Re: [PATCH v2] leds: lp8860: Introduce TI lp8860 4 channel LED driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, Nov 18, 2014 at 6:43 AM, Dan Murphy <dmurphy@xxxxxx> wrote:
> Introduce the Texas Instruments lp8860
> 4 channel LED driver.
>
> This driver configures the device in display cluster mode
> as this seems to be the most used configuration at the
> time of the driver configuration.
>
> For more product information please see the link below:
> http://www.ti.com/product/lp8860-q1
>
> Signed-off-by: Dan Murphy <dmurphy@xxxxxx>
> ---
>
> v2 - Fixed commit message spelling, changed flush_work to
> cancel_work, did not move INIT_WORK as led class is not registered
> until the end of probe - https://patchwork.kernel.org/patch/5296361
>

Thanks for updating, I applied this patch into my tree.
-Bryan

>  .../devicetree/bindings/leds/leds-lp8860.txt       |  29 ++
>  drivers/leds/Kconfig                               |  10 +
>  drivers/leds/Makefile                              |   1 +
>  drivers/leds/leds-lp8860.c                         | 491 +++++++++++++++++++++
>  4 files changed, 531 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-lp8860.txt
>  create mode 100644 drivers/leds/leds-lp8860.c
>
> diff --git a/Documentation/devicetree/bindings/leds/leds-lp8860.txt b/Documentation/devicetree/bindings/leds/leds-lp8860.txt
> new file mode 100644
> index 0000000..aad38dd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-lp8860.txt
> @@ -0,0 +1,29 @@
> +* Texas Instruments - lp8860 4-Channel LED Driver
> +
> +The LP8860-Q1 is an high-efficiency LED
> +driver with boost controller. It has 4 high-precision
> +current sinks that can be controlled by a PWM input
> +signal, a SPI/I2C master, or both.
> +
> +Required properties:
> +       - compatible:
> +               "ti,lp8860"
> +       - reg -  I2C slave address
> +       - label - Used for naming LEDs
> +
> +Optional properties:
> +       - enable-gpio - gpio pin to enable/disable the device.
> +       - supply - "vled" - LED supply
> +
> +Example:
> +
> +leds: leds@6 {
> +       compatible = "ti,lp8860";
> +       reg = <0x2d>;
> +       label = "display_cluster";
> +       enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> +       vled-supply = <&vbatt>;
> +}
> +
> +For more product information please see the link below:
> +http://www.ti.com/product/lp8860-q1
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index a210338..b0dce59 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -250,6 +250,16 @@ config LEDS_LP8788
>         help
>           This option enables support for the Keyboard LEDs on the LP8788 PMIC.
>
> +config LEDS_LP8860
> +       tristate "LED support for the TI LP8860 4 channel LED driver"
> +       depends on LEDS_CLASS && REGMAP_I2C
> +       help
> +         If you say yes here you get support for the TI LP8860 4 channel
> +         LED driver.
> +         This option enables support for the display cluster LEDs
> +         on the LP8860 4 channel LED driver using the I2C communication
> +         bus.
