On 15.03.2023 06:12, Nikita Travkin wrote:
> Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform.
>
> The laptop design is similar to trogdor in the choice of primary
> components but the specifics on usage of those differ slightly.
>
> Add the devicetree for the laptop with support for most of the
> hardware present.
>
> Signed-off-by: Nikita Travkin <nikita@xxxxxxx>
> ---
[...]
> +
> +&camcc {
> + status = "disabled";
> +};
Any particular reason? The clocks should park themselves and
not even waste power
> +
> +&dsi0 {
> + vdda-supply = <&vreg_l3c_1p2>;
> + status = "okay";
> +};
[...]
> +
> + touchpad@2c {
> + compatible = "hid-over-i2c";
> + reg = <0x2c>;
> + hid-descr-addr = <0x20>;
> +
> + vdd-supply = <®_tp_3p3>;
> +
> + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>;
> +
> + pinctrl-0 = <&hid_touchpad_default>;
> + pinctrl-names = "default";
> + };
No wakeup-source on the touchpad? My (different) laptop wakes
up when I press on it
> +
> + keyboard@3a {
> + compatible = "hid-over-i2c";
> + reg = <0x3a>;
[...]
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&zap_mem>;
> + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn";
qcom/sc7180/acer/(aspire1|alice)/qc..
?
> + };
> +};
> +
> +/* Seems like ADSP really insists on managing those lpass bits itself */
> +&lpasscc {
> + status = "disabled";
> +};
> +
> +&lpass_hm {
> + status = "disabled";
> +};
These clocks are only accessible from HLOS on Chrome devices. I'd say
disabling them by default in sc7180.dtsi would be sensible.
> +
> +&mdp {
> + status = "okay";
> +};
Remove the status=disabled from SoC DT, MDSS is useless without MDP and
one toggle is enough.
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&pm6150_adc {
> + thermistor@4e {
> + reg = <ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + };
> +
> + charger-thermistor@4f {
> + reg = <ADC5_AMUX_THM3_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + };
> +};
> +
> +&pm6150_adc_tm {
> + status = "okay";
> +
> + charger-thermistor@0 {
> + reg = <0>;
> + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + thermistor@1 {
> + reg = <1>;
> + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +};
> +
> +&pm6150_pon { status = "disabled"; };
Not even for reboot control?
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
[...]
> +
> +&usb_1_hsphy {
> + vdd-supply = <&vreg_l4a_0p8>;
> + vdda-pll-supply = <&vreg_l11a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
> + qcom,imp-res-offset-value = <8>;
> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> + qcom,bias-ctrl-value = <0x22>;
> + qcom,charge-ctrl-value = <3>;
> + qcom,hsdisc-trim-value = <0>;
> +
> + status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vreg_l4a_0p8>;
> + status = "okay";
Please be consistent with newlines before status.
> +};
> +
> +&venus {
> + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn";
See previous note about the firmware path
> +};
> +
> +&wifi {
> + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
> + vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
> + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
> + status = "okay";
> +};
[...]
