[PATCH V2 2/3] arm64: dts: ti: Add k3-am625-beagleplay

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Robert Nelson <robertcnelson@xxxxxxxxx>

BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.

This board family can be identified by the 24c32 eeprom:

[aa 55 33 ee 01 37 00 10  2e 00 42 45 41 47 4c 45  |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d  00 00 30 32 30 30 37 38  |PLAY-A0-..020078|]

https://beagleplay.org/
https://git.beagleboard.org/beagleplay/beagleplay

Signed-off-by: Robert Nelson <robertcnelson@xxxxxxxxx>
Co-developed-by: Nishanth Menon <nm@xxxxxx>
Signed-off-by: Nishanth Menon <nm@xxxxxx>
---
Changes since V1: (major cleanups listed below)
- Sign-off order fixup
- Cleanup of pre-production board to production board changes (uart,
  gpio pinmuxes, mikrobus)
- spi node is enabled for mikrobus
- dropped wakeup_rtc0 alias - should keep the series independent.
- ramoops address changed to give space for m4f firmware
- leds-2 linux,default-trigger dropped as not compliant with yaml
- formatting fixups
- dropped no-map from reserved memories, and dropped redundant
  "OP-TEE" documentation.

V1: https://lore.kernel.org/all/20230311111022.23717-3-nm@xxxxxx/

 arch/arm64/boot/dts/ti/Makefile               |   1 +
 .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 757 ++++++++++++++++++
 2 files changed, 758 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 6acd12409d59..09b4eafd5716 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -9,6 +9,7 @@
 # alphabetically.
 
