Re: [PATCH v12 13/13] arm64: dts: ls1088ardb: Add serdes descriptions

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Mar 27, 2023 at 02:15:47PM -0400, Sean Anderson wrote:
> On 3/24/23 09:17, Ioana Ciornei wrote:
> > On Tue, Mar 21, 2023 at 04:13:12PM -0400, Sean Anderson wrote:
> >> This adds serdes support to the LS1088ARDB. I have tested the QSGMII
> >> ports as well as the two 10G ports. The SFP slot is now fully supported,
> >> instead of being modeled as a fixed-link.
> >> 
> >> Linux hangs around when the serdes is initialized if the si5341 is
> >> enabled with the in-tree driver, so I have modeled it as a two fixed
> >> clocks instead. There are a few registers in the QIXIS FPGA which
> >> control the SFP GPIOs; I have modeled them as discrete GPIO controllers
> >> for now. I never saw the AQR105 interrupt fire; not sure what was going
> >> on, but I have removed it to force polling.
> > 
> > So you didn't see the interrupt fire even without these patches?
> 
> Not sure. I went to check this, and discovered I could no longer get the
> link to come up in Linux, even on v6.0 (before the rate adaptation
> tuff). I see the LEDs blinking in U-Boot, so presumably it's some
> configuration problem. I'm going to look into this further when I have
> more time.
> 
> > I just tested this on a LS1088ARDB and it works.
> > 
> > 	root@localhost:~# cat /proc/interrupts | grep extirq
> > 	 99:          5  ls-extirq   2 Level     0x0000000008b97000:00
> > 	root@localhost:~# ip link set dev endpmac2 up
> > 	root@localhost:~# cat /proc/interrupts | grep extirq
> > 	 99:          6  ls-extirq   2 Level     0x0000000008b97000:00
> > 	root@localhost:~# ip link set dev endpmac2 down
> > 	root@localhost:~# cat /proc/interrupts | grep extirq
> > 	 99:          7  ls-extirq   2 Level     0x0000000008b97000:00
> > 
> > Please don't just remove things.
> 
> Well, polling isn't the worst thing for a single interface... I do
> remember having a problem with the interrupt. If this series works
> with interrupts enabled, I can leave it in.
> 
> Did you have a chance to look at the core (patches 7 and 8) of this
> series? Does it make sense to you? Am I missing something which would
> allow switching from 1G->10G?
> 

For a bit of context, I also attempted dynamic switching from 1G to 10G
on my own even before this patch set but I did not get a link up on the
PCS (CDR lock was there through). Pretty much the same state as you.

What I propose is to take this whole endeavor step by step.
I am also interrested in getting this feature to actually work but I
just didn't have the time to investigate in depth was is missing.
And without the dynamic switching I cannot say that I find the addition
of the SerDes PHY driver useful.

I have the Lynx 10G on my TODO list but I still have some other tasks
on the Lynx 28G for the next 2-3 weeks. Once I get those done, I will
look closer at the patches.

In the meantime, some small thigs from this patch set can be submitted
separately. For example, describing the SFP cage on the LS1088ARDB.
I still have some small questions on the DTS implementation for the gpio
controllers but I would be able to submit this myself if you do not find
the time (with your authorship of course).

Ioana



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux