This patch series adds basic clock, reset & DT support for StarFive JH7110 SoC. You can simply review or test the patches at the link [1]. [1]: https://github.com/hal-feng/linux/commits/visionfive2-minimal Changes since v5: - Rebased on v6.3-rc3. Patch 1: - Set obj-y for starfive/ in drivers/clk/Makefile. Patch 2: - Sorted the StarFive entries alphabetically in MAINTAINERS. Patch 3: - Fixed the build error which caused by renaming the header without changing the users of the header. Patch 4: - Fixed the errors reported by checkpatch.pl. Patch 6: - Set obj-y for starfive/ in drivers/reset/Makefile. Patch 13: - Set the timer clock flags as 0. v5: https://lore.kernel.org/all/20230311090733.56918-1-hal.feng@xxxxxxxxxxxxxxxx/ Changes since v4: - Rebased on v6.3-rc1. - Added two patches to replace SOC_STARFIVE with ARCH_STARFIVE. - Added Tested-by tag for Tommaso. Patch 9: - Set GMAC1 related clocks as optional inputs. - Dropped PLL clock definitions. Patch 10: - Set GMAC0 related clocks and RTC oscillator as optional inputs. - Sorted the clocks. Patch 11: - Replaced SOC_STARFIVE with ARCH_STARFIVE. - Added macros for PLL clocks and adjusted the code properly to make it easier to add the PLL clock driver later. - Updated the clock flags. Patch 12: - Built as a module by default. - Sorted the clocks. - Updated the clock flags. Patch 13: - Replaced "default CLK_STARFIVE_JH7110_SYS" with "default ARCH_STARFIVE". - Renamed "reset_info" struct to "jh7110_reset_info" and moved its definition into the driver. - Put jh7110_sys_info and jh7110_sys_info before the probe(). Patch 17: - Dropped "_zicsr" in ISA. - Sorted the external clocks alphabetically. - Put the ccache node before the plic node according to their addresses. - Sorted the clock inputs of the aoncrg node. Patch 19: - Replaced SOC_STARFIVE with ARCH_STARFIVE. - Sorted the nodes alphabetically. v4: https://lore.kernel.org/all/20230221024645.127922-1-hal.feng@xxxxxxxxxxxxxxxx/ Changes since v3: - Suggested by Conor, Merged clock & reset series and DT series together so that they could go via the same tree as the dt-binding headers are required by both driver & devicetree. - Rebased on tag v6.2. [Clock & reset] Patch 2: - Split patch 2 into two. One for renaming file and one for renaming variables. (by Conor) Patch 4: - Split patch 4 into two. One for code movement and one for extraction. (by Conor) Patch 5 & 9 & 10 & 11: - Fixed the issues reported by kernel test robot. Patch 9: - Set (&priv->base) as driver data instead of (priv->base). - Set the frequency of clock PLL0 as 1000MHz for Synchronizing with the lastest u-boot setting from StarFive. (by Emil) - Used devm_kzalloc() instead of kzalloc() when registering aux device. Patch 10: - Set (&priv->base) as driver data instead of (priv->base). Patch 11: - Used (*base) to get the register base address instead of (base). [Device tree] - Dropped patch 1, 4, 5 because they were accepted. - Added a new patch to add SiFive S7 compatible. (by Conor) - Added a new patch to add JH7110 pin function definitions. Patch 6: - Changed the label "S76_0" to "S7_0" and used compatible "sifive,s7" for core 0. - Updated ISA of each cores. (by Conor) - Made the node names generic. (by Krzysztof) - Added clock-output-names for all external clocks. - Added i2c0~6 nodes. - Changed the node name "gpio" to "pinctrl". Changed the label "gpio" and "gpioa" to "sysgpio" and "aongpio". (by Conor) Patch 7: - Separated the long lines into more lines in Makefile. (by Conor) - Renamed jh7110-starfive-visionfive-2-va.dts and jh7110-starfive-visionfive-2-vb.dts to jh7110-starfive-visionfive-2-v1.2a.dts and jh7110-starfive-visionfive-2-v1.3b.dts. Changed the model and compatible to