 # Boards with AM62x SoC
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
 
 # Boards with AM62Ax SoC
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
new file mode 100644
index 000000000000..f75e79e54dfc
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -0,0 +1,757 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * https://beagleplay.org/
+ *
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2022-2023 Robert Nelson, BeagleBoard.org Foundation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "k3-am625.dtsi"
+
+/ {
+	compatible =  "beagle,am625-beagleplay", "ti,am625";
+	model = "BeagleBoard.org BeaglePlay";
+
+	aliases {
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+		gpio0 = &main_gpio0;
+		gpio1 = &main_gpio1;
+		gpio2 = &mcu_gpio0;
+		i2c0 = &main_i2c0;
+		i2c1 = &main_i2c1;
+		i2c2 = &main_i2c2;
+		i2c3 = &main_i2c3;
+		i2c4 = &wkup_i2c0;
+		i2c5 = &mcu_i2c0;
+		mdio-gpio0 = &mdio0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		mmc2 = &sdhci2;
+		rtc0 = &rtc;
+		serial0 = &main_uart5;
+		serial1 = &main_uart6;
+		serial2 = &main_uart0;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops: ramoops@9ca00000 {
+			compatible = "ramoops";
+			reg = <0x00 0x9c700000 0x00 0x00100000>;
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x00>;
+			pmsg-size = <0x8000>;
+		};
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+	};
+
+	vsys_5v0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3: regulator-2 {
+		/* output of TLV62595DMQR-U12 */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vsys_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wlan_en: regulator-3 {
+		/* OUTPUT of SN74AVC2T244DQMR */
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&vdd_3v3>;
+		gpio = <&main_gpio0 38 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_pins_default>;
+	};
+
+	vdd_3v3_sd: regulator-4 {
+		/* output of TPS22918DBVR-U21 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_3v3_sd_pins_default>;
+
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&vdd_3v3>;
+		gpio = <&main_gpio1 19 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: regulator-5 {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_hs200_switch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vdd_3v3>;
+		gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			gpios = <&main_gpio0 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+
+		led-1 {
+			gpios = <&main_gpio0 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			default-state = "keep";
+		};
+
+		led-2 {
+			gpios = <&main_gpio0 5 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_CPU;
+		};
+
+		led-3 {
+			gpios = <&main_gpio0 6 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_LAN;
+		};
+
+		led-4 {
+			gpios = <&main_gpio0 9 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_WLAN;
+		};
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usr_button_pins_default>;
+
+		usr: button-usr {
+			label = "User Key";
+			linux,code = <BTN_0>;
+			gpios = <&main_gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+
+	};
+
+	/* Workaround for errata i2329 - just use mdio bitbang */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mdio0_pins_default>;
+		gpios = <&main_gpio0 86 GPIO_ACTIVE_HIGH>, /* MDC */
+			<&main_gpio0 85 GPIO_ACTIVE_HIGH>; /* MDIO */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpsw3g_phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		cpsw3g_phy1: ethernet-phy@1 {
+			reg = <1>;
+			reset-gpios = <&main_gpio1 5 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <25>;
+			reset-deassert-us = <60000>; /* T2 */
+		};
+	};
+};
+
+&main_pmx0 {
+	gpio0_pins_default: gpio0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0004, PIN_INPUT, 7) /* (G25) OSPI0_LBCLKO.GPIO0_1 */
+			AM62X_IOPAD(0x0008, PIN_INPUT, 7) /* (J24) OSPI0_DQS.GPIO0_2 */
+			AM62X_IOPAD(0x000c, PIN_INPUT, 7) /* (E25) OSPI0_D0.GPIO0_3 */
+			AM62X_IOPAD(0x0010, PIN_INPUT, 7) /* (G24) OSPI0_D1.GPIO0_4 */
+			AM62X_IOPAD(0x0014, PIN_INPUT, 7) /* (F25) OSPI0_D2.GPIO0_5 */
+			AM62X_IOPAD(0x0018, PIN_INPUT, 7) /* (F24) OSPI0_D3.GPIO0_6 */
+			AM62X_IOPAD(0x0024, PIN_INPUT, 7) /* (H25) OSPI0_D6.GPIO0_9 */
+			AM62X_IOPAD(0x0028, PIN_INPUT, 7) /* (J22) OSPI0_D7.GPIO0_10 */
+			AM62X_IOPAD(0x002c, PIN_INPUT, 7) /* (F23) OSPI0_CSn0.GPIO0_11 */
+			AM62X_IOPAD(0x0030, PIN_INPUT, 7) /* (G21) OSPI0_CSn1.GPIO0_12 */
+			AM62X_IOPAD(0x0034, PIN_INPUT, 7) /* (H21) OSPI0_CSn2.GPIO0_13 */
+			AM62X_IOPAD(0x0038, PIN_INPUT, 7) /* (E24) OSPI0_CSn3.GPIO0_14 */