> +
> + vreg_l10a_1p8: ldo10 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +
Unexpected newline
Konrad
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vreg_l11a_1p8: ldo11 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a_1p8: ldo13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l14a_1p8: ldo14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l15a_1p8: ldo15 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l16a_2p7: ldo16 {
> + regulator-min-microvolt = <2496000>;
> + regulator-max-microvolt = <3304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l17a_3p0: ldo17 {
> + regulator-min-microvolt = <2920000>;
> + regulator-max-microvolt = <3232000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l18a_2p8: ldo18 {
> + regulator-min-microvolt = <2496000>;
> + regulator-max-microvolt = <3304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l19a_2p9: ldo19 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pm6150l-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vreg_s8c_1p3: smps8 {
> + regulator-min-microvolt = <1120000>;
> + regulator-max-microvolt = <1408000>;
> + };
> +
> + vreg_l1c_1p8: ldo1 {
> + regulator-min-microvolt = <1616000>;
> + regulator-max-microvolt = <1984000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2c_1p3: ldo2 {
> + regulator-min-microvolt = <1168000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3c_1p2: ldo3 {
> + regulator-min-microvolt = <1144000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4c_1p8: ldo4 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <3304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + };
> +
> + vreg_l5c_1p8: ldo5 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <3304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + };
> +
> + vreg_l6c_2p9: ldo6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7c_3p0: ldo7 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + };
> +
> + vreg_l8c_1p8: ldo8 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9c_2p9: ldo9 {
> + regulator-min-microvolt = <2952000>;
> + regulator-max-microvolt = <2952000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10c_3p3: ldo10 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l11c_3p3: ldo11 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_bob: bob {
> + regulator-min-microvolt = <3008000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> + };
> + };
> +};
> +
> +&qup_i2c2_default {
> + drive-strength = <2>;
> +
> + /* Has external pullup */
> + bias-disable;
> +};
> +
> +&qup_i2c4_default {
> + drive-strength = <2>;
> +
> + /* Has external pullup */
> + bias-disable;
> +};
> +
> +&qup_i2c9_default {
> + drive-strength = <2>;
> +
> + /* Has external pullup */
> + bias-disable;
> +};
> +
> +&qup_i2c10_default {
> + drive-strength = <2>;
> +
> + /* Has external pullup */
> + bias-disable;
> +};
> +
> +&tlmm {
> + /*
> + * The TZ seem to protect those because some boards can have
> + * fingerprint sensor connected to this range. Not connected
> + * on this board
> + */
> + gpio-reserved-ranges = <58 5>;
> +
> + amp_sd_mode_default: amp-sd-mode-deault-state {
> + pins = "gpio23";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + bridge_en_default: bridge-en-default-state {
> + pins = "gpio51";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + bridge_suspend_default: bridge-suspend-default-state {
> + pins = "gpio22";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-pull-up;
> + };
> +
> + codec_irq_default: codec-irq-deault-state {
> + pins = "gpio28";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + edp_bridge_irq_default: edp-bridge-irq-default-state {
> + pins = "gpio11";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + hid_keyboard_default: hid-keyboard-default-state {
> + pins = "gpio33";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + hid_touchpad_default: hid-touchpad-default-state {
> + pins = "gpio94";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + qup_uart3_sleep: qup-uart3-sleep-state {
> + cts-pins {
> + /*
> + * Configure a pull-down on CTS to match the pull of
> + * the Bluetooth module.
> + */
> + pins = "gpio38";
> + function = "gpio";
> + bias-pull-down;
> + };
> +
> + rts-pins {
> + /*
> + * Configure pull-down on RTS. As RTS is active low
> + * signal, pull it low to indicate the BT SoC that it
> + * can wakeup the system anytime from suspend state by
> + * pulling RX low (by sending wakeup bytes).
> + */
> + pins = "gpio39";
> + function = "gpio";
> + bias-pull-down;
> + };
> +
> + tx-pins {
> + /*
> + * Configure pull-up on TX when it isn't actively driven
> + * to prevent BT SoC from receiving garbage during sleep.
> + */
> + pins = "gpio40";
> + function = "gpio";
> + bias-pull-up;
> + };
> +
> + rx-pins {
> + /*
> + * Configure a pull-up on RX. This is needed to avoid
> + * garbage data when the TX pin of the Bluetooth module
> + * is floating which may cause spurious wakeups.
> + */
> + pins = "gpio41";
> + function = "gpio";
> + bias-pull-up;
> + };
> + };
> +
> + reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state {
> + pins = "gpio19";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state {
> + pins = "gpio20";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + reg_lcm_en_default: reg-lcm-en-deault-state {
> + pins = "gpio26";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + reg_audio_en_default: reg-audio-en-deault-state {
> + pins = "gpio83";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + reg_tp_en_default: reg-tp-en-deault-state {
> + pins = "gpio25";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + soc_bkoff_default: soc-bkoff-deault-state {
> + pins = "gpio10";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + sdc1_default: sdc1-default-state {
> + clk-pins {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + cmd-pins {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <16>;
> + };
> +
> + data-pins {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <16>;
> + };
> +
> + rclk-pins {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + sdc1_sleep: sdc1-sleep-state {
> + clk-pins {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
> + cmd-pins {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + data-pins {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + rclk-pins {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + ter_mi2s_active: ter-mi2s-active-state {
> + pins = "gpio63", "gpio64", "gpio65";
> + function = "mi2s_2";
> + };
> +};
