Konrad Dybcio писал(а) 14.03.2023 15:24:
> On 14.03.2023 07:43, Nikita Travkin wrote:
>> Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform.
>>
>> The laptop design is similar to trogdor in the choice of primary
>> components but the specifics on usage of those differ slightly.
>>
>> Add the devicetree for the laptop with support for most of the
>> hardware present.
>>
>> Signed-off-by: Nikita Travkin <nikita@xxxxxxx>
>> ---
> [...]
>> + /* HACK: Display fails with
>> + *
>> + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz
>> + * *ERROR* Link training failed, link is off (-5)
>> + *
>> + * if the power to the panel was ever cut
> Your ACPI tables mention a single FSTATE where this regulator is
> off, may be worth looking into at some point, perhaps you need
> a more in-depth en-/disable sequence.
>
Yes, I want to get to the bottom of this eventually, thus making
it clear this is a hack.
Thanks for looking at it!
Nikita
> Konrad
>> + */
>> + regulator-always-on;
>> +
>> + gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> +
>> + pinctrl-0 = <®_lcm_en_default>;
>> + pinctrl-names = "default";
>> + };
>> +
>> + reg_tp_3p3: touchpad-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "tp_3p3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> +
>> + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> +
>> + pinctrl-0 = <®_tp_en_default>;
>> + pinctrl-names = "default";
>> + };
>> +};
>> +
>> +&camcc { status = "disabled"; };
>> +
>> +&dsi0 {
>> + vdda-supply = <&vreg_l3c_1p2>;
>> + status = "okay";
>> +};
>> +
>> +&dsi0_out {
>> + remote-endpoint = <&sn65dsi86_in>;
>> + data-lanes = <0 1 2 3>;
>> +};
>> +
>> +&dsi_phy {
>> + vdds-supply = <&vreg_l4a_0p8>;
>> + status = "okay";
>> +};
>> +
>> +&i2c2 {
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + /* embedded-controller@76 */
>> +};
>> +
>> +&i2c4 {
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + /*
>> + * NOTE: DSDT defines two possible touchpads, other one is
>> + *
>> + * reg = <0x15>;
>> + * hid-descr-addr = <0x1>;
>> + */
>> +
>> + touchpad@2c {
>> + compatible = "hid-over-i2c";
>> + reg = <0x2c>;
>> + hid-descr-addr = <0x20>;
>> +
>> + vdd-supply = <®_tp_3p3>;
>> +
>> + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>;
>> +
>> + pinctrl-0 = <&hid_touchpad_default>;
>> + pinctrl-names = "default";
>> + };
>> +
>> + keyboard@3a {
>> + compatible = "hid-over-i2c";
>> + reg = <0x3a>;
>> + hid-descr-addr = <0x1>;
>> +
>> + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>;
>> +
>> + pinctrl-0 = <&hid_keyboard_default>;
>> + pinctrl-names = "default";
>> +
>> + wakeup-source;
>> + };
>> +};
>> +
>> +&i2c9 {
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + alc5682: codec@1a {
>> + compatible = "realtek,rt5682i";
>> + reg = <0x1a>;
>> +
>> + #sound-dai-cells = <1>;
>> +
>> + interrupt-parent = <&tlmm>;
>> + /*
>> + * This will get ignored because the interrupt type
>> + * is set in rt5682.c.
>> + */
>> + interrupts = <28 IRQ_TYPE_EDGE_BOTH>;
>> +
>> + pinctrl-0 = <&codec_irq_default>;
>> + pinctrl-names = "default";
>> +
>> + AVDD-supply = <&vreg_l15a_1p8>;
>> + MICVDD-supply = <®_codec_3p3>;
>> + VBAT-supply = <®_codec_3p3>;
>> +
>> + realtek,dmic1-data-pin = <1>;
>> + realtek,dmic1-clk-pin = <1>;
>> + realtek,jd-src = <1>;
>> + };
>> +};
>> +
>> +&i2c10 {
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + sn65dsi86_bridge: bridge@2c {
>> + compatible = "ti,sn65dsi86";
>> + reg = <0x2c>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + #pwm-cells = <1>;
>> +
>> + interrupt-parent = <&tlmm>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
>> + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
>> +
>> + pinctrl-0 = <&bridge_en_default>,
>> + <&edp_bridge_irq_default>,
>> + <&bridge_suspend_default>;
>> + pinctrl-names = "default";
>> +
>> + vpll-supply = <®_brij_1p8>;
>> + vccio-supply = <®_brij_1p8>;
>> + vcca-supply = <®_brij_1p2>;
>> + vcc-supply = <®_brij_1p2>;
>> +
>> + clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
>> + clock-names = "refclk";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + sn65dsi86_in: endpoint {
>> + remote-endpoint = <&dsi0_out>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + sn65dsi86_out: endpoint {
>> + data-lanes = <0 1>;
>> + remote-endpoint = <&panel_in_edp>;
>> + };
>> + };
>> + };
>> +
>> + aux-bus {
>> + panel: panel {
>> + compatible = "edp-panel";
>> + power-supply = <®_lcm_3p3>;
>> + backlight = <&backlight>;
>> +
>> + port {
>> + panel_in_edp: endpoint {
>> + remote-endpoint = <&sn65dsi86_out>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&gpu {
>> + status = "okay";
>> +
>> + zap-shader {
>> + memory-region = <&zap_mem>;
>> + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn";
>> + };
>> +};
>> +
>> +/* Seems like ADSP really insists on managing those itself */
>> +&lpasscc { status = "disabled"; };
>> +&lpass_hm { status = "disabled"; };
>> +
>> +&mdp {
>> + status = "okay";
>> +};
>> +
>> +&mdss {
>> + status = "okay";
>> +};
>> +
>> +&pm6150_adc {
>> + thermistor@4e {
>> + reg = <ADC5_AMUX_THM2_100K_PU>;
>> + qcom,ratiometric;
>> + qcom,hw-settle-time = <200>;
>> + };
>> +
>> + charger-thermistor@4f {
>> + reg = <ADC5_AMUX_THM3_100K_PU>;
>> + qcom,ratiometric;
>> + qcom,hw-settle-time = <200>;
>> + };
>> +};
>> +
>> +&pm6150_adc_tm {
>> + status = "okay";
>> +
>> + charger-thermistor@0 {
>> + reg = <0>;
>> + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
>> + qcom,ratiometric;
>> + qcom,hw-settle-time-us = <200>;
>> + };
>> +
>> + thermistor@1 {
>> + reg = <1>;
>> + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>;
>> + qcom,ratiometric;
>> + qcom,hw-settle-time-us = <200>;
>> + };
>> +};
>> +
>> +&pm6150_pon { status = "disabled"; };
>> +
>> +&qupv3_id_0 {
>> + status = "okay";
>> +};
>> +
>> +&qupv3_id_1 {
>> + status = "okay";
>> +};
>> +
>> +&remoteproc_mpss {
>> + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn";
>> + status = "okay";
>> +};
>> +
>> +&sdhc_1 {
>> + pinctrl-0 = <&sdc1_default>;
>> + pinctrl-1 = <&sdc1_sleep>;
>> + pinctrl-names = "default", "sleep";
>> + vmmc-supply = <&vreg_l19a_2p9>;
>> + vqmmc-supply = <&vreg_l12a_1p8>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&uart3 {
>> + /delete-property/interrupts;
>> + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
>> + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
>> +
>> + pinctrl-1 = <&qup_uart3_sleep>;
>> + pinctrl-names = "default", "sleep";
>> +
>> + status = "okay";
>> +
>> + bluetooth: bluetooth {
>> + compatible = "qcom,wcn3991-bt";
>> + vddio-supply = <&vreg_l10a_1p8>;
>> + vddxo-supply = <&vreg_l1c_1p8>;
>> + vddrf-supply = <&vreg_l2c_1p3>;
>> + vddch0-supply = <&vreg_l10c_3p3>;
>> + max-speed = <3200000>;
>> + };
>> +};
>> +
>> +&uart8 {
>> + status = "okay";
>> +};
>> +
>> +&usb_1 {
>> + status = "okay";
>> +};
>> +
>> +&usb_1_dwc3 {
>> + dr_mode = "host";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + usb_hub_2_x: hub@1 {
>> + compatible = "usbbda,5411";
>> + reg = <1>;
>> + peer-hub = <&usb_hub_3_x>;
>> + };
>> +
>> + usb_hub_3_x: hub@2 {
>> + compatible = "usbbda,411";
>> + reg = <2>;
>> + peer-hub = <&usb_hub_2_x>;
>> + };
>> +};
>> +
>> +&usb_1_hsphy {
>> + vdd-supply = <&vreg_l4a_0p8>;
>> + vdda-pll-supply = <&vreg_l11a_1p8>;
>> + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
>> + qcom,imp-res-offset-value = <8>;
>> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
>> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
>> + qcom,bias-ctrl-value = <0x22>;
>> + qcom,charge-ctrl-value = <3>;
>> + qcom,hsdisc-trim-value = <0>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&usb_1_qmpphy {
>> + vdda-phy-supply = <&vreg_l3c_1p2>;
>> + vdda-pll-supply = <&vreg_l4a_0p8>;
>> + status = "okay";
>> +};
>> +
>> +&venus {
>> + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn";
>> +};
>> +
>> +&wifi {
>> + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
>> + vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
>> + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
>> + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
>> + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
>> + status = "okay";
>> +};
>> +
>> +&apps_rsc {
>> + pm6150-rpmh-regulators {
>> + compatible = "qcom,pm6150-rpmh-regulators";
>> + qcom,pmic-id = "a";
>> +
>> + vreg_s1a_1p1: smps1 {
>> + regulator-min-microvolt = <1128000>;
>> + regulator-max-microvolt = <1128000>;
>> + };
>> +
>> + vreg_l4a_0p8: ldo4 {
>> + regulator-min-microvolt = <824000>;
>> + regulator-max-microvolt = <928000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l9a_0p6: ldo9 {
>> + regulator-min-microvolt = <488000>;
>> + regulator-max-microvolt = <800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l10a_1p8: ldo10 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> +
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + vreg_l11a_1p8: ldo11 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l12a_1p8: ldo12 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l13a_1p8: ldo13 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l14a_1p8: ldo14 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l15a_1p8: ldo15 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l16a_2p7: ldo16 {
>> + regulator-min-microvolt = <2496000>;
>> + regulator-max-microvolt = <3304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l17a_3p0: ldo17 {
>> + regulator-min-microvolt = <2920000>;
>> + regulator-max-microvolt = <3232000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l18a_2p8: ldo18 {
>> + regulator-min-microvolt = <2496000>;
>> + regulator-max-microvolt = <3304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l19a_2p9: ldo19 {
>> + regulator-min-microvolt = <2960000>;
>> + regulator-max-microvolt = <2960000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> + };
>> +
>> + pm6150l-rpmh-regulators {
>> + compatible = "qcom,pm6150l-rpmh-regulators";
>> + qcom,pmic-id = "c";
>> +
>> + vreg_s8c_1p3: smps8 {
>> + regulator-min-microvolt = <1120000>;
>> + regulator-max-microvolt = <1408000>;
>> + };
>> +
>> + vreg_l1c_1p8: ldo1 {
>> + regulator-min-microvolt = <1616000>;
>> + regulator-max-microvolt = <1984000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l2c_1p3: ldo2 {
>> + regulator-min-microvolt = <1168000>;
>> + regulator-max-microvolt = <1304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l3c_1p2: ldo3 {
>> + regulator-min-microvolt = <1144000>;
>> + regulator-max-microvolt = <1304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l4c_1p8: ldo4 {
>> + regulator-min-microvolt = <1648000>;
>> + regulator-max-microvolt = <3304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + };
>> +
>> + vreg_l5c_1p8: ldo5 {
>> + regulator-min-microvolt = <1648000>;
>> + regulator-max-microvolt = <3304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + };
>> +
>> + vreg_l6c_2p9: ldo6 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <2950000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l7c_3p0: ldo7 {
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3312000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + };
>> +
>> + vreg_l8c_1p8: ldo8 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l9c_2p9: ldo9 {
>> + regulator-min-microvolt = <2952000>;
>> + regulator-max-microvolt = <2952000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l10c_3p3: ldo10 {
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3400000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l11c_3p3: ldo11 {
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3400000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_bob: bob {
>> + regulator-min-microvolt = <3008000>;
>> + regulator-max-microvolt = <3960000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
>> + };
>> + };
