[PATCH v4 11/18] PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.

It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.

The total number of resets supported is 12 but only ipq4019 is using all of
them.

Tested-by: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 238 ++++---------------------
 1 file changed, 30 insertions(+), 208 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 8c39fc554a89..ed43e03b972f 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -176,22 +176,13 @@ struct qcom_pcie_resources_2_3_3 {
 	struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
 };
 
-#define QCOM_PCIE_2_4_0_MAX_CLOCKS	4
+#define QCOM_PCIE_2_4_0_MAX_CLOCKS		4
+#define QCOM_PCIE_2_4_0_MAX_RESETS		12
 struct qcom_pcie_resources_2_4_0 {
 	struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
 	int num_clks;
-	struct reset_control *axi_m_reset;
-	struct reset_control *axi_s_reset;
-	struct reset_control *pipe_reset;
-	struct reset_control *axi_m_vmid_reset;
-	struct reset_control *axi_s_xpu_reset;
-	struct reset_control *parf_reset;
-	struct reset_control *phy_reset;
-	struct reset_control *axi_m_sticky_reset;
-	struct reset_control *pipe_sticky_reset;
-	struct reset_control *pwr_reset;
-	struct reset_control *ahb_reset;
-	struct reset_control *phy_ahb_reset;
+	struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
+	int num_resets;
 };
 
 /* 6 clocks typically, 7 for sm8250 */
@@ -626,65 +617,24 @@ static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie)
 	if (ret < 0)
 		return ret;
 
-	res->axi_m_reset = devm_reset_control_get_exclusive(dev, "axi_m");
-	if (IS_ERR(res->axi_m_reset))
-		return PTR_ERR(res->axi_m_reset);
-
-	res->axi_s_reset = devm_reset_control_get_exclusive(dev, "axi_s");
-	if (IS_ERR(res->axi_s_reset))
-		return PTR_ERR(res->axi_s_reset);
-
-	if (is_ipq) {
-		/*
-		 * These resources relates to the PHY or are secure clocks, but
-		 * are controlled here for IPQ4019
-		 */
-		res->pipe_reset = devm_reset_control_get_exclusive(dev, "pipe");
-		if (IS_ERR(res->pipe_reset))
-			return PTR_ERR(res->pipe_reset);
-
-		res->axi_m_vmid_reset = devm_reset_control_get_exclusive(dev,
-									 "axi_m_vmid");
-		if (IS_ERR(res->axi_m_vmid_reset))
-			return PTR_ERR(res->axi_m_vmid_reset);
-
-		res->axi_s_xpu_reset = devm_reset_control_get_exclusive(dev,
-									"axi_s_xpu");
-		if (IS_ERR(res->axi_s_xpu_reset))
-			return PTR_ERR(res->axi_s_xpu_reset);
-
-		res->parf_reset = devm_reset_control_get_exclusive(dev, "parf");
-		if (IS_ERR(res->parf_reset))
-			return PTR_ERR(res->parf_reset);
-
-		res->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
-		if (IS_ERR(res->phy_reset))
-			return PTR_ERR(res->phy_reset);
-	}
-
-	res->axi_m_sticky_reset = devm_reset_control_get_exclusive(dev,
-								   "axi_m_sticky");
-	if (IS_ERR(res->axi_m_sticky_reset))
-		return PTR_ERR(res->axi_m_sticky_reset);
-
-	res->pipe_sticky_reset = devm_reset_control_get_exclusive(dev,
-								  "pipe_sticky");
-	if (IS_ERR(res->pipe_sticky_reset))
-		return PTR_ERR(res->pipe_sticky_reset);
-
-	res->pwr_reset = devm_reset_control_get_exclusive(dev, "pwr");
-	if (IS_ERR(res->pwr_reset))
-		return PTR_ERR(res->pwr_reset);
-
-	res->ahb_reset = devm_reset_control_get_exclusive(dev, "ahb");
-	if (IS_ERR(res->ahb_reset))
-		return PTR_ERR(res->ahb_reset);
+	res->resets[0].id = "axi_m";
+	res->resets[1].id = "axi_s";
+	res->resets[2].id = "axi_m_sticky";
+	res->resets[3].id = "pipe_sticky";
+	res->resets[4].id = "pwr";
+	res->resets[5].id = "ahb";
+	res->resets[6].id = "pipe";
+	res->resets[7].id = "axi_m_vmid";
+	res->resets[8].id = "axi_s_xpu";
+	res->resets[9].id = "parf";
+	res->resets[10].id = "phy";
+	res->resets[11].id = "phy_ahb";
+
+	res->num_resets = is_ipq ? 12 : 6;
 
