On 3/21/23 15:16, Mehdi Djait wrote:
Hi Matti,
On Sun, Mar 19, 2023 at 09:43:19AM +0200, Matti Vaittinen wrote:
Hi Mehdi,
Things have been piling up for me during last two weeks... I will do proper
review during next week.
On 3/17/23 01:48, Mehdi Djait wrote:
KX132 accelerometer is a sensor which:
- supports G-ranges of (+/-) 2, 4, 8, and 16G
- can be connected to I2C or SPI
- has internal HW FIFO buffer
- supports various ODRs (output data rates)
The KX132 accelerometer is very similair to the KX022A.
One key difference is number of bits to report the number of data bytes that
have been stored in the sample buffer: 8 bits for KX022A vs 10 bits for KX132.
The KX022A has 16bits of data in HiRes mode. This is the default for kx022a
driver.
I am talking here about "Buffer Sample Level number of bits":
Ah. My bad. I misunderstood. Mentioning the number of bits made me to
instantly think of the format of measured data not the size of the FIFO
and how many bits are needed to represent the full FIFO.
kx022a uses
8 bits: just BUF_STATUS_1 to report the status of the buffer. kx132 uses
BUF_STATUS_1 and the Bit0, Bit1 of BUF_STATUS_2.
That's the reason for adding the kx022a_get_fifo_bytes function.
A complete list of differences is listed in [1]
[1] https://kionixfs.azureedge.net/en/document/AN112-Transitioning-to-KX132-1211-Accelerometer.pdf1
This document is somewhat misleading. It does not contain KX022A but the
older KX022. Kionix has the somewhat confusing habit of having very similar
names for models with - occasionally significant - differences. (My own
opinion).
Yes, I am aware that it does not contain KX022A, but from my
understanding of your code, the document can be used to highlight the
difference I mentioned
I don't remember all the differences between the KX022 and KX022A - but
I believe at least the supported G-ranges were different. I think there
probably were also some other things.
Finally, AFAIK the key "thing" in KX132 is the "ADP" (Advanced Data Path)
feature which allows filtering the data "in sensor". Unfortunately, I am not
really familiar with this feature. Do you think this is something that might
get configured only once at start-up depending on the purpose of the board?
If yes, this might be something that will end-up having properties in
device-tree. If yes, then it might be a good idea to have own binding doc
for KX132. Currently it seems Ok to have them in the same binding doc
though.
Correct me if I am wrong: the Devicetree is a description of the
hardware
Yes.
and the transitioning document states:
"From a hardware perspective, all these sensors
have an identical pad/pin layouts and identical pin functionality"
Sometimes (fixed) hardware _configuration_ can be visible in
device-tree. Eg, device-tree can be used to tell: "On this board this
configurable piece of hardware shall look like this". My understanding
of ADP is very limited, but I thought it may be used to adjust the
hardware by for example adding some filters.
As I said, I however don't know if the ADP will be used with 'static
configurations' which could be seen as hardware properties. Hence I
asked if you had insight to this.
I was thinking about adding an advanced_data_path boolean to the chip_info
struct and providing different driver callbacks depending on the value.
I can't really comment on this much as I lack of knowledge. I have
understood the ADP can be configured to do very different type of
filtering(?) I wonder how the boolean flag suits these needs but I guess
we can go into those details when ADP support is being implemented.
Right now I am happy if you say you have analyzed the ADP to the point
you don't expect many kx132 specific dt-bindings to be needed. And. even
if this analysis was wrong, we can later separate the kx132 bindings to
own doc if that is needed. So, I am happy with the bindings being in
same file now.
Something like in the bmc150-accel-core: iio_info for bmc150_accel_info
and iio_info for bmc150_accel_info_fifo
I will see those later, thanks.
Yours
-- Matti
--
Matti Vaittinen
Linux kernel developer at ROHM Semiconductors
Oulu Finland
~~ When things go utterly wrong vim users can always type :help! ~~