> +
>  config LEDS_CLEVO_MAIL
>         tristate "Mail LED on Clevo notebook"
>         depends on LEDS_CLASS
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index a2b1647..1c65a19 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_LEDS_LP5523)             += leds-lp5523.o
>  obj-$(CONFIG_LEDS_LP5562)              += leds-lp5562.o
>  obj-$(CONFIG_LEDS_LP8501)              += leds-lp8501.o
>  obj-$(CONFIG_LEDS_LP8788)              += leds-lp8788.o
> +obj-$(CONFIG_LEDS_LP8860)              += leds-lp8860.o
>  obj-$(CONFIG_LEDS_TCA6507)             += leds-tca6507.o
>  obj-$(CONFIG_LEDS_CLEVO_MAIL)          += leds-clevo-mail.o
>  obj-$(CONFIG_LEDS_IPAQ_MICRO)          += leds-ipaq-micro.o
> diff --git a/drivers/leds/leds-lp8860.c b/drivers/leds/leds-lp8860.c
> new file mode 100644
> index 0000000..54e4eec
> --- /dev/null
> +++ b/drivers/leds/leds-lp8860.c
> @@ -0,0 +1,491 @@
> +/*
> + * TI LP8860 4-Channel LED Driver
> + *
> + * Copyright (C) 2014 Texas Instruments
> + *
> + * Author: Dan Murphy <dmurphy@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + */
> +
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/leds.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/of_gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/slab.h>
> +
> +#define LP8860_DISP_CL1_BRT_MSB                0x00
> +#define LP8860_DISP_CL1_BRT_LSB                0x01
> +#define LP8860_DISP_CL1_CURR_MSB       0x02
> +#define LP8860_DISP_CL1_CURR_LSB       0x03
> +#define LP8860_CL2_BRT_MSB             0x04
> +#define LP8860_CL2_BRT_LSB             0x05
> +#define LP8860_CL2_CURRENT             0x06
> +#define LP8860_CL3_BRT_MSB             0x07
> +#define LP8860_CL3_BRT_LSB             0x08
> +#define LP8860_CL3_CURRENT             0x09
> +#define LP8860_CL4_BRT_MSB             0x0a
> +#define LP8860_CL4_BRT_LSB             0x0b
> +#define LP8860_CL4_CURRENT             0x0c
> +#define LP8860_CONFIG                  0x0d
> +#define LP8860_STATUS                  0x0e
> +#define LP8860_FAULT                   0x0f
> +#define LP8860_LED_FAULT               0x10
> +#define LP8860_FAULT_CLEAR             0x11
> +#define LP8860_ID                      0x12
> +#define LP8860_TEMP_MSB                        0x13
> +#define LP8860_TEMP_LSB                        0x14
> +#define LP8860_DISP_LED_CURR_MSB       0x15
> +#define LP8860_DISP_LED_CURR_LSB       0x16
> +#define LP8860_DISP_LED_PWM_MSB                0x17
> +#define LP8860_DISP_LED_PWM_LSB                0x18
> +#define LP8860_EEPROM_CNTRL            0x19
> +#define LP8860_EEPROM_UNLOCK           0x1a
> +
> +#define LP8860_EEPROM_REG_0            0x60
> +#define LP8860_EEPROM_REG_1            0x61
> +#define LP8860_EEPROM_REG_2            0x62
> +#define LP8860_EEPROM_REG_3            0x63
> +#define LP8860_EEPROM_REG_4            0x64
> +#define LP8860_EEPROM_REG_5            0x65
> +#define LP8860_EEPROM_REG_6            0x66
> +#define LP8860_EEPROM_REG_7            0x67
> +#define LP8860_EEPROM_REG_8            0x68
> +#define LP8860_EEPROM_REG_9            0x69
> +#define LP8860_EEPROM_REG_10           0x6a
> +#define LP8860_EEPROM_REG_11           0x6b
> +#define LP8860_EEPROM_REG_12           0x6c
> +#define LP8860_EEPROM_REG_13           0x6d
> +#define LP8860_EEPROM_REG_14           0x6e
> +#define LP8860_EEPROM_REG_15           0x6f
> +#define LP8860_EEPROM_REG_16           0x70
> +#define LP8860_EEPROM_REG_17           0x71
> +#define LP8860_EEPROM_REG_18           0x72
> +#define LP8860_EEPROM_REG_19           0x73
> +#define LP8860_EEPROM_REG_20           0x74