+			AM62X_IOPAD(0x00a4, PIN_INPUT, 7) /* (M22) GPMC0_DIR.GPIO0_40 */
+			AM62X_IOPAD(0x00ac, PIN_INPUT, 7) /* (L21) GPMC0_CSn1.GPIO0_42 */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
+		>;
+	};
+
+	usr_button_pins_default: usr-button-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0048, PIN_INPUT, 7) /* (N25) GPMC0_AD3.GPIO0_18 */
+		>;
+	};
+
+	grove_pins_default: grove-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
+			AM62X_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
+		>;
+	};
+
+	local_i2c_pins_default: local-i2c-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
+			AM62X_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
+		>;
+	};
+
+	i2c2_1v8_pins_default: i2c2-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
+			AM62X_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	mdio0_pins_default: mdio0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0160, PIN_OUTPUT, 7) /* (AD24) MDIO0_MDC.GPIO0_86 */
+			AM62X_IOPAD(0x015c, PIN_INPUT, 7) /* (AB22) MDIO0_MDIO.GPIO0_85 */
+		>;
+	};
+
+	rgmii1_pins_default: rgmii1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x014c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
+			AM62X_IOPAD(0x0150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
+			AM62X_IOPAD(0x0154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
+			AM62X_IOPAD(0x0158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
+			AM62X_IOPAD(0x0148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
+			AM62X_IOPAD(0x0144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
+			AM62X_IOPAD(0x0134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
+			AM62X_IOPAD(0x0138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
+			AM62X_IOPAD(0x013c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
+			AM62X_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
+			AM62X_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
+			AM62X_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
+		>;
+	};
+
+	emmc_pins_default: emmc-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+			AM62X_IOPAD(0x0218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+			AM62X_IOPAD(0x0214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+			AM62X_IOPAD(0x0210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
+			AM62X_IOPAD(0x020c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
+			AM62X_IOPAD(0x0208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
+			AM62X_IOPAD(0x0204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
+			AM62X_IOPAD(0x0200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
+			AM62X_IOPAD(0x01fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
+			AM62X_IOPAD(0x01f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
+		>;
+	};
+
+	vdd_3v3_sd_pins_default: vdd-3v3-sd-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01c4, PIN_INPUT, 7) /* (B14) SPI0_D1_GPIO1_19 */
+		>;
+	};
+
+	sd_pins_default: sd-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x023c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
+			AM62X_IOPAD(0x0234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
+			AM62X_IOPAD(0x0230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
+			AM62X_IOPAD(0x022c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
+			AM62X_IOPAD(0x0228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
+			AM62X_IOPAD(0x0224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
+			AM62X_IOPAD(0x0240, PIN_INPUT, 7) /* (D17) MMC1_SDCD.GPIO1_48 */
+		>;
+	};
+
+	wifi_pins_default: wifi-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0120, PIN_INPUT, 0) /* (C24) MMC2_CMD */
+			AM62X_IOPAD(0x0118, PIN_INPUT, 0) /* (D25) MMC2_CLK */
+			AM62X_IOPAD(0x0114, PIN_INPUT, 0) /* (B24) MMC2_DAT0 */
+			AM62X_IOPAD(0x0110, PIN_INPUT, 0) /* (C25) MMC2_DAT1 */
+			AM62X_IOPAD(0x010c, PIN_INPUT, 0) /* (E23) MMC2_DAT2 */
+			AM62X_IOPAD(0x0108, PIN_INPUT, 0) /* (D24) MMC2_DAT3 */
+			AM62X_IOPAD(0x0124, PIN_INPUT, 0) /* (A23) MMC2_SDCD */
+			AM62X_IOPAD(0x11c, PIN_INPUT, 0) /* (#N/A) MMC2_CLKB */
+		>;
+	};
+
+	wifi_en_pins_default: wifi-en-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x009c, PIN_OUTPUT, 7) /* (V25) GPMC0_WAIT1.GPIO0_38 */
+		>;
+	};
+
+	wifi_wlirq_pins_default: wifi-wlirq-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x00a8, PIN_INPUT, 7) /* (M21) GPMC0_CSn0.GPIO0_41 */
+		>;
+	};
+
+	spe_pins_default: spe-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0168, PIN_INPUT, 1) /* (AE21) RGMII2_TXC.RMII2_CRS_DV */
+			AM62X_IOPAD(0x0180, PIN_INPUT, 1) /* (AD23) RGMII2_RXC.RMII2_REF_CLK */
