +352,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
function = "gpio";
drive-strength = <2>;
bias-disable;
- input-enable;
};
wlan_regulator_default_state: wlan-regulator-default-state {
diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
index b82381229adf..b887e5361ec3 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
@@ -307,7 +307,6 @@ bluetooth_default_state: bluetooth-default-state {
function = "gpio";
drive-strength = <2>;
bias-disable;
- input-enable;
};
touch_pins: touch-state {
@@ -317,7 +316,6 @@ irq-pins {
drive-strength = <8>;
bias-pull-down;
- input-enable;
};
reset-pins {
@@ -335,7 +333,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
function = "gpio";
drive-strength = <2>;
bias-disable;
- input-enable;
};
wlan_regulator_default_state: wlan-regulator-default-state {
--
2.34.1
