-------- 原始信息 --------
主题: Re: [PATCH v5 06/12] net: stmmac: Add glue layer for StarFive JH7110 SoC
From: Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx>
收件人: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
日期: 2023/3/10
> On Fri, 10 Mar 2023 at 01:02, Emil Renner Berthing
> <emil.renner.berthing@xxxxxxxxxxxxx> wrote:
>> On Fri, 3 Mar 2023 at 10:01, Samin Guo <samin.guo@xxxxxxxxxxxxxxxx> wrote:
>>>
>>> This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
>>>
>>> Co-developed-by: Emil Renner Berthing <kernel@xxxxxxxx>
>>> Signed-off-by: Emil Renner Berthing <kernel@xxxxxxxx>
>>> Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
>>> ---
>>> MAINTAINERS | 1 +
>>> drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++
>>> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
>>> .../ethernet/stmicro/stmmac/dwmac-starfive.c | 125 ++++++++++++++++++
>>> 4 files changed, 139 insertions(+)
>>> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>>>
>>> diff --git a/MAINTAINERS b/MAINTAINERS
>>> index 4e236b7c7fd2..91a4f190c827 100644
>>> --- a/MAINTAINERS
>>> +++ b/MAINTAINERS
>>> @@ -19916,6 +19916,7 @@ STARFIVE DWMAC GLUE LAYER
>>> M: Emil Renner Berthing <kernel@xxxxxxxx>
>>> M: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
>>> S: Maintained
>>> +F: Documentation/devicetree/bindings/net/dwmac-starfive.c
>>> F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml
>>>
>>> STARFIVE JH71X0 CLOCK DRIVERS
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
>>> index f77511fe4e87..47fbccef9d04 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
>>> @@ -165,6 +165,18 @@ config DWMAC_SOCFPGA
>>> for the stmmac device driver. This driver is used for
>>> arria5 and cyclone5 FPGA SoCs.
>>>
>>> +config DWMAC_STARFIVE
>>> + tristate "StarFive dwmac support"
>>> + depends on OF && (ARCH_STARFIVE || COMPILE_TEST)
>>> + depends on STMMAC_ETH
>>> + default ARCH_STARFIVE
>>> + help
>>> + Support for ethernet controllers on StarFive RISC-V SoCs
>>> +
>>> + This selects the StarFive platform specific glue layer support for
>>> + the stmmac device driver. This driver is used for StarFive JH7110
>>> + ethernet controller.
>>> +
>>> config DWMAC_STI
>>> tristate "STi GMAC support"
>>> default ARCH_STI
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
>>> index 057e4bab5c08..8738fdbb4b2d 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
>>> @@ -23,6 +23,7 @@ obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o
>>> obj-$(CONFIG_DWMAC_QCOM_ETHQOS) += dwmac-qcom-ethqos.o
>>> obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
>>> obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o
>>> +obj-$(CONFIG_DWMAC_STARFIVE) += dwmac-starfive.o
>>> obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
>>> obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o
>>> obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>>> new file mode 100644
>>> index 000000000000..566378306f67
>>> --- /dev/null
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
>>> @@ -0,0 +1,125 @@
>>> +// SPDX-License-Identifier: GPL-2.0+
>>> +/*
>>> + * StarFive DWMAC platform driver
>>> + *
>>> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
>>> + * Copyright (C) 2022 Emil Renner Berthing <kernel@xxxxxxxx>
>>> + *
>>> + */
>>> +
>>> +#include <linux/of_device.h>
>>> +
>>> +#include "stmmac_platform.h"
>>> +
>>> +struct starfive_dwmac {
>>> + struct device *dev;
>>> + struct clk *clk_tx;
>>> + struct clk *clk_gtx;
>>> + bool tx_use_rgmii_rxin_clk;
>>> +};
>>> +
>>> +static void starfive_eth_fix_mac_speed(void *priv, unsigned int speed)
>>> +{
>>> + struct starfive_dwmac *dwmac = priv;
>>> + unsigned long rate;
>>> + int err;
>>> +
>>> + /* Generally, the rgmii_tx clock is provided by the internal clock,
>>> + * which needs to match the corresponding clock frequency according
>>> + * to different speeds. If the rgmii_tx clock is provided by the
>>> + * external rgmii_rxin, there is no need to configure the clock
>>> + * internally, because rgmii_rxin will be adaptively adjusted.
>>> + */
>>> + if (dwmac->tx_use_rgmii_rxin_clk)
>>> + return;
>>> +
>>> + switch (speed) {
>>> + case SPEED_1000:
>>> + rate = 125000000;
>>> + break;
>>> + case SPEED_100:
>>> + rate = 25000000;
>>> + break;
>>> + case SPEED_10:
>>> + rate = 2500000;
>>> + break;
>>> + default:
>>> + dev_err(dwmac->dev, "invalid speed %u\n", speed);
>>> + break;
>>> + }
>>> +
>>> + err = clk_set_rate(dwmac->clk_tx, rate);
>>
>> Hi Samin,
>>
>> I tried exercising this code by forcing the interface to downgrade
>> from 1000Mbps to 100Mbps (ethtool -s end0 speed 100), and it doesn't
>> seem to work. The reason is that clk_tx is a mux, and when you call
>> clk_set_rate it will try to find the parent with the closest clock
>> rate instead of adjusting the current parent as is needed here.
>> However that is easily fixed by calling clk_set_rate on clk_gtx which
>> is just a gate that *will* propagate the rate change to the parent.
>>
>> With this change, this piece of code and downgrading from 1000Mbps to
>> 100Mbps works on the JH7100. However on the JH7110 there is a second
>> problem. The parent of clk_gtx, confusingly called
>> clk_gmac{0,1}_gtxclk is a divider (and gate) that takes the 1GHz PLL0
>> clock and divides it by some integer. But according to [1] it can at
>> most divide by 15 which is not enough to generate the 25MHz clock
>> needed for 100Mbps. So now I wonder how this is supposed to work on
>> the JH7110.
>>
>> [1]: https://doc-en.rvspace.org/JH7110/TRM/JH7110_TRM/sys_crg.html#sys_crg__section_skz_fxm_wsb
>
> Ah, I see now that gmac0_gtxclk is only used by gmac0 on the
> VisionFive 2 v1.2A, where I think it's a known problem that only
> 1000Mbps works.
> On the 1.3B this function is not used at all, and I guess it also
> ought to be skipped for gmac1 of the 1.2A using the rmii interface so
> it doesn't risk changing the parent of the tx clock.
>
Hi Emil,
V1.2A gmac0 only supports 1000M due to known problem, and v1.2A gmac1 supports 100M/10M.
V1.2A gmac1 uses a parent clock from gmac1_rmii_rtx, whose parent clock is from external phy clock gmac1_rmii_refin (fixed is 50M).
The default frequency division value of gmac1_rmii_rtx is 2, so it can work in 100M mode. （clk_tx: 50/2=25M ===> 100M mode）.
When gmac1 switches to 10M mode, the clock frequency of gmac1_rmii_rtx needs to be modified to 2.5M.
So,if 1.2A gmac1 is skipped the starfive_eth_fix_mac_speed, 10M mode will be unavailable.
gmac1_rmii_refin（50M) ==> gmac1_rmii_rtx（div 2, by default) ==> clk_tx (25M) （100M mode）
gmac1_rmii_refin（50M）==> gmac1_rmii_rtx（div 20) ==> clk_tx (2.5M) （10M mode）
Of course, as you mentioned earlier, we need to add gmac1_clk_tx uses CLK_SET_RATE_PARENT flag.
Best regards,
Samin
>>> + if (err)
>>> + dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate);
>>> +}
>>> +
>>> +static int starfive_dwmac_probe(struct platform_device *pdev)
>>> +{
>>> + struct plat_stmmacenet_data *plat_dat;
>>> + struct stmmac_resources stmmac_res;
>>> + struct starfive_dwmac *dwmac;
>>> + int err;
>>> +
>>> + err = stmmac_get_platform_resources(pdev, &stmmac_res);
>>> + if (err)
>>> + return err;
>>> +
>>> + plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
>>> + if (IS_ERR(plat_dat)) {
>>> + dev_err(&pdev->dev, "dt configuration failed\n");
>>> + return PTR_ERR(plat_dat);
>>> + }
>>> +
>>> + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
>>> + if (!dwmac)
>>> + return -ENOMEM;
>>> +
>>> + dwmac->clk_tx = devm_clk_get_enabled(&pdev->dev, "tx");
>>> + if (IS_ERR(dwmac->clk_tx))
>>> + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_tx),
>>> + "error getting tx clock\n");
>>> +
>>> + dwmac->clk_gtx = devm_clk_get_enabled(&pdev->dev, "gtx");
>>> + if (IS_ERR(dwmac->clk_gtx))
>>> + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_gtx),
>>> + "error getting gtx clock\n");
>>> +
>>> + if (device_property_read_bool(&pdev->dev, "starfive,tx-use-rgmii-clk"))
>>> + dwmac->tx_use_rgmii_rxin_clk = true;
>>> +
>>> + dwmac->dev = &pdev->dev;
>>> + plat_dat->fix_mac_speed = starfive_eth_fix_mac_speed;
>>> + plat_dat->init = NULL;
>>> + plat_dat->bsp_priv = dwmac;
>>> + plat_dat->dma_cfg->dche = true;
>>> +
>>> + err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
>>> + if (err) {
>>> + stmmac_remove_config_dt(pdev, plat_dat);
>>> + return err;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct of_device_id starfive_dwmac_match[] = {
>>> + { .compatible = "starfive,jh7110-dwmac" },
>>> + { /* sentinel */ }
>>> +};
>>> +MODULE_DEVICE_TABLE(of, starfive_dwmac_match);
>>> +
>>> +static struct platform_driver starfive_dwmac_driver = {
>>> + .probe = starfive_dwmac_probe,
>>> + .remove = stmmac_pltfr_remove,
>>> + .driver = {
>>> + .name = "starfive-dwmac",
>>> + .pm = &stmmac_pltfr_pm_ops,
>>> + .of_match_table = starfive_dwmac_match,
>>> + },
>>> +};
>>> +module_platform_driver(starfive_dwmac_driver);
>>> +
>>> +MODULE_LICENSE("GPL");
>>> +MODULE_DESCRIPTION("StarFive DWMAC platform driver");
>>> +MODULE_AUTHOR("Emil Renner Berthing <kernel@xxxxxxxx>");
>>> +MODULE_AUTHOR("Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>");
>>> --
>>> 2.17.1
>>>
>>>
>>> _______________________________________________
>>> linux-riscv mailing list
>>> linux-riscv@xxxxxxxxxxxxxxxxxxx
>>> http://lists.infradead.org/mailman/listinfo/linux-riscv
