Hello Tony Dinh,
> Thecus N2350 is a NAS based on Marvell Armada 385 SoC.
>
> Board Specification:
>
> - Marvel MV88F6820 Dual Core at 1GHz
> - 1 GiB DDR4 RAM
> - 4MB Macronix mx25l3205d SPI flash
> - 512MB Hynix H27U4G8F2DTR-BC NAND flash
> - I2C
> - 2x USB 3.0
> - 1x GBE LAN port (PHY: Marvell 88E1510)
> - 2x SATA (hot swap slots)
> - 3x buttons
> - 10x LEDS
> - serial console
>
> Signed-off-by: Tony Dinh <mibodhi@xxxxxxxxx>
There were some comments on these series. If you already sent a second
version I missed it, in this case could you send it again to me ?
Else do you plan to send a v2 soon ?
Thanks,
Gregory
> ---
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/armada-385-thecus-n2350.dts | 432 ++++++++++++++++++
> 2 files changed, 433 insertions(+)
> create mode 100644 arch/arm/boot/dts/armada-385-thecus-n2350.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d08a3c450..749790e6e 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1528,6 +1528,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
> armada-385-linksys-rango.dtb \
> armada-385-linksys-shelby.dtb \
> armada-385-synology-ds116.dtb \
> + armada-385-thecus-n2350.dtb \
> armada-385-turris-omnia.dtb \
> armada-388-clearfog.dtb \
> armada-388-clearfog-base.dtb \
> diff --git a/arch/arm/boot/dts/armada-385-thecus-n2350.dts b/arch/arm/boot/dts/armada-385-thecus-n2350.dts
> new file mode 100644
> index 000000000..38114d842
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-thecus-n2350.dts
> @@ -0,0 +1,432 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Device Tree file for Thecus N2350 board
> + *
> + * Copyright (C) 2018-2023 Tony Dinh <mibodhi@xxxxxxxxx>
> + * Copyright (C) 2018 Manuel Jung <manuel.jung@xxxxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "armada-385.dtsi"
> +
> +/ {
> + model = "Thecus N2350";
> + compatible = "thecus,n2350", "marvell,armada385";
> +
> + aliases {
> + ethernet0 = ð0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x40000000>; /* 1GB */
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
> + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
> + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
> + MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
> +
> + };
> +
> + usb3_0_phy: usb3_0_phy {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <&usb3_0_power>;
> + };
> +
> + usb3_1_phy: usb3_1_phy {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <&usb3_1_power>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_power_button &pmx_copy_button &pmx_reset_button>;
> + pinctrl-names = "default";
> +
> + button@1 {
> + label = "Power Button";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> + button@2 {
> + label = "Copy Button";
> + linux,code = <KEY_COPY>;
> + gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
> + };
> +
> + button@3 {
> + label = "Reset Button";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_sata1_white_led
> + &pmx_sata1_red_led
> + &pmx_sata2_white_led
> + &pmx_sata2_red_led
> + &pmx_sys_white_led
> + &pmx_sys_red_led
> + &pmx_pwr_blue_led
> + &pmx_pwr_red_led
> + &pmx_usb_white_led
> + &pmx_usb_red_led>;
> +
> + pinctrl-names = "default";
> +
> + white_sata1 {
> + label = "n2350:white:sata1";
> + gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
> + };
> +
> + red_sata1 {
> + label = "n2350:red:sata1";
> + gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
> + };
> +
> + white-sata2 {
> + label = "n2350:white:sata2";
> + gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + red-sata2 {
> + label = "n2350:red:sata2";
> + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
> + };
> +
> + white-sys {
> + label = "n2350:white:sys";
> + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + red-sys {
> + label = "n2350:red:sys";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
> + };
> +
> + blue-pwr {
> + label = "n2350:blue:pwr";
> + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
> + };
> +
> + red-pwr {
> + label = "n2350:red:pwr";
> + gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
> + };
> +
> + white-usb {
> + label = "n2350:white:usb";
> + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
> + };
> +
> + red-usb {
> + label = "n2350:red:usb";
> + gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + usb3_0_power: regulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "USB3_0_Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
> + };
> +
> + usb3_1_power: regulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "USB3_1_Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_sata0: regulator@3 {
> + compatible = "regulator-fixed";
> + regulator-name = "pwr_en_sata0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_5v_sata0: v5-sata0 {
> + compatible = "regulator-fixed";
> + regulator-name = "v5.0-sata0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <®_sata0>;
> + };
> +
> + reg_12v_sata0: v12-sata0 {
> + compatible = "regulator-fixed";
> + regulator-name = "v12.0-sata0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + vin-supply = <®_sata0>;
> + };
> +
> + reg_sata1: regulator@4 {
> + regulator-name = "pwr_en_sata1";
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_5v_sata1: v5-sata1 {
> + compatible = "regulator-fixed";
> + regulator-name = "v5.0-sata1";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <®_sata1>;
> + };
> +
> + reg_12v_sata1: v12-sata1 {
> + compatible = "regulator-fixed";
> + regulator-name = "v12.0-sata1";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + vin-supply = <®_sata1>;
> + };
> +
> + gpio-poweroff {
> + compatible = "gpio-poweroff";
> + pinctrl-0 = <&pmx_pwr_off>;
> + pinctrl-names = "default";
> + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
> + };
> +
> +};
> +
> +&ahci0 {
> + status = "okay";
> +};
> +
> +&bm {
> + status = "okay";
> +};
> +
> +&bm_bppi {
> + status = "okay";
> +};
> +
> +ð0 {
> + status = "okay";
> + phy = <&phy0>;
> + phy-mode = "sgmii";
> + buffer-manager = <&bm>;
> + bm,pool-long = <0>;
> + bm,pool-short = <1>;
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <100000>;
> +};
> +
> +&i2c1 {
> + status = "okay";
> + clock-frequency = <100000>;
> +};
> +
> +&mdio {
> + phy0: ethernet-phy@0 {
> + reg = <1>;
> + };
> +};
> +
> +&nand_controller {
> + status = "okay";
> +
> + nand@0 {
> + status = "okay";
> + reg = <0>;
> + label = "pxa3xx_nand-0";
> + nand-rb = <0>;
> + marvell,nand-keep-config;
> + nand-on-flash-bbt;
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "rootfs";
> + reg = <0x00000000 0x20000000>;
> + };
> +
> + };
> + };
> +};
> +
> +&pciec {
> + status = "okay";
> + pcie@1,0 {
> + /* Port 0, Lane 0 */
> + status = "okay";
> + };
> + pcie@2,0 {
> + /* Port 1, Lane 0 */
> + status = "okay";
> + };
> +};
> +
> +&pinctrl {
> + pinctrl-names = "default";
> +
> + pmx_power_button: pmx-power-button {
> + marvell,pins = "mpp49";
> + marvell,function = "gpio";
> + };
> +
> + pmx_copy_button: pmx-copy-button {
> + marvell,pins = "mpp52";
> + marvell,function = "gpio";
> + };
> +
> + pmx_reset_button: pmx-reset-button {
> + marvell,pins = "mpp50";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata1_white_led: pmx-sata1-white-led {
> + marvell,pins = "mpp20";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata1_red_led: pmx-sata1-red-led {
> + marvell,pins = "mpp46";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata2_white_led: pmx-sata2-white-led {
> + marvell,pins = "mpp19";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata2_red_led: pmx-sata2-red-led {
> + marvell,pins = "mpp47";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sys_white_led: pmx-sys-white-led {
> + marvell,pins = "mpp14";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sys_red_led: pmx-sys-red-led {
> + marvell,pins = "mpp15";
> + marvell,function = "gpio";
> + };
> +
> + pmx_buzzer: pmx-buzzer {
> + marvell,pins = "mpp51";
> + marvell,function = "gpio";
> + };
> +
> + pmx_pwr_off: pmx-pwr-off {
> + marvell,pins = "mpp54";
> + marvell,function = "gpio";
> + };
> +
> + pmx_pwr_blue_led: pmx-pwr-blue-led {
> + marvell,pins = "mpp43";
> + marvell,function = "gpio";
> + };
> +
> + pmx_pwr_red_led: pmx-pwr-red-led {
> + marvell,pins = "mpp18";
> + marvell,function = "gpio";
> + };
> +
> + pmx_usb_white_led: pmx-usb-white-led {
> + marvell,pins = "mpp16";
> + marvell,function = "gpio";
> + };
> +
> + pmx_usb_red_led: pmx-usb-red-led {
> + marvell,pins = "mpp17";
> + marvell,function = "gpio";
> + };
> +};
> +
> +&sdhci {
> + broken-cd;
> + wp-inverted;
> + bus-width = <8>;
> + status = "okay";
> + no-1-8-v;
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins>;
> + status = "okay";
> +
> + /* spi: 4M Flash Macronix MX25L3205D */
> + spi-flash@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "macronix,mx25l3205d", "jedec,spi-nor";
> + reg = <0>;
> +
> + spi-max-frequency = <108000000>;
> + spi-cpha;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x00000000 0x00100000>;
> + };
> +
> + partition@100000 {
> + label = "u-boot-env";
> + reg = <0x00100000 0x00010000>;
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_1 {
> + status = "okay";
> +};
> --
> 2.30.2
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
