Hi Peng,
On 27/3/23 20:01, Peng Fan wrote:
Subject: Re: [PATCH] arm64: dts: imx8mp: add vpu pgc nodes
On 22/8/22 14:45, Peng Fan wrote:
Add i.MX8MP PGC nodes for vpu, which are used to supply power for VPU.
Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
Signed-off-by: Shawn Guo <shawnguo@xxxxxxxxxx>
---
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 27
+++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 0b165f98a82c..34af983b0210 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -598,6 +598,33 @@ pgc_ispdwp: power-domain@18 {
reg =
<IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>;
clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>;
};
+
+ pgc_vpumix: power-domain@19 {
+ #power-domain-cells = <0>;
+ reg = <IMX8MP_POWER_DOMAIN_VPUMIX>;
+ clocks =<&clk IMX8MP_CLK_VPU_ROOT>;
+ };
+
+ pgc_vpu_g1: power-domain@20 {
+ #power-domain-cells = <0>;
+ power-domains = <&pgc_vpumix>;
+ reg = <IMX8MP_POWER_DOMAIN_VPU_G1>;
+ clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
+ };
+
+ pgc_vpu_g2: power-domain@21 {
+ #power-domain-cells = <0>;
+ power-domains = <&pgc_vpumix>;
+ reg = <IMX8MP_POWER_DOMAIN_VPU_G2>;
+ clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
+ };
+
+ pgc_vpu_vc8000e: power-domain@22 {
+ #power-domain-cells = <0>;
+ power-domains = <&pgc_vpumix>;
+ reg =
<IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
+ clocks = <&clk
IMX8MP_CLK_VPU_VC8KE_ROOT>;
+ };
};
};
};
This change causes new error messages to come out during boot, for
example:
...
imx-pgc imx-pgc-domain.8: failed to command PGC
imx-pgc imx-pgc-domain.8: failed to command PGC
imx-pgc imx-pgc-domain.8: failed to command PGC
30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 197, base_baud =
1500000) is a IMX
...
hwmon hwmon1: temp1_input not attached to any thermal zone
imx-pgc imx-pgc-domain.8: failed to command PGC
imx-pgc imx-pgc-domain.8: failed to command PGC
imx-pgc imx-pgc-domain.8: failed to command PGC
...
They don't seem to cause any problems on the hardware I am using, well, at
least not that I have found so far.
This first appeared for me in linux-6.1. But it is the same in todays linux 6.3-
rc4. Reverting this change (not completely trivial due to a couple of commits
after it that rely on it) fixes it - no more errors.
[Peng Fan]
The VPU BLK CTRL seems not enabled.
How to enable it?
I have the blk-ctrl config options enabled:
#
# i.MX SoC drivers
#
CONFIG_IMX_GPCV2_PM_DOMAINS=y
CONFIG_SOC_IMX8M=y
CONFIG_SOC_IMX9=y
CONFIG_IMX8M_BLK_CTRL=y
CONFIG_IMX9_BLK_CTRL=y
# end of i.MX SoC drivers
Running with the full arm64 defconfig and using the imx8mp-evk.dtb still
outputs these messages:
[ 18.150679] imx-pgc imx-pgc-domain.8: failed to command PGC
[ 18.159241] imx-pgc imx-pgc-domain.8: failed to command PGC
[ 18.167822] imx-pgc imx-pgc-domain.8: failed to command PGC
Or do you mean something more fundamental, like the hardware block not
being enabled by boot loader? (Something to keep in mind is that the
platform I am using has no video output, only serial console).
Regards
Greg
