Hi all,
This patch series aims to enable PCI Express support for the Renesas
R-Car H1 SoC and the Marzen development board.
Unfortunately, it doesn't work completely: while an Intel E1000E network
card is detected properly:
rcar-pcie fe000000.pcie: adding to PM domain always-on
rcar-pcie fe000000.pcie: host bridge /pcie@fe000000 ranges:
rcar-pcie fe000000.pcie: IO 0x00fe100000..0x00fe1fffff -> 0x0000000000
rcar-pcie fe000000.pcie: MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000
rcar-pcie fe000000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000
rcar-pcie fe000000.pcie: MEM 0x00c0000000..0x00dfffffff -> 0x00c0000000
rcar-pcie fe000000.pcie: IB MEM 0x0040000000..0x00bfffffff -> 0x0040000000
rcar-pcie fe000000.pcie: PCIe x1: link up
rcar-pcie fe000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xfe200000-0xfe3fffff]
pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff]
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff pref]
pci 0000:00:00.0: [1912:0018] type 01 class 0x060400
pci 0000:00:00.0: enabling Extended Tags
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
PCI: bus0: Fast back to back transfers disabled
pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0001ffff]
pci 0000:01:00.0: reg 0x14: [mem 0x00000000-0x0007ffff]
pci 0000:01:00.0: reg 0x18: [io 0x0000-0x001f]
pci 0000:01:00.0: reg 0x1c: [mem 0x00000000-0x00003fff]
pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0003ffff pref]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
PCI: bus1: Fast back to back transfers disabled
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:00:00.0: BAR 8: assigned [mem 0xfe200000-0xfe2fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0xc0000000-0xc00fffff pref]
pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff]
pci 0000:01:00.0: BAR 1: assigned [mem 0xfe200000-0xfe27ffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0xc0000000-0xc003ffff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0xfe280000-0xfe29ffff]
pci 0000:01:00.0: BAR 3: assigned [mem 0xfe2a0000-0xfe2a3fff]
pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [io 0x1000-0x1fff]
pci 0000:00:00.0: bridge window [mem 0xfe200000-0xfe2fffff]
pci 0000:00:00.0: bridge window [mem 0xc0000000-0xc00fffff pref]
e1000e: Intel(R) PRO/1000 Network Driver
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
pci 0000:00:00.0: enabling device (0140 -> 0143)
e1000e 0000:01:00.0: enabling device (0140 -> 0142)
e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.
e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:c1:27:84
e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008
e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
it does not work, saying:
e1000e 0000:01:00.0 eth0: Detected Hardware Unit Hang:
I compared what happens with/without the E1000E card, and what happens on
Koelsch (R-Car M2-W), where the card does work: when the Ethernet
interface is opened, rcar_pcie_config_access() fails with a master
abort:
- PCIEERRFR.SENDURCPL = 1 (a completion with the unsupported request
status has been transmitted),
- PCICONF1.RMA = 1 (Received Master Abort).
After that, any further accesses to the E1000E's config space fail, and
"lspci -x" returns all 0xffs for the affected device.
Note that the R-Car PCIe host controller driver was originally written
for R-Car H1, H2, and M2-W, but it was never fully enabled on R-Car H1.
The only documented differences between the PCIe controllers on R-Car H1
and Gen2 seem to be the various apertures, and the PHY initialization
sequence.
Thanks for your comments and suggestions!
Geert Uytterhoeven (2):
[RFC] ARM: dts: r8a7779: Add PCIe nodes
[RFC] ARM: dts: marzen: Add PCIe support
arch/arm/boot/dts/r8a7779-marzen.dts | 8 +++++++
arch/arm/boot/dts/r8a7779.dtsi | 32 ++++++++++++++++++++++++++++
2 files changed, 40 insertions(+)
--
2.34.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
