Re: [-net-next v11 6/6] net: stmmac: starfive-dmac: Add phy interface settings
From: Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx>
to: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
data: 2023/4/8
> Hi Samin,
>
> If you're respinning this series anyway, please use "net: stmmac:
> dwmac-starfive:" to match the filename.
>
Thanks, will fix.
> On Fri, 7 Apr 2023 at 13:05, Samin Guo <samin.guo@xxxxxxxxxxxxxxxx> wrote:
>>
>> dwmac supports multiple modess. When working under rmii and rgmii,
>> you need to set different phy interfaces.
>>
>> According to the dwmac document, when working in rmii, it needs to be
>> set to 0x4, and rgmii needs to be set to 0x1.
>>
>> The phy interface needs to be set in syscon, the format is as follows:
>> starfive,syscon: <&syscon, offset, shift>
>>
>> Tested-by: Tommaso Merciai <tomm.merciai@xxxxxxxxx>
>> Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
>> ---
>> .../ethernet/stmicro/stmmac/dwmac-starfive.c | 48 +++++++++++++++++++
>> 1 file changed, 48 insertions(+)
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>> index 4963d4008485..d6a1eddb51e8 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>> @@ -13,6 +13,10 @@
>>
>> #include "stmmac_platform.h"
>>
>> +#define STARFIVE_DWMAC_PHY_INFT_RGMII 0x1
>> +#define STARFIVE_DWMAC_PHY_INFT_RMII 0x4
>> +#define STARFIVE_DWMAC_PHY_INFT_FIELD 0x7U
>> +
>> struct starfive_dwmac {
>> struct device *dev;
>> struct clk *clk_tx;
>> @@ -46,6 +50,46 @@ static void starfive_dwmac_fix_mac_speed(void *priv, unsigned int speed)
>> dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate);
>> }
>>
>> +static int starfive_dwmac_set_mode(struct plat_stmmacenet_data *plat_dat)
>> +{
>> + struct starfive_dwmac *dwmac = plat_dat->bsp_priv;
>> + struct regmap *regmap;
>> + unsigned int args[2];
>> + unsigned int mode;
>> + int err;
>> +
>> + switch (plat_dat->interface) {
>> + case PHY_INTERFACE_MODE_RMII:
>> + mode = STARFIVE_DWMAC_PHY_INFT_RMII;
>> + break;
>> +
>> + case PHY_INTERFACE_MODE_RGMII:
>> + case PHY_INTERFACE_MODE_RGMII_ID:
>> + mode = STARFIVE_DWMAC_PHY_INFT_RGMII;
>> + break;
>> +
>> + default:
>> + dev_err(dwmac->dev, "unsupported interface %d\n",
>> + plat_dat->interface);
>> + return -EINVAL;
>> + }
>> +
>> + regmap = syscon_regmap_lookup_by_phandle_args(dwmac->dev->of_node,
>> + "starfive,syscon",
>> + 2, args);
>> + if (IS_ERR(regmap))
>> + return dev_err_probe(dwmac->dev, PTR_ERR(regmap), "syscon regmap failed\n");
>
> This message is a bit misleading. It's not actually that the regmap
> failed, but getting/looking up the regmap failed.
Will fix.
Best regards,
Samin
>
>> + /* args[0]:offset args[1]: shift */
>> + err = regmap_update_bits(regmap, args[0],
>> + STARFIVE_DWMAC_PHY_INFT_FIELD << args[1],
>> + mode << args[1]);
>> + if (err)
>> + return dev_err_probe(dwmac->dev, err, "error setting phy mode\n");
>> +
>> + return 0;
>> +}
>> +
>> static int starfive_dwmac_probe(struct platform_device *pdev)
>> {
>> struct plat_stmmacenet_data *plat_dat;
>> @@ -91,6 +135,10 @@ static int starfive_dwmac_probe(struct platform_device *pdev)
>> plat_dat->bsp_priv = dwmac;
>> plat_dat->dma_cfg->dche = true;
>>
>> + err = starfive_dwmac_set_mode(plat_dat);
>> + if (err)
>> + return err;
>> +
>> err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
>> if (err) {
>> stmmac_remove_config_dt(pdev, plat_dat);
>> --
>> 2.17.1
>>
>>
>> _______________________________________________
>> linux-riscv mailing list
>> linux-riscv@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/linux-riscv