> +#define LP8860_EEPROM_REG_21           0x75
> +#define LP8860_EEPROM_REG_22           0x76
> +#define LP8860_EEPROM_REG_23           0x77
> +#define LP8860_EEPROM_REG_24           0x78
> +
> +#define LP8860_LOCK_EEPROM             0x00
> +#define LP8860_UNLOCK_EEPROM           0x01
> +#define LP8860_PROGRAM_EEPROM          0x02
> +#define LP8860_EEPROM_CODE_1           0x08
> +#define LP8860_EEPROM_CODE_2           0xba
> +#define LP8860_EEPROM_CODE_3           0xef
> +
> +#define LP8860_CLEAR_FAULTS            0x01
> +
> +#define LP8860_DISP_LED_NAME           "display_cluster"
> +
> +/**
> + * struct lp8860_led -
> + * @lock - Lock for reading/writing the device
> + * @work - Work item used to off load the brightness register writes
> + * @client - Pointer to the I2C client
> + * @led_dev - led class device pointer
> + * @regmap - Devices register map
> + * @eeprom_regmap - EEPROM register map
> + * @enable_gpio - VDDIO/EN gpio to enable communication interface
> + * @regulator - LED supply regulator pointer
> + * @brightness - Current brightness value requested
> + * @label - LED label
> +**/
> +struct lp8860_led {
> +       struct mutex lock;
> +       struct work_struct work;
> +       struct i2c_client *client;
> +       struct led_classdev led_dev;
> +       struct regmap *regmap;
> +       struct regmap *eeprom_regmap;
> +       struct gpio_desc *enable_gpio;
> +       struct regulator *regulator;
> +       enum led_brightness brightness;
> +       const char *label;
> +};
> +
> +struct lp8860_eeprom_reg {
> +       uint8_t reg;
> +       uint8_t value;
> +};
> +
> +struct lp8860_eeprom_reg lp8860_eeprom_disp_regs[] = {
> +       { LP8860_EEPROM_REG_0, 0xed },
> +       { LP8860_EEPROM_REG_1, 0xdf },
> +       { LP8860_EEPROM_REG_2, 0xdc },
> +       { LP8860_EEPROM_REG_3, 0xf0 },
> +       { LP8860_EEPROM_REG_4, 0xdf },
> +       { LP8860_EEPROM_REG_5, 0xe5 },
> +       { LP8860_EEPROM_REG_6, 0xf2 },
> +       { LP8860_EEPROM_REG_7, 0x77 },
> +       { LP8860_EEPROM_REG_8, 0x77 },
> +       { LP8860_EEPROM_REG_9, 0x71 },
> +       { LP8860_EEPROM_REG_10, 0x3f },
> +       { LP8860_EEPROM_REG_11, 0xb7 },
> +       { LP8860_EEPROM_REG_12, 0x17 },
> +       { LP8860_EEPROM_REG_13, 0xef },
> +       { LP8860_EEPROM_REG_14, 0xb0 },
> +       { LP8860_EEPROM_REG_15, 0x87 },
> +       { LP8860_EEPROM_REG_16, 0xce },
> +       { LP8860_EEPROM_REG_17, 0x72 },
> +       { LP8860_EEPROM_REG_18, 0xe5 },
> +       { LP8860_EEPROM_REG_19, 0xdf },
> +       { LP8860_EEPROM_REG_20, 0x35 },
> +       { LP8860_EEPROM_REG_21, 0x06 },
> +       { LP8860_EEPROM_REG_22, 0xdc },
> +       { LP8860_EEPROM_REG_23, 0x88 },
> +       { LP8860_EEPROM_REG_24, 0x3E },
> +};
> +
> +static int lp8860_unlock_eeprom(struct lp8860_led *led, int lock)
> +{
> +       int ret;
> +
> +       mutex_lock(&led->lock);
> +
> +       if (lock == LP8860_UNLOCK_EEPROM) {
> +               ret = regmap_write(led->regmap,
> +                       LP8860_EEPROM_UNLOCK,
> +                       LP8860_EEPROM_CODE_1);
> +               if (ret) {
> +                       dev_err(&led->client->dev, "EEPROM Unlock failed\n");
> +                       goto out;
> +               }
> +
> +               ret = regmap_write(led->regmap,
> +                       LP8860_EEPROM_UNLOCK,
> +                       LP8860_EEPROM_CODE_2);
> +               if (ret) {
> +                       dev_err(&led->client->dev, "EEPROM Unlock failed\n");
> +                       goto out;
> +               }
> +               ret = regmap_write(led->regmap,
> +                       LP8860_EEPROM_UNLOCK,
> +                       LP8860_EEPROM_CODE_3);
> +               if (ret) {
> +                       dev_err(&led->client->dev, "EEPROM Unlock failed\n");
> +                       goto out;
> +               }
> +       } else {
> +               ret = regmap_write(led->regmap,
> +                       LP8860_EEPROM_UNLOCK,
> +                       LP8860_LOCK_EEPROM);
> +       }
> +
> +out:
> +       mutex_unlock(&led->lock);
> +       return ret;
> +}
> +
> +static int lp8860_fault_check(struct lp8860_led *led)
> +{
> +       int ret, fault;
> +       unsigned int read_buf;
> +
> +       ret = regmap_read(led->regmap, LP8860_LED_FAULT, &read_buf);
> +       if (ret)
> +               goto out;
> +
> +       fault = read_buf;
> +
> +       ret = regmap_read(led->regmap, LP8860_FAULT, &read_buf);
> +       if (ret)
> +               goto out;
> +
> +       fault |= read_buf;
> +
> +       /* Attempt to clear any faults */
> +       if (fault)
> +               ret = regmap_write(led->regmap, LP8860_FAULT_CLEAR,
> +                       LP8860_CLEAR_FAULTS);
> +out:
> +       return ret;
> +}
> +
> +static void lp8860_led_brightness_work(struct work_struct *work)
> +{
> +       struct lp8860_led *led = container_of(work, struct lp8860_led, work);
> +       int ret;
> +       int disp_brightness = led->brightness * 255;
> +
> +       mutex_lock(&led->lock);
> +
> +       ret = lp8860_fault_check(led);
> +       if (ret) {
> +               dev_err(&led->client->dev, "Cannot read/clear faults\n");
> +               goto out;
> +       }
> +
> +       ret = regmap_write(led->regmap, LP8860_DISP_CL1_BRT_MSB,
> +                       (disp_brightness & 0xff00) >> 8);
> +       if (ret) {
> +               dev_err(&led->client->dev, "Cannot write CL1 MSB\n");
> +               goto out;
> +       }
> +
> +       ret = regmap_write(led->regmap, LP8860_DISP_CL1_BRT_LSB,
> +                       disp_brightness & 0xff);
> +       if (ret) {
> +               dev_err(&led->client->dev, "Cannot write CL1 LSB\n");
> +               goto out;
> +       }
> +out:
> +       mutex_unlock(&led->lock);
> +}
> +
> +static void lp8860_brightness_set(struct led_classdev *led_cdev,
> +                               enum led_brightness brt_val)
> +{
> +       struct lp8860_led *led =
> +                       container_of(led_cdev, struct lp8860_led, led_dev);
> +
> +       led->brightness = brt_val;
> +       schedule_work(&led->work);
> +}
> +
> +static int lp8860_init(struct lp8860_led *led)
> +{
> +       unsigned int read_buf;
> +       int ret, i, reg_count;
> +
> +       if (led->enable_gpio)
> +               gpiod_direction_output(led->enable_gpio, 1);
> +
> +       ret = lp8860_fault_check(led);
> +       if (ret)
> +               goto out;
> +
> +       ret = regmap_read(led->regmap, LP8860_STATUS, &read_buf);
> +       if (ret)
> +               goto out;
> +
> +       ret = lp8860_unlock_eeprom(led, LP8860_UNLOCK_EEPROM);
> +       if (ret) {
> +               dev_err(&led->client->dev, "Failed unlocking EEPROM\n");
> +               goto out;
> +       }
> +
> +       reg_count = ARRAY_SIZE(lp8860_eeprom_disp_regs) / sizeof(lp8860_eeprom_disp_regs[0]);
> +       for (i = 0; i < reg_count; i++) {
> +               ret = regmap_write(led->eeprom_regmap,
> +                               lp8860_eeprom_disp_regs[i].reg,
> +                               lp8860_eeprom_disp_regs[i].value);
> +               if (ret) {