-	if (is_ipq) {
-		res->phy_ahb_reset = devm_reset_control_get_exclusive(dev, "phy_ahb");
-		if (IS_ERR(res->phy_ahb_reset))
-			return PTR_ERR(res->phy_ahb_reset);
-	}
+	ret = devm_reset_control_bulk_get_exclusive(dev, res->num_resets, res->resets);
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
@@ -693,15 +643,7 @@ static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;
 
-	reset_control_assert(res->axi_m_reset);
-	reset_control_assert(res->axi_s_reset);
-	reset_control_assert(res->pipe_reset);
-	reset_control_assert(res->pipe_sticky_reset);
-	reset_control_assert(res->phy_reset);
-	reset_control_assert(res->phy_ahb_reset);
-	reset_control_assert(res->axi_m_sticky_reset);
-	reset_control_assert(res->pwr_reset);
-	reset_control_assert(res->ahb_reset);
+	reset_control_bulk_assert(res->num_resets, res->resets);
 	clk_bulk_disable_unprepare(res->num_clks, res->clks);
 }
 
@@ -712,149 +654,29 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
 	struct device *dev = pci->dev;
 	int ret;
 
-	ret = reset_control_assert(res->axi_m_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert axi master reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->axi_s_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert axi slave reset\n");
-		return ret;
-	}
-
-	usleep_range(10000, 12000);
-
-	ret = reset_control_assert(res->pipe_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert pipe reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->pipe_sticky_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert pipe sticky reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->phy_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert phy reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->phy_ahb_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert phy ahb reset\n");
+	ret = reset_control_bulk_assert(res->num_resets, res->resets);
+	if (ret < 0) {
+		dev_err(dev, "cannot assert resets\n");
 		return ret;
 	}
 
 	usleep_range(10000, 12000);
 
-	ret = reset_control_assert(res->axi_m_sticky_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert axi master sticky reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->pwr_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert power reset\n");
-		return ret;
-	}
-
-	ret = reset_control_assert(res->ahb_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert ahb reset\n");
+	ret = reset_control_bulk_deassert(res->num_resets, res->resets);
+	if (ret < 0) {
+		dev_err(dev, "cannot deassert resets\n");
 		return ret;
 	}
 
 	usleep_range(10000, 12000);
 
-	ret = reset_control_deassert(res->phy_ahb_reset);
+	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
 	if (ret) {
-		dev_err(dev, "cannot deassert phy ahb reset\n");
+		reset_control_bulk_assert(res->num_resets, res->resets);
 		return ret;
 	}
 
-	ret = reset_control_deassert(res->phy_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert phy reset\n");
-		goto err_rst_phy;
-	}
-
-	ret = reset_control_deassert(res->pipe_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert pipe reset\n");
-		goto err_rst_pipe;
-	}
-
-	ret = reset_control_deassert(res->pipe_sticky_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert pipe sticky reset\n");
-		goto err_rst_pipe_sticky;
-	}
-
-	usleep_range(10000, 12000);
-
-	ret = reset_control_deassert(res->axi_m_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert axi master reset\n");
-		goto err_rst_axi_m;
-	}
-
-	ret = reset_control_deassert(res->axi_m_sticky_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert axi master sticky reset\n");
-		goto err_rst_axi_m_sticky;
-	}
-
-	ret = reset_control_deassert(res->axi_s_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert axi slave reset\n");
-		goto err_rst_axi_s;
-	}
-
-	ret = reset_control_deassert(res->pwr_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert power reset\n");
-		goto err_rst_pwr;
-	}
-
-	ret = reset_control_deassert(res->ahb_reset);
-	if (ret) {
-		dev_err(dev, "cannot deassert ahb reset\n");
-		goto err_rst_ahb;
-	}
-
-	usleep_range(10000, 12000);
-
-	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
-	if (ret)
-		goto err_clks;
-
 	return 0;
-
-err_clks:
-	reset_control_assert(res->ahb_reset);
-err_rst_ahb:
-	reset_control_assert(res->pwr_reset);
-err_rst_pwr:
-	reset_control_assert(res->axi_s_reset);
-err_rst_axi_s:
-	reset_control_assert(res->axi_m_sticky_reset);
-err_rst_axi_m_sticky:
-	reset_control_assert(res->axi_m_reset);
-err_rst_axi_m:
-	reset_control_assert(res->pipe_sticky_reset);
-err_rst_pipe_sticky:
-	reset_control_assert(res->pipe_reset);
-err_rst_pipe:
-	reset_control_assert(res->phy_reset);
-err_rst_phy:
-	reset_control_assert(res->phy_ahb_reset);
-	return ret;
 }
 
 static int qcom_pcie_post_init_2_4_0(struct qcom_pcie *pcie)
-- 
2.25.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux