Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161, update the miphy365 phy driver to access sysconfig register offsets via syscfg dt property. This is because the reg property should not be mixing address spaces like it does currently for miphy365. This change then also aligns us to how other platforms such as keystone and bcm7445 pass there syscon offsets via DT. This patch breaks DT compatibility, but this platform is considered WIP, and is only used by a few developers who are upstreaming support for it. This change has been done as a single atomic commit to ensure it is bisectable. Signed-off-by: Peter Griffin <peter.griffin@xxxxxxxxxx> --- .../devicetree/bindings/phy/phy-miphy365x.txt | 15 +++++------ arch/arm/boot/dts/stih416.dtsi | 10 ++++---- drivers/phy/phy-miphy365x.c | 29 ++++++++-------------- 3 files changed, 23 insertions(+), 31 deletions(-) diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt index 42c8808..9802d5d 100644 --- a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -6,8 +6,10 @@ for SATA and PCIe. Required properties (controller (parent) node): - compatible : Should be "st,miphy365x-phy" -- st,syscfg : Should be a phandle of the system configuration register group - which contain the SATA, PCIe mode setting bits +- st,syscfg : Phandle / integer array property. Phandle of sysconfig group + containing the miphy registers and integer array should contain + an entry for each port sub-node, specifying the control + register offset inside the sysconfig group. Required nodes : A sub-node is required for each channel the controller provides. Address range information including the usual @@ -26,7 +28,6 @@ Required properties (port (child) node): registers filled in "reg": - sata: For SATA devices - pcie: For PCIe devices - - syscfg: To specify the syscfg based config register Optional properties (port (child) node): - st,sata-gen : Generation of locally attached SATA IP. Expected values @@ -39,20 +40,20 @@ Example: miphy365x_phy: miphy365x@fe382000 { compatible = "st,miphy365x-phy"; - st,syscfg = <&syscfg_rear>; + st,syscfg = <&syscfg_rear 0x824 0x828>; #address-cells = <1>; #size-cells = <1>; ranges; phy_port0: port@fe382000 { - reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; - reg-names = "sata", "pcie", "syscfg"; + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; #phy-cells = <1>; st,sata-gen = <3>; }; phy_port1: port@fe38a000 { - reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;; + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;; reg-names = "sata", "pcie", "syscfg"; #phy-cells = <1>; st,pcie-tx-pol-inv; diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi index fad9073..6fbde39 100644 --- a/arch/arm/boot/dts/stih416.dtsi +++ b/arch/arm/boot/dts/stih416.dtsi @@ -283,21 +283,21 @@ miphy365x_phy: phy@fe382000 { compatible = "st,miphy365x-phy"; - st,syscfg = <&syscfg_rear>; + st,syscfg = <&syscfg_rear 0x824 0x828>; #address-cells = <1>; #size-cells = <1>; ranges; phy_port0: port@fe382000 { #phy-cells = <1>; - reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; - reg-names = "sata", "pcie", "syscfg"; + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; }; phy_port1: port@fe38a000 { #phy-cells = <1>; - reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>; - reg-names = "sata", "pcie", "syscfg"; + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>; + reg-names = "sata", "pcie"; }; }; diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c index 801afaf..7308afe 100644 --- a/drivers/phy/phy-miphy365x.c +++ b/drivers/phy/phy-miphy365x.c @@ -141,7 +141,7 @@ struct miphy365x_phy { bool pcie_tx_pol_inv; bool sata_tx_pol_inv; u32 sata_gen; - u64 ctrlreg; + u32 ctrlreg; u8 type; }; @@ -179,7 +179,7 @@ static int miphy365x_set_path(struct miphy365x_phy *miphy_phy, bool sata = (miphy_phy->type == MIPHY_TYPE_SATA); return regmap_update_bits(miphy_dev->regmap, - (unsigned int)miphy_phy->ctrlreg, + miphy_phy->ctrlreg, SYSCFG_SELECT_SATA_MASK, sata << SYSCFG_SELECT_SATA_POS); } @@ -445,7 +445,6 @@ int miphy365x_get_addr(struct device *dev, struct miphy365x_phy *miphy_phy, { struct device_node *phynode = miphy_phy->phy->dev.of_node; const char *name; - const __be32 *taddr; int type = miphy_phy->type; int ret; @@ -455,22 +454,6 @@ int miphy365x_get_addr(struct device *dev, struct miphy365x_phy *miphy_phy, return ret; } - if (!strncmp(name, "syscfg", 6)) { - taddr = of_get_address(phynode, index, NULL, NULL); - if (!taddr) { - dev_err(dev, "failed to fetch syscfg address\n"); - return -EINVAL; - } - - miphy_phy->ctrlreg = of_translate_address(phynode, taddr); - if (miphy_phy->ctrlreg == OF_BAD_ADDR) { - dev_err(dev, "failed to translate syscfg address\n"); - return -EINVAL; - } - - return 0; - } - if (!((!strncmp(name, "sata", 4) && type == MIPHY_TYPE_SATA) || (!strncmp(name, "pcie", 4) && type == MIPHY_TYPE_PCIE))) return 0; @@ -606,7 +589,15 @@ static int miphy365x_probe(struct platform_device *pdev) return ret; phy_set_drvdata(phy, miphy_dev->phys[port]); + port++; + /*sysconfig offsets are not indexed from zero */ + ret = of_property_read_u32_index(np, "st,syscfg", port, + &miphy_phy->ctrlreg); + if (ret) { + dev_err(&pdev->dev, "No sysconfig offset found\n"); + return ret; + } } provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