> +                       dev_err(&led->client->dev, "Failed writing EEPROM\n");
> +                       goto out;
> +               }
> +       }
> +
> +       ret = lp8860_unlock_eeprom(led, LP8860_LOCK_EEPROM);
> +       if (ret)
> +               goto out;
> +
> +       ret = regmap_write(led->regmap,
> +                       LP8860_EEPROM_CNTRL,
> +                       LP8860_PROGRAM_EEPROM);
> +       if (ret)
> +               dev_err(&led->client->dev, "Failed programming EEPROM\n");
> +out:
> +       if (ret)
> +               if (led->enable_gpio)
> +                       gpiod_direction_output(led->enable_gpio, 0);
> +       return ret;
> +}
> +
> +static struct reg_default lp8860_reg_defs[] = {
> +       { LP8860_DISP_CL1_BRT_MSB, 0x00},
> +       { LP8860_DISP_CL1_BRT_LSB, 0x00},
> +       { LP8860_DISP_CL1_CURR_MSB, 0x00},
> +       { LP8860_DISP_CL1_CURR_LSB, 0x00},
> +       { LP8860_CL2_BRT_MSB, 0x00},
> +       { LP8860_CL2_BRT_LSB, 0x00},
> +       { LP8860_CL2_CURRENT, 0x00},
> +       { LP8860_CL3_BRT_MSB, 0x00},
> +       { LP8860_CL3_BRT_LSB, 0x00},
> +       { LP8860_CL3_CURRENT, 0x00},
> +       { LP8860_CL4_BRT_MSB, 0x00},
> +       { LP8860_CL4_BRT_LSB, 0x00},
> +       { LP8860_CL4_CURRENT, 0x00},
> +       { LP8860_CONFIG, 0x00},
> +       { LP8860_FAULT_CLEAR, 0x00},
> +       { LP8860_EEPROM_CNTRL, 0x80},
> +       { LP8860_EEPROM_UNLOCK, 0x00},
> +};
> +
> +static const struct regmap_config lp8860_regmap_config = {
> +       .reg_bits = 8,
> +       .val_bits = 8,
> +
> +       .max_register = LP8860_EEPROM_UNLOCK,
> +       .reg_defaults = lp8860_reg_defs,
> +       .num_reg_defaults = ARRAY_SIZE(lp8860_reg_defs),
> +       .cache_type = REGCACHE_NONE,
> +};
> +
> +static struct reg_default lp8860_eeprom_defs[] = {
> +       { LP8860_EEPROM_REG_0, 0x00 },
> +       { LP8860_EEPROM_REG_1, 0x00 },
> +       { LP8860_EEPROM_REG_2, 0x00 },
> +       { LP8860_EEPROM_REG_3, 0x00 },
> +       { LP8860_EEPROM_REG_4, 0x00 },
> +       { LP8860_EEPROM_REG_5, 0x00 },
> +       { LP8860_EEPROM_REG_6, 0x00 },
> +       { LP8860_EEPROM_REG_7, 0x00 },
> +       { LP8860_EEPROM_REG_8, 0x00 },
> +       { LP8860_EEPROM_REG_9, 0x00 },
> +       { LP8860_EEPROM_REG_10, 0x00 },
> +       { LP8860_EEPROM_REG_11, 0x00 },
> +       { LP8860_EEPROM_REG_12, 0x00 },
> +       { LP8860_EEPROM_REG_13, 0x00 },
> +       { LP8860_EEPROM_REG_14, 0x00 },
> +       { LP8860_EEPROM_REG_15, 0x00 },
> +       { LP8860_EEPROM_REG_16, 0x00 },
> +       { LP8860_EEPROM_REG_17, 0x00 },
> +       { LP8860_EEPROM_REG_18, 0x00 },
> +       { LP8860_EEPROM_REG_19, 0x00 },
> +       { LP8860_EEPROM_REG_20, 0x00 },
> +       { LP8860_EEPROM_REG_21, 0x00 },
> +       { LP8860_EEPROM_REG_22, 0x00 },
> +       { LP8860_EEPROM_REG_23, 0x00 },
> +       { LP8860_EEPROM_REG_24, 0x00 },
> +};
> +
> +static const struct regmap_config lp8860_eeprom_regmap_config = {
> +       .reg_bits = 8,
> +       .val_bits = 8,
> +
> +       .max_register = LP8860_EEPROM_REG_24,
> +       .reg_defaults = lp8860_eeprom_defs,
> +       .num_reg_defaults = ARRAY_SIZE(lp8860_eeprom_defs),
> +       .cache_type = REGCACHE_NONE,
> +};
> +
> +static int lp8860_probe(struct i2c_client *client,
> +                       const struct i2c_device_id *id)
> +{
> +       int ret;
> +       struct lp8860_led *led;
> +       struct device_node *np = client->dev.of_node;
> +
> +       led = devm_kzalloc(&client->dev, sizeof(*led), GFP_KERNEL);
> +       if (!led)
> +               return -ENOMEM;
> +
> +       led->label = LP8860_DISP_LED_NAME;
> +
> +       if (client->dev.of_node) {
> +               ret = of_property_read_string(np, "label", &led->label);
> +               if (ret) {
> +                       dev_err(&client->dev, "Missing label in dt\n");
> +                       return -EINVAL;
> +               }
> +       }
> +
> +       led->enable_gpio = devm_gpiod_get(&client->dev, "enable");
> +       if (IS_ERR(led->enable_gpio))
> +               led->enable_gpio = NULL;
> +       else
> +               gpiod_direction_output(led->enable_gpio, 0);
> +
> +       led->regulator = devm_regulator_get(&client->dev, "vled");
> +       if (IS_ERR(led->regulator))
> +               led->regulator = NULL;
> +
> +       led->client = client;
> +       led->led_dev.name = led->label;
> +       led->led_dev.max_brightness = LED_FULL;
> +       led->led_dev.brightness_set = lp8860_brightness_set;
> +
> +       mutex_init(&led->lock);
> +       INIT_WORK(&led->work, lp8860_led_brightness_work);
> +
> +       i2c_set_clientdata(client, led);
> +
> +       led->regmap = devm_regmap_init_i2c(client, &lp8860_regmap_config);
> +       if (IS_ERR(led->regmap)) {
> +               ret = PTR_ERR(led->regmap);
> +               dev_err(&client->dev, "Failed to allocate register map: %d\n",
> +                       ret);
> +               return ret;
> +       }
> +
> +       led->eeprom_regmap = devm_regmap_init_i2c(client, &lp8860_eeprom_regmap_config);
> +       if (IS_ERR(led->eeprom_regmap)) {
> +               ret = PTR_ERR(led->eeprom_regmap);
> +               dev_err(&client->dev, "Failed to allocate register map: %d\n",
> +                       ret);
> +               return ret;
> +       }
> +
> +       ret = lp8860_init(led);
> +       if (ret)
> +               return ret;
> +
> +       ret = led_classdev_register(&client->dev, &led->led_dev);
> +       if (ret) {
> +               dev_err(&client->dev, "led register err: %d\n", ret);
> +               return ret;
> +       }
> +
> +       return 0;
> +}
> +
> +static int lp8860_remove(struct i2c_client *client)
> +{
> +       struct lp8860_led *led = i2c_get_clientdata(client);
> +       int ret;
> +
> +       led_classdev_unregister(&led->led_dev);
> +       cancel_work_sync(&led->work);
> +
> +       if (led->enable_gpio)
> +               gpiod_direction_output(led->enable_gpio, 0);
> +
> +       if (led->regulator) {
> +               ret = regulator_disable(led->regulator);
> +               if (ret)
> +                       dev_err(&led->client->dev,
> +                               "Failed to disable regulator\n");
> +       }
> +
> +       return 0;
> +}
> +
> +static const struct i2c_device_id lp8860_id[] = {
> +       { "lp8860", 0 },
> +       { }
> +};
> +MODULE_DEVICE_TABLE(i2c, lp8860_id);
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id of_lp8860_leds_match[] = {
> +       { .compatible = "ti,lp8860", },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, of_lp8860_leds_match);
> +#endif
> +
> +static struct i2c_driver lp8860_driver = {
> +       .driver = {
> +               .name   = "lp8860",
> +               .of_match_table = of_match_ptr(of_lp8860_leds_match),
> +       },
> +       .probe          = lp8860_probe,
> +       .remove         = lp8860_remove,
> +       .id_table       = lp8860_id,
> +};
> +module_i2c_driver(lp8860_driver);
> +
> +MODULE_DESCRIPTION("Texas Instruments LP8860 LED drvier");
> +MODULE_AUTHOR("Dan Murphy <dmurphy@xxxxxx>");
> +MODULE_LICENSE("GPL");
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux