On 09/03/2023 19:38, Wesley Cheng wrote:
Hi Srinivas,
On 3/9/2023 1:01 AM, Srinivas Kandagatla wrote:
On 08/03/2023 23:57, Wesley Cheng wrote:
Create a USB BE component that will register a new USB port to the
ASoC USB
framework. This will handle determination on if the requested audio
profile is supported by the USB device currently selected.
Signed-off-by: Wesley Cheng <quic_wcheng@xxxxxxxxxxx>
Thanks Wesley for the patch, I have few minor comments.
Thanks for the review!
---
include/sound/q6usboffload.h | 20 ++++
sound/soc/qcom/Kconfig | 4 +
sound/soc/qcom/qdsp6/Makefile | 1 +
sound/soc/qcom/qdsp6/q6usb.c | 208 ++++++++++++++++++++++++++++++++++
4 files changed, 233 insertions(+)
create mode 100644 include/sound/q6usboffload.h
create mode 100644 sound/soc/qcom/qdsp6/q6usb.c
diff --git a/include/sound/q6usboffload.h b/include/sound/q6usboffload.h
new file mode 100644
index 000000000000..4fb1912d9f55
--- /dev/null
+++ b/include/sound/q6usboffload.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * linux/sound/q6usboffload.h -- QDSP6 USB offload
+ *
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All
rights reserved.
+ */
+
+/**
+ * struct q6usb_offload
+ * @dev - dev handle to usb be
+ * @sid - streamID for iommu
+ * @intr_num - usb interrupter number
+ * @domain - allocated iommu domain
+ **/
+struct q6usb_offload {
+ struct device *dev;
+ long long sid;
+ u32 intr_num;
+ struct iommu_domain *domain;
Why do we need to store this domain, You can remove this along with
the one line that gets domain in probe function.
We'll need a reference to the iommu domain, because the QC USB offload
driver will be the one that is going to map the XHCI interrupter and
transfer ring regions for the audio DSP. This happens when a USB QMI
this is okay, AFAIU, as long as uaudio_qdev->dev pointer is used in dma
alloc apis like dma_map*, dma_alloc_* you would not need to handle
iommu_domain directly like this in drivers.
--srini
enable stream request is received in the USB offload driver. Please
refer to:
static int prepare_qmi_response(struct snd_usb_substream *subs,
struct qmi_uaudio_stream_req_msg_v01 *req_msg,
struct qmi_uaudio_stream_resp_msg_v01 *resp, int info_idx)
{
...
xhci_pa = xhci_get_ir_resource(subs->dev, ir);
if (!xhci_pa) {
dev_err(uaudio_qdev->dev,
"failed to get sec event ring address\n");
ret = -ENODEV;
goto free_sec_ring;
}
...
va = uaudio_iommu_map(MEM_EVENT_RING, dma_coherent, xhci_pa,
PAGE_SIZE,
NULL);
if (!va) {
ret = -ENOMEM;
goto free_sec_ring;
}
This is just an example for mapping the XHCI secondary interrupter. We
will also do the same for the transfer ring.
Thanks
Wesley Cheng