+			AM62X_IOPAD(0x0184, PIN_INPUT, 1) /* (AE23) RGMII2_RD0.RMII2_RXD0 */
+			AM62X_IOPAD(0x0188, PIN_INPUT, 1) /* (AB20) RGMII2_RD1.RMII2_RXD1 */
+			AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
+			AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
+			AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
+			AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
+			AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
+			AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
+			AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
+		>;
+	};
+
+	mikrobus_i2c_pins_default: mikrobus-i2c-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01d0, PIN_INPUT_PULLUP, 2) /* (A15) UART0_CTSn.I2C3_SCL */
+			AM62X_IOPAD(0x01d4, PIN_INPUT_PULLUP, 2) /* (B15) UART0_RTSn.I2C3_SDA */
+		>;
+	};
+
+	mikrobus_uart_pins_default: mikrobus-uart-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01d8, PIN_INPUT, 1) /* (C15) MCAN0_TX.UART5_RXD */
+			AM62X_IOPAD(0x01dc, PIN_OUTPUT, 1) /* (E15) MCAN0_RX.UART5_TXD */
+		>;
+	};
+
+	mikrobus_spi_pins_default: mikrobus-spi-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01b0, PIN_INPUT, 1) /* (A20) MCASP0_ACLKR.SPI2_CLK */
+			AM62X_IOPAD(0x01ac, PIN_INPUT, 1) /* (E19) MCASP0_AFSR.SPI2_CS0 */
+			AM62X_IOPAD(0x0194, PIN_INPUT, 1) /* (B19) MCASP0_AXR3.SPI2_D0 */
+			AM62X_IOPAD(0x0198, PIN_INPUT, 1) /* (A19) MCASP0_AXR2.SPI2_D1 */
+		>;
+	};
+
+	mikrobus_gpio_pins_default: mikrobus-gpio-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x019c, PIN_INPUT, 7) /* (B18) MCASP0_AXR1.GPIO1_9 */
+			AM62X_IOPAD(0x01a0, PIN_INPUT, 7) /* (E18) MCASP0_AXR0.GPIO1_10 */
+			AM62X_IOPAD(0x01a8, PIN_INPUT, 7) /* (D20) MCASP0_AFSX.GPIO1_12 */
+		>;
+	};
+
+	console_pins_default: console-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
+			AM62X_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
+		>;
+	};
+
+	wifi_debug_uart_pins_default: wifi-debug-uart-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x001c, PIN_INPUT, 3) /* (J23) OSPI0_D4.UART6_RXD */
+			AM62X_IOPAD(0x0020, PIN_OUTPUT, 3) /* (J25) OSPI0_D5.UART6_TXD */
+		>;
+	};
+
+	usb1_pins_default: usb1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0258, PIN_INPUT, 0) /* (F18) USB1_DRVVBUS */
+		>;
+	};
+
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (D16) EXTINTn */
+		>;
+	};
+};
+
+&mcu_pmx0 {
+	i2c_qwiic_pins_default: i2c-qwiic-pins-default {
+		pinctrl-single,pins = <
+			AM62X_MCU_IOPAD(0x0044, PIN_INPUT, 0) /* (A8) MCU_I2C0_SCL */
+			AM62X_MCU_IOPAD(0x0048, PIN_INPUT, 0) /* (D10) MCU_I2C0_SDA */
+		>;
+	};
+
+	gbe_pmx_obsclk: gbe-pmx-clk-default {
+		pinctrl-single,pins = <
+			AM62X_MCU_IOPAD(0x0004, PIN_OUTPUT, 1) /* (B8) MCU_SPI0_CS1.MCU_OBSCLK0 */
+		>;
+	};
+
+	i2c_csi_pins_default: i2c-csi-pins-default {
+		pinctrl-single,pins = <
+			AM62X_MCU_IOPAD(0x004c, PIN_INPUT_PULLUP, 0) /* (B9) WKUP_I2C0_SCL */
+			AM62X_MCU_IOPAD(0x0050, PIN_INPUT_PULLUP, 0) /* (A9) WKUP_I2C0_SDA */
+		>;
+	};
+
+	wifi_32k_clk: mcu-clk-out-pins-default {
+		pinctrl-single,pins = <
+			AM62X_MCU_IOPAD(0x0084, PIN_OUTPUT, 0) /* (A12) WKUP_CLKOUT0 */
+		>;
+	};
+};
+
+&a53_opp_table {
+	/* Requires VDD_CORE to be at 0.85V */
+	opp-1400000000 {
+		opp-hz = /bits/ 64 <1400000000>;
+		opp-supported-hw = <0x01 0x0004>;
+	};
+};
+
+&wkup_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_csi_pins_default>;
+	clock-frequency = <400000>;
+	/* Enable with overlay for camera sensor */
+};
+
+&mcu_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_qwiic_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&usbss0 {
+	ti,vbus-divider;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+};
+
+&usbss1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_default>;
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_pins_default>, <&spe_pins_default>,
+		    <&gbe_pmx_obsclk>;
+	assigned-clocks = <&k3_clks 157 70>, <&k3_clks 157 20>;
+	assigned-clock-parents = <&k3_clks 157 72>, <&k3_clks 157 22>;
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+	phy-mode = "rmii";
+	phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+	/* Workaround for errata i2329 - Use mdio bitbang */
+	status = "disabled";
+};
+
+&main_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio0_pins_default>;
+	gpio-line-names = "BL_EN_3V3", "SPE_PO_EN", "RTC_INT",	/* 0-2 */
+		"USR0", "USR1", "USR2", "USR3", "", "", "USR4",	/* 3-9 */
+		"EEPROM_WP",					/* 10 */
+		"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2",	/* 11-12 */