>> +};
>> +
>> +&qup_i2c2_default {
>> + drive-strength = <2>;
>> +
>> + /* Has external pullup */
>> + bias-disable;
>> +};
>> +
>> +&qup_i2c4_default {
>> + drive-strength = <2>;
>> +
>> + /* Has external pullup */
>> + bias-disable;
>> +};
>> +
>> +&qup_i2c9_default {
>> + drive-strength = <2>;
>> +
>> + /* Has external pullup */
>> + bias-disable;
>> +};
>> +
>> +&qup_i2c10_default {
>> + drive-strength = <2>;
>> +
>> + /* Has external pullup */
>> + bias-disable;
>> +};
>> +
>> +&tlmm {
>> + /*
>> + * The TZ seem to protect those because some boards can have
>> + * fingerprint sensor connected to this range. Not connected
>> + * on this board
>> + */
>> + gpio-reserved-ranges = <58 5>;
>> +
>> + amp_sd_mode_default: amp-sd-mode-deault-state {
>> + pins = "gpio23";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + bridge_en_default: bridge-en-default-state {
>> + pins = "gpio51";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + bridge_suspend_default: bridge-suspend-default-state {
>> + pins = "gpio22";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-pull-up;
>> + };
>> +
>> + codec_irq_default: codec-irq-deault-state {
>> + pins = "gpio28";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + edp_bridge_irq_default: edp-bridge-irq-default-state {
>> + pins = "gpio11";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + hid_keyboard_default: hid-keyboard-default-state {
>> + pins = "gpio33";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + hid_touchpad_default: hid-touchpad-default-state {
>> + pins = "gpio94";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + qup_uart3_sleep: qup-uart3-sleep-state {
>> + cts-pins {
>> + /*
>> + * Configure a pull-down on CTS to match the pull of
>> + * the Bluetooth module.
>> + */
>> + pins = "gpio38";
>> + function = "gpio";
>> + bias-pull-down;
>> + };
>> +
>> + rts-pins {
>> + /*
>> + * Configure pull-down on RTS. As RTS is active low
>> + * signal, pull it low to indicate the BT SoC that it
>> + * can wakeup the system anytime from suspend state by
>> + * pulling RX low (by sending wakeup bytes).
>> + */
>> + pins = "gpio39";
>> + function = "gpio";
>> + bias-pull-down;
>> + };
>> +
>> + tx-pins {
>> + /*
>> + * Configure pull-up on TX when it isn't actively driven
>> + * to prevent BT SoC from receiving garbage during sleep.
>> + */
>> + pins = "gpio40";
>> + function = "gpio";
>> + bias-pull-up;
>> + };
>> +
>> + rx-pins {
>> + /*
>> + * Configure a pull-up on RX. This is needed to avoid
>> + * garbage data when the TX pin of the Bluetooth module
>> + * is floating which may cause spurious wakeups.
>> + */
>> + pins = "gpio41";
>> + function = "gpio";
>> + bias-pull-up;
>> + };
>> + };
>> +
>> + reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state {
>> + pins = "gpio19";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state {
>> + pins = "gpio20";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + reg_lcm_en_default: reg-lcm-en-deault-state {
>> + pins = "gpio26";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + reg_audio_en_default: reg-audio-en-deault-state {
>> + pins = "gpio83";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + reg_tp_en_default: reg-tp-en-deault-state {
>> + pins = "gpio25";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + soc_bkoff_default: soc-bkoff-deault-state {
>> + pins = "gpio10";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + sdc1_default: sdc1-default-state {
>> + clk-pins {
>> + pins = "sdc1_clk";
>> + bias-disable;
>> + drive-strength = <16>;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc1_cmd";
>> + bias-pull-up;
>> + drive-strength = <16>;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc1_data";
>> + bias-pull-up;
>> + drive-strength = <16>;
>> + };
>> +
>> + rclk-pins {
>> + pins = "sdc1_rclk";
>> + bias-pull-down;
>> + };
>> + };
>> +
>> + sdc1_sleep: sdc1-sleep-state {
>> + clk-pins {
>> + pins = "sdc1_clk";
>> + bias-disable;
>> + drive-strength = <2>;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc1_cmd";
>> + bias-pull-up;
>> + drive-strength = <2>;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc1_data";
>> + bias-pull-up;
>> + drive-strength = <2>;
>> + };
>> +
>> + rclk-pins {
>> + pins = "sdc1_rclk";
>> + bias-pull-down;
>> + };
>> + };
>> +
>> + ter_mi2s_active: ter-mi2s-active-state {
>> + pins = "gpio63", "gpio64", "gpio65";
>> + function = "mi2s_2";
>> + };
>> +};