match v1.2A and v1.3B which are printed on the silkscreen of VisionFive 2 board. (by Emil) - Configured pins for i2c0/2/5/6 and enabled them. clock & reset v3: https://lore.kernel.org/all/20221220005054.34518-1-hal.feng@xxxxxxxxxxxxxxxx/ DT v3: https://lore.kernel.org/all/20221220011247.35560-1-hal.feng@xxxxxxxxxxxxxxxx/ Changes since v2: [Clock & reset] - Rebased on tag v6.1. - Added "JH71X0" to the StarFive driver headers in MAINTAINERS. - Removed Co-developed-by tag of Hal in patch 1 and patch 4. - Changed the commit author from Hal to Emil in patch 2 and patch 5. Removed Co-developed-by tag of Emil in patch 2 and patch 5. (by Emil) - Improved the coding style of patch 11, 12 and 13. - Dropped patch 14. (by Emil) Patch 4: - Passed the "owner" member of reset_controller_dev structure directly in reset_starfive_jh7100_register(). (by Emil) - Added MAINTAINERS changes. Patch 7: - Split patch 7 into sys part and aon part. Merged them into patch 9 and patch 10 respectively. (by Krzysztof) - Renamed include/dt-bindings/clock/starfive-jh7110.h to include/dt-bindings/clock/starfive,jh7110-crg.h. (by Krzysztof) - Synchronized the definitions with the latest changes from Emil. Patch 8: - Split patch 8 into sys part and aon part. Merged them into patch 9 and patch 10 respectively. (by Krzysztof) - Renamed include/dt-bindings/reset/starfive-jh7110.h to include/dt-bindings/reset/starfive,jh7110-crg.h. (by Krzysztof) - Fixed the date of Copyright. (by Emil) - Dropped weird indentations. (by Krzysztof) - Synchronized the definitions with the latest changes from Emil. Patch 9: - Improved the description of clocks. (by Emil and Krzysztof) - Added MAINTAINERS changes. Patch 10: - Improved the description of clocks. (by Emil and Krzysztof) - Changed the clock-name "clk_rtc" to "rtc_osc" and "apb_bus_func" to "apb_bus". Patch 11: - Removed the flags of trace/debug clocks and set the flags of core clocks as CLK_IS_CRITICAL. (by Emil) - Deleted the extra 1-1 clocks and synchronized the clock tree with the latest changes from Emil. (by Emil) - Selected RESET_STARFIVE_JH7110 in Kconfig option CLK_STARFIVE_JH7110_SYS. Patch 12: - Changed the macro JH7110_AONCLK_RTC to JH7110_AONCLK_RTC_OSC and JH7110_AONCLK_APB_BUS_FUNC to JH7110_AONCLK_APB_BUS. - Synchronized the clock tree with the latest changes from Emil. - Set the MODULE_LICENSE as "GPL" according to commit bf7fbeeae6db. Patch 13: - Removed the "asserted" member in reset_info structure and always pass NULL when calling reset_starfive_jh71x0_register(). (by Emil) [Device tree] - Rebased on tag v6.1. - Dropped patch 8 because it was merged. Patch 1: - Made the links into "Link:" tags. (by Conor) - Corrected the board name to "VisionFive 2" instead of "VisionFive V2" and added compatibles for version A and version B of VisionFive 2. (by Emil) Patch 4: - Used "sifive,ccache0" compatible string to match. (by Conor) Patch 5: - Dropped "select SIFIVE_CCACHE" in config SOC_STARFIVE. (by Conor) - Dropped "starfive,jh7110-ccache" compatible in drivers/soc/sifive/sifive_ccache.c. Patch 6: - Removed all "clock-frequency = <0>". (by Conor) - Sorted the nodes after their addresses. (by Emil) - Renamed "clk_rtc" to "rtc_osc". - Added "sifive,ccache0" compatible in the cache-controller node. - Renamed "JH7110_SYSCLK_APB_BUS_FUNC" to "JH7110_SYSCLK_APB_BUS" and renamed "apb_bus_func" to "apb_bus". Renamed "JH7110_SYSCLK_IOMUX" to "JH7110_SYSCLK_IOMUX_APB". Renamed "JH7110_SYSRST_IOMUX" to "JH7110_SYSRST_IOMUX_APB". Renamed "JH7110_AONRST_AON_IOMUX" to "JH7110_AONRST_IOMUX". - Removed "reg-names" in gpio nodes. Patch 7: - Corrected the board name to "VisionFive 2" instead of "VisionFive V2". - Renamed jh7110-starfive-visionfive-v2.dts to jh7110-starfive-visionfive-2.dtsi. - Added dts for VisionFive 2 version A and version B boards. - In the chosen node, deleted "linux,initrd-start" and "linux,initrd-end" and changed the value of "stdout-path" to "serial0:115200n8". - Changed the bias of uart0 "rx-pins" to "bias-disable; /* external pull-up */". - Renamed "clk_rtc" to "rtc_osc". - Moved the gpio node behind the uart0 node. clock & reset v2: https://lore.kernel.org/all/20221118010627.70576-1-hal.feng@xxxxxxxxxxxxxxxx/ DT v2: https://lore.kernel.org/all/20221118011714.70877-1-hal.feng@xxxxxxxxxxxxxxxx/ Changes since v1: [Clock & reset] - Rebased on tag v6.1-rc5. - Rewrote the clock and reset drivers using auxiliary bus framework, so patch 8, 9, 15 were dropped and all patches changed a lot. (by Stephen) - Split Patch 14 into two patches. One is for factoring out the common JH71X0 code, the another one is for renaming. (by Stephen) - Created a subdirectory for StarFive reset drivers. - Factored out common JH71X0 reset code. - Renamed the common clock and reset code from "*starfive*" or "*STARFIVE*" to "*jh71x0*" or "*JH71X0*". - Combined JH7110 system and always-on clock DT binding headers in one file named "include/dt-bindings/clock/starfive-jh7110.h". - Renamed clock definitions "JH7110_SYSCLK_PCLK2_MUX_FUNC_PCLK" and "JH7110_SYSCLK_U2_PCLK_MUX_PCLK" to "JH7110_SYSCLK_PCLK2_MUX_FUNC" and "JH7110_SYSCLK_PCLK2_MUX". - Rewrote the DT bindings of clock and reset for using auxiliary bus. - Registered an auxiliary device for reset controller in clock drivers. - Changed clock names "CODAJ*" and "WAVE*" to "codaj*" and "wave*". Changed clock names "u2_pclk_mux_func_pclk" and "u2_pclk_mux_pclk" to "pclk2_mux_func" and "pclk2_mux". - Changed the flags of clock apb0 and noc_bus_isp_axi to CLK_IS_CRITICAL as suggested by StarFive SDK group. - Registered clock gmac0_gtxc as a gate clock instead of a div clock as suggested by StarFive SDK group. - Changed the frequency of clock pll2_out to 1188MHz as suggested by StarFive SDK group. - Fixed the bug that the clock JH7110_AONCLK_GMAC0_GTXCLK was not handled in JH7110 always-on clock driver. - Registered the reset driver as an auxiliary driver. - Reworded the commit messages. [Device tree] - Rebased on tag v6.1-rc5. - Added blank line in patch 1. (by Krzysztof) - Rebased patch 4 and 6 on the newest code. (by Conor) - Dropped patch 5. (by Conor) - Removed the quirk of JH7100 in patch 6, considering this patch series should only add support for JH7110. - For patch 27, added Co-developed-by tag for Jianlong and me. Renamed cpu labels to "S76_0", "U74_*" instead of "cpu*" following the style of jh7100.dtsi. Moved all "clock-frequency" properties to the board dts. Rewrote clock-controller nodes and deleted reset-controller nodes for using auxiliary bus. Rewrote gpio nodes following generic pinctrl bindings. Removed the redundant second reset entry of uart nodes. - For patch 28, added Co-developed-by tag for Jianlong and me. Added a chosen node. Removed reserved-memory node. Added fixed frequency clock nodes for overriding the "clock-frequency" properties. Rewrote the gpio nodes following generic pinctrl bindings. - Dropped patch 30. (by Conor) - Reworded the commit messages. v1: https://lore.kernel.org/all/20220929143225.17907-1-hal.feng@xxxxxxxxxxxxxxxxxxxxxx/ Emil Renner Berthing (16): clk: starfive: Factor out common JH7100 and JH7110 code clk: starfive: Rename clk-starfive-jh7100.h to clk-starfive-jh71x0.h clk: starfive: Rename "jh7100" to "jh71x0" for the common code reset: Create subdirectory for StarFive drivers reset: starfive: Factor out common JH71X0 reset code reset: starfive: Extract the common JH71X0 reset code reset: starfive: Rename "jh7100" to "jh71x0" for the common code reset: starfive: jh71x0: Use 32bit I/O on 32bit registers dt-bindings: clock: Add StarFive JH7110 system clock and reset generator dt-bindings: clock: Add StarFive JH7110 always-on clock and reset generator clk: starfive: Add StarFive JH7110 system clock driver clk: starfive: Add StarFive JH7110 always-on clock driver dt-bindings: timer: Add StarFive JH7110 clint dt-bindings: interrupt-controller: Add StarFive JH7110 plic riscv: dts: starfive: Add initial StarFive JH7110 device tree riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree Hal Feng (4): clk: starfive: Replace SOC_STARFIVE with ARCH_STARFIVE reset: starfive: Replace SOC_STARFIVE with ARCH_STARFIVE reset: starfive: Add StarFive JH7110 reset driver dt-bindings: riscv: Add SiFive S7 compatible Jianlong Huang (1): riscv: dts: starfive: Add StarFive JH7110 pin function definitions .../clock/starfive,jh7110-aoncrg.yaml | 107 +++ .../clock/starfive,jh7110-syscrg.yaml | 104 +++ .../sifive,plic-1.0.0.yaml | 1 + .../devicetree/bindings/riscv/cpus.yaml | 1 + .../bindings/timer/sifive,clint.yaml | 1 + MAINTAINERS | 22 +- arch/riscv/boot/dts/starfive/Makefile | 6 +- arch/riscv/boot/dts/starfive/jh7110-pinfunc.h | 308 ++++++++ .../jh7110-starfive-visionfive-2-v1.2a.dts | 13 + .../jh7110-starfive-visionfive-2-v1.3b.dts | 13 + .../jh7110-starfive-visionfive-2.dtsi | 215 ++++++ arch/riscv/boot/dts/starfive/jh7110.dtsi | 509 +++++++++++++ drivers/clk/Makefile | 2 +- drivers/clk/starfive/Kconfig | 33 +- drivers/clk/starfive/Makefile | 6 +- .../clk/starfive/clk-starfive-jh7100-audio.c | 74 +- drivers/clk/starfive/clk-starfive-jh7100.c | 716 +++++------------- drivers/clk/starfive/clk-starfive-jh7100.h | 112 --- .../clk/starfive/clk-starfive-jh7110-aon.c | 156 ++++ .../clk/starfive/clk-starfive-jh7110-sys.c | 450 +++++++++++ drivers/clk/starfive/clk-starfive-jh71x0.c | 383 ++++++++++ drivers/clk/starfive/clk-starfive-jh71x0.h | 131 ++++ drivers/reset/Kconfig | 8 +- drivers/reset/Makefile | 2 +- drivers/reset/reset-starfive-jh7100.c | 173 ----- drivers/reset/starfive/Kconfig | 20 + drivers/reset/starfive/Makefile | 5 + .../reset/starfive/reset-starfive-jh7100.c | 74 ++ .../reset/starfive/reset-starfive-jh7110.c | 70 ++ .../reset/starfive/reset-starfive-jh71x0.c | 131 ++++ .../reset/starfive/reset-starfive-jh71x0.h | 14 + .../dt-bindings/clock/starfive,jh7110-crg.h | 221 ++++++ .../dt-bindings/reset/starfive,jh7110-crg.h | 154 ++++ 33 files changed, 3370 insertions(+), 865 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-aoncrg.yaml create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml create mode 100644 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi create mode 100644 arch/riscv/boot/dts/starfive/jh7110.dtsi delete mode 100644 drivers/clk/starfive/clk-starfive-jh7100.h create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-aon.c create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-sys.c create mode 100644 drivers/clk/starfive/clk-starfive-jh71x0.c create mode 100644 drivers/clk/starfive/clk-starfive-jh71x0.h delete mode 100644 drivers/reset/reset-starfive-jh7100.c create mode 100644 drivers/reset/starfive/Kconfig create mode 100644 drivers/reset/starfive/Makefile create mode 100644 drivers/reset/starfive/reset-starfive-jh7100.c create mode 100644 drivers/reset/starfive/reset-starfive-jh7110.c create mode 100644 drivers/reset/starfive/reset-starfive-jh71x0.c create mode 100644 drivers/reset/starfive/reset-starfive-jh71x0.h create mode 100644 include/dt-bindings/clock/starfive,jh7110-crg.h create mode 100644 include/dt-bindings/reset/starfive,jh7110-crg.h base-commit: e8d018dd0257f744ca50a729e3d042cf2ec9da65 -- 2.38.1