+		"CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "",	/* 13-17 */
+		"USR_BUTTON", "", "", "", "", "", "", "", "",	/* 18-26 */
+		"", "", "", "", "", "", "", "", "", "HDMI_INT",	/* 27-36 */
+		"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
+		"", "", "", "", "", "", "", "", "", "", "", "",	/* 43-54 */
+		"", "", "", "", "", "", "", "", "", "", "", "", /* 55-66 */
+		"", "", "", "", "", "", "", "", "", "", "", "", /* 67-78 */
+		"", "", "", "", "", "",				/* 79-84 */
+		"BITBANG_MDIO_DATA", "BITBANG_MDIO_CLK",	/* 85-86 */
+		"", "", "", "", "";				/* 87-91 */
+};
+
+&main_gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mikrobus_gpio_pins_default>;
+	gpio-line-names = "", "", "", "", "",			/* 0-4 */
+		"SPE_RSTN", "SPE_INTN", "MIKROBUS_GPIO1_7",	/* 5-7 */
+		"MIKROBUS_GPIO1_8", "MIKROBUS_GPIO1_9",		/* 8-9 */
+		"MIKROBUS_GPIO1_10", "MIKROBUS_GPIO1_11",	/* 10-11 */
+		"MIKROBUS_GPIO1_12", "MIKROBUS_W1_GPIO0",	/* 12-13 */
+		"MIKROBUS_GPIO1_14",				/* 14 */
+		"", "", "", "", "VDD_3V3_SD", "", "",		/* 15-21 */
+		"MIKROBUS_GPIO1_22", "MIKROBUS_GPIO1_23",	/* 22-23 */
+		"MIKROBUS_GPIO1_24", "MIKROBUS_GPIO1_25",	/* 24-25 */
+		"", "", "", "", "", "", "", "", "", "", "", "",	/* 26-37 */
+		"", "", "", "", "", "", "", "", "", "",		/* 38-47 */
+		"SD_CD", "SD_VOLT_SEL", "", "";			/* 48-51 */
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&local_i2c_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "ti,bq32000";
+		reg = <0x68>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	tps65219: pmic@30 {
+		compatible = "ti,tps65219";
+		reg = <0x30>;
+		buck1-supply = <&vsys_5v0>;
+		buck2-supply = <&vsys_5v0>;
+		buck3-supply = <&vsys_5v0>;
+		ldo1-supply = <&vdd_3v3>;
+		ldo2-supply = <&buck2_reg>;
+		ldo3-supply = <&vdd_3v3>;
+		ldo4-supply = <&vdd_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		system-power-controller;
+		ti,power-button;
+
+		regulators {
+			buck1_reg: buck1 {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck2_reg: buck2 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck3_reg: buck3 {
+				regulator-name = "VDD_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				/*
+				 * Regulator is left as is unused, vdd_sd
+				 * is controlled via GPIO with bypass config
+				 * as per the NVM configuration
+				 */
+				regulator-name = "VDD_SD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-allow-bypass;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-name = "VDDA_0V85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: ldo3 {
+				regulator-name = "VDDA_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: ldo4 {
+				regulator-name = "VDD_2V5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&grove_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&main_i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_1v8_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&main_i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mikrobus_i2c_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&main_spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mikrobus_spi_pins_default>;
+	status = "okay";
+};
+
+&sdhci0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+	status = "okay";
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd_pins_default>;
+
+	vmmc-supply = <&vdd_3v3_sd>;
+	vqmmc-supply = <&vdd_sd_dv>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+	cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
+	cd-debounce-delay-ms = <100>;
+	ti,fails-without-test-cd;
+	status = "okay";
+};
+
+&sdhci2 {
+	vmmc-supply = <&wlan_en>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&wifi_pins_default>, <&wifi_32k_clk>;
+	bus-width = <4>;
+	non-removable;
+	ti,fails-without-test-cd;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,driver-strength-ohm = <50>;
+	assigned-clocks = <&k3_clks 157 158>;
+	assigned-clock-parents = <&k3_clks 157 160>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1807";
+		reg = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_wlirq_pins_default>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <41 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&console_pins_default>;
+	status = "okay";
+};
+
+&main_uart1 {
+	/* Main UART1 is used by TIFS firmware */
+	status = "reserved";
+};
+
+&main_uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mikrobus_uart_pins_default>;
+	status = "okay";
+};
+
+&main_uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wifi_debug_uart_pins_default>;
+	status = "okay";
+};
-- 
2.40.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux