On 10.03.2023 15:33, Yang Xiwen wrote:
> This commit adds support for the uz801 v3.0 WiFi/LTE dongle made by
> Henan Yiming Technology Co., Ltd. based on MSM8916.
>
> Note: The original firmware does not support 64-bit OS. It is necessary
> to flash 64-bit TZ firmware to boot arm64.
>
> Currently supported:
> - All CPU cores
> - Buttons
> - LEDs
> - Modem
> - SDHC
> - USB Device Mode
> - UART
>
> Signed-off-by: Yang Xiwen <forbidden405@xxxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Konrad
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/msm8916-yiming-uz801v3.dts | 35 +++++++++++++++++++
> 2 files changed, 36 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-yiming-uz801v3.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 31aa54f0428c3..0c4c71d6277b7 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += msm8916-yiming-uz801v3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-yiming-uz801v3.dts b/arch/arm64/boot/dts/qcom/msm8916-yiming-uz801v3.dts
> new file mode 100644
> index 0000000000000..74ce6563be183
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-yiming-uz801v3.dts
> @@ -0,0 +1,35 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-ufi.dtsi"
> +
> +/ {
> + model = "uz801 v3.0 4G Modem Stick";
> + compatible = "yiming,uz801-v3", "qcom,msm8916";
> +};
> +
> +&button_restart {
> + gpios = <&msmgpio 23 GPIO_ACTIVE_LOW>;
> +};
> +
> +&led_r {
> + gpios = <&msmgpio 7 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_g {
> + gpios = <&msmgpio 8 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_b {
> + gpios = <&msmgpio 6 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&button_default {
> + pins = "gpio23";
> + bias-pull-up;
> +};
> +
> +&gpio_leds_default {
> + pins = "gpio6", "gpio7", "gpio8";
> +};